简单拓扑

WLC配置

WLC#show running-config 
Building configuration...Current configuration : 11943 bytes
!
! Last configuration change at 16:22:44 UTC Thu Mar 14 2024 by admin
!
version 17.9
service timestamps debug datetime msec
service timestamps log datetime msec
service call-home
platform qfp utilization monitor load 80
platform punt-keepalive disable-kernel-core
!
hostname WLC
!
boot-start-marker
boot-end-marker
!
!
vrf definition Mgmt-intf!address-family ipv4exit-address-family!address-family ipv6exit-address-family
!         
aaa new-model
!         
!         
aaa authentication login testcisco local
!         
!         
aaa session-id common
vtp mode off
!         
!         
!         
!         
!         
!         
!         
ip dhcp excluded-address 192.168.2.1 192.168.2.2
ip dhcp excluded-address 192.168.3.1 192.168.3.2
!         
ip dhcp pool vlan100-apnetwork 192.168.2.0 255.255.255.0default-router 192.168.2.1 
!         
ip dhcp pool vlan200-usernetwork 192.168.3.0 255.255.255.0default-router 192.168.3.1 
!         
!         
!         
login on-success log
!         
!         
!         
!         
!         
!         
!         
subscriber templating
!         
!         
!         
!         
!         
!         
parameter-map type webauth globalvirtual-ip ipv4 192.0.2.1
!         
access-session mac-move deny
multilink bundle-name authenticated
!         
!         
!         
!         
username admin privilege 15 password 0 Lenovo123456
!         
redundancymode sso 
!         
!         
!         
vlan internal allocation policy ascending
!         
vlan 100  name ap  
!         
vlan 200  name user
!         
vlan 800  
!         
!         
!         
class-map match-any AVC-Reanchor-Classmatch protocol cisco-jabber-audiomatch protocol cisco-jabber-videomatch protocol webex-mediamatch protocol webex-app-sharingmatch protocol webex-controlmatch protocol webex-meetingmatch protocol wifi-calling
!                 
!         
!         
interface TwoGigabitEthernet0/0/0switchport mode trunknegotiation auto
!         
interface TwoGigabitEthernet0/0/1switchport access vlan 100switchport mode accessnegotiation auto
!         
interface TwoGigabitEthernet0/0/2negotiation auto
!         
interface TwoGigabitEthernet0/0/3negotiation auto
!         
interface TenGigabitEthernet0/1/0negotiation auto
!         
interface TenGigabitEthernet0/1/1switchport trunk allowed vlan 800switchport mode trunknegotiation auto
!         
interface GigabitEthernet0vrf forwarding Mgmt-intfip address 192.168.1.1 255.255.255.0negotiation auto
!         
interface Vlan1no ip address
!         
interface Vlan100ip address 192.168.2.1 255.255.255.0
!         
interface Vlan200ip address 192.168.3.1 255.255.255.0
!         
interface Vlan800no ip address
!         
ip http server
ip http authentication local
ip http secure-server
ip forward-protocol nd
!         
ip tftp source-interface GigabitEthernet0
ip route 0.0.0.0 0.0.0.0 192.168.1.1
!         
!         
ip access-list standard 110 permit 0.0.0.0 255.255.255.020 permit 192.168.1.0 0.0.0.255
!         
!         
!         
!         
!         
!         
control-plane
!         
!         
!         
!         
!         
!         
line con 0stopbits 1
line aux 0
line vty 0 4password hlj123456login authentication testciscotransport input telnet
line vty 5 15transport input ssh
!         
call-home ! If contact email address in call-home is configured as sch-smart-licensing@cisco.com! the email address configured in Cisco Smart License Portal will be used as contact email address to send SCH notifications.contact-email-addr sch-smart-licensing@cisco.comprofile "CiscoTAC-1"active  destination transport-method http
!         
!         
!         
!         
!         
!         
wireless aaa policy default-aaa-policy
wireless cts-sxp profile default-sxp-profile
wireless management interface Vlan100  # 配置管理接口capwap-discovery public
wireless profile airtime-fairness default-atf-policy 0
wireless profile flex default-flex-profiledescription "default flex profile"ip http client proxy 0.0.0.0 0
wireless profile mesh default-mesh-profiledescription "default mesh profile"
wireless profile multi-bssid default-multi-bssid-profiledescription "Default multi bssid profile"
wireless profile radio default-radio-profileantenna count 0description "Preconfigured default radio profile"
wireless profile policy default-policy-profileautoqos mode voicedescription "default policy profile"et-analytics enablepassive-clientservice-policy input platinum-upservice-policy output platinumvlan userno shutdown
wireless tag site default-site-tagdescription "default site tag"fabric control-plane default-control-plane
wireless tag policy default-policy-tagdescription "default policy-tag"wlan testcisco policy default-policy-profile
wireless tag rf default-rf-tagdescription "default RF tag"
wireless fabric control-plane default-control-plane
wireless country CN
wlan testcisco 1 testciscodot11ax target-waketimedot11ax twt-broadcast-supportsecurity wpa psk set-key ascii 0 testciscono security wpa akm dot1xsecurity wpa akm pskno shutdown
ap dot11 24ghz rf-profile Low_Client_Density_rf_24ghcoverage data rssi threshold -90coverage level 2coverage voice rssi threshold -90description "pre configured Low Client Density rfprofile for 2.4gh radio"high-density rx-sop threshold lowrate RATE_12M supportedrate RATE_24M supportedrate RATE_6M supportedtx-power v1 threshold -65no shutdown
ap dot11 24ghz rf-profile High_Client_Density_rf_24ghdescription "pre configured High Client Density rfprofile for 2.4gh radio"high-density rx-sop threshold mediumrate RATE_11M disablerate RATE_12M mandatoryrate RATE_1M disablerate RATE_24M supportedrate RATE_2M disablerate RATE_5_5M disablerate RATE_6M disabletx-power min 7no shutdown
ap dot11 24ghz rf-profile Typical_Client_Density_rf_24ghdescription "pre configured Typical Client Density rfprofile for 2.4gh radio"rate RATE_11M disablerate RATE_12M mandatoryrate RATE_1M disablerate RATE_24M supportedrate RATE_2M disablerate RATE_5_5M disablerate RATE_6M disableno shutdown
ap dot11 24ghz cac voice acm
ap dot11 24ghz rate RATE_12M supported
ap dot11 24ghz rate RATE_24M supported
ap dot11 24ghz rate RATE_6M supported
ap dot11 6ghz rf-profile default-rf-profile-6ghzdescription "default rfprofile for 6GHz radio"rate RATE_12M mandatoryrate RATE_24M mandatoryrate RATE_6M mandatoryno shutdown
ap dot11 5ghz rf-profile Low_Client_Density_rf_5ghcoverage data rssi threshold -90coverage level 2coverage voice rssi threshold -90description "pre configured Low Client Density rfprofile for 5gh radio"high-density rx-sop threshold lowrate RATE_12M mandatoryrate RATE_24M mandatoryrate RATE_6M mandatorytx-power v1 threshold -60no shutdown
ap dot11 5ghz rf-profile High_Client_Density_rf_5ghdescription "pre configured High Client Density rfprofile for 5gh radio"high-density rx-sop threshold mediumrate RATE_12M mandatoryrate RATE_24M mandatoryrate RATE_6M disablerate RATE_9M disabletx-power min 7tx-power v1 threshold -65no shutdown
ap dot11 5ghz rf-profile Typical_Client_Density_rf_5ghdescription "pre configured Typical Density rfprofile for 5gh radio"rate RATE_12M mandatoryrate RATE_24M mandatoryrate RATE_6M mandatoryno shutdown
ap dot11 5ghz cac voice acm
ap dot11 5ghz rate RATE_12M mandatory
ap dot11 5ghz rate RATE_24M mandatory
ap dot11 5ghz rate RATE_6M mandatory
ap dot11 6ghz cac voice acm
ap dot11 6ghz rrm monitor measurement 600
ap tag-source-priority 2 source filter
ap tag-source-priority 3 source ap
ap profile default-ap-profilecountry CNdescription "default ap profile"ntp ip 0.0.0.0syslog host 255.255.255.255
trapflags ap crash
trapflags ap noradiocards
trapflags ap register
end

其中无线的配置参考思科官方视频：https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/videos/Basic-Configuration-of-Cisco-Catalyst-9800-Series-Wireless-Controller.html
9800无线控制器配置手册：https://www.cisco.com/c/zh_cn/support/wireless/catalyst-9800-series-wireless-controllers/products-installation-and-configuration-guides-list.html
思科命令集：https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-13/cmd-ref/b_wl_17_13_cr/configuration-commands-a-to-f.html