20241102解决荣品PRO-RK3566开发板刷Rockchip原厂的Buildroot使用荣品的DTS出现

20241102解决荣品PRO-RK3566开发板刷Rockchip原厂的Buildroot使用荣品的DTS出现fiq_debugger问题
2024/11/2 9:46


缘起:给荣品PRO-RK3566开发板刷Rockchip原厂的Buildroot时,DEBUG波特率是1.5Mbps。
但是启动到FIQ阶段,在你使用荣品的DTS的时候,就会切换到115200bps。
调试的时候,肯定/100%要求是固定在一个默认波特率上。
因此就直接以Rockchip原厂的1.5Mbps为准了。


初步判定:Rockchip原厂的Buildroot默认波特率是1.5Mbps N 8 1
荣品的DTS配置DEBUG的默认波特率是115200bps N 8 1
直接通过grep查找115200,把找到的地方都修改/屏蔽掉即可。


Z:\RK3566_RK3568_Linux5.10_V1.2.0\kernel\arch\arm64\boot\dts\rockchip\pro-rk3566.dts

    test-power {
        /** disable for use rk809-battery */
        status = "disabled";
    };
    charge-animation {
        compatible = "rockchip,uboot-charge";
        rockchip,uboot-charge-on = <0>;
        rockchip,android-charge-on = <0>;
        rockchip,uboot-low-power-voltage = <7000>;
        rockchip,screen-on-voltage = <7000>;
        status = "okay";
    };

    //fiq-debugger {
    //    compatible = "rockchip,fiq-debugger";
    //    rockchip,serial-id = <2>;
    //    rockchip,wake-irq = <0>;
    //    /* If enable uart uses irq instead of fiq */
    //    rockchip,irq-mode-enable = <1>;
    //    rockchip,baudrate = <115200>;  /* Only 115200 and 1500000 */
    //    interrupts = <GIC_SPI 252 IRQ_TYPE_LEVEL_LOW>;
    //    pinctrl-names = "default";
    //    pinctrl-0 = <&uart2m0_xfer>;
    //    status = "okay";
    //};
};


&pmu_io_domains {
        status = "okay";
        pmuio2-supply = <&vcc3v3_pmu>;
        vccio1-supply = <&vccio_acodec>;
        vccio3-supply = <&vccio_sd>;
        vccio4-supply = <&vcc_3v3>;
        vccio5-supply = <&vcc_3v3>;
        vccio6-supply = <&vcc_1v8>;
        vccio7-supply = <&vcc_3v3>;
};


1.5Mbps波特率:

[BEGIN] 2024/11/2 9:37:29
DDR 2d653b3476 typ 24/01/20-15:04:19,fwver: v1.21
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=4096MB
tdqss: cs0 dqs0: 48ps, dqs1: -120ps, dqs2: -72ps, dqs3: -192ps, 
tdqss: cs1 dqs0: -24ps, dqs1: -120ps, dqs2: -72ps, dqs3: -168ps, 

change to: 324MHz
PHY drv:clk:36,ca:36,DQ:29,odt:0
vrefinner:24%, vrefout:41%
dram drv:40,odt:0
clk skew:0x62
rx vref: 22.4%
tx vref: 38.0%

change to: 528MHz
PHY drv:clk:36,ca:36,DQ:29,odt:0
vrefinner:24%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
rx vref: 28.4%
tx vref: 36.0%

change to: 780MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
rx vref: 15.6%
tx vref: 32.0%

change to: 1056MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x38
rx vref: 15.6%
tx vref: 19.8%
cs 0:
the read training result:
DQS0:0x3e, DQS1:0x40, DQS2:0x44, DQS3:0x3a, 
min  : 0xb  0xb  0xe  0xb  0x1  0x2  0x6  0x5 , 0x8  0x9  0x2  0x1  0xd  0xb  0xc  0xa ,
      0x11  0xf  0xf  0xd  0x4  0x1  0x4  0x8 , 0xb  0x9  0x6  0x1  0xc  0xe  0x9  0xe ,
mid  :0x2a 0x2a 0x2b 0x2a 0x1f 0x20 0x24 0x23 ,0x27 0x28 0x22 0x20 0x2b 0x2a 0x2b 0x29 ,
      0x30 0x2e 0x2d 0x2c 0x23 0x20 0x21 0x25 ,0x29 0x27 0x24 0x20 0x2a 0x2c 0x28 0x2c ,
max  :0x49 0x49 0x49 0x49 0x3e 0x3f 0x42 0x42 ,0x47 0x48 0x42 0x40 0x49 0x4a 0x4a 0x48 ,
      0x50 0x4e 0x4b 0x4c 0x42 0x3f 0x3f 0x43 ,0x48 0x45 0x43 0x3f 0x49 0x4b 0x47 0x4a ,
range:0x3e 0x3e 0x3b 0x3e 0x3d 0x3d 0x3c 0x3d ,0x3f 0x3f 0x40 0x3f 0x3c 0x3f 0x3e 0x3e ,
      0x3f 0x3f 0x3c 0x3f 0x3e 0x3e 0x3b 0x3b ,0x3d 0x3c 0x3d 0x3e 0x3d 0x3d 0x3e 0x3c ,
the write training result:
DQS0:0x35, DQS1:0x28, DQS2:0x2f, DQS3:0x22, 
min  :0x58 0x5c 0x5c 0x5b 0x51 0x54 0x53 0x53 0x56 ,0x4a 0x4a 0x43 0x44 0x4d 0x4d 0x4e 0x4c 0x4a ,
      0x5c 0x5c 0x58 0x58 0x54 0x51 0x50 0x55 0x58 ,0x50 0x50 0x4d 0x4a 0x55 0x55 0x4e 0x54 0x4e ,
mid  :0x73 0x76 0x77 0x75 0x6b 0x6d 0x6e 0x6e 0x71 ,0x65 0x65 0x5f 0x5f 0x68 0x68 0x69 0x67 0x66 ,
      0x77 0x77 0x73 0x73 0x6d 0x69 0x6a 0x6f 0x72 ,0x6c 0x6a 0x68 0x64 0x6f 0x6f 0x6a 0x6e 0x6a ,
max  :0x8e 0x90 0x92 0x90 0x86 0x86 0x8a 0x8a 0x8c ,0x81 0x80 0x7b 0x7a 0x84 0x83 0x84 0x83 0x82 ,
      0x93 0x92 0x8e 0x8f 0x87 0x82 0x84 0x8a 0x8d ,0x89 0x84 0x84 0x7f 0x89 0x89 0x87 0x89 0x87 ,
range:0x36 0x34 0x36 0x35 0x35 0x32 0x37 0x37 0x36 ,0x37 0x36 0x38 0x36 0x37 0x36 0x36 0x37 0x38 ,
      0x37 0x36 0x36 0x37 0x33 0x31 0x34 0x35 0x35 ,0x39 0x34 0x37 0x35 0x34 0x34 0x39 0x35 0x39 ,
cs 1:
the read training result:
DQS0:0x3e, DQS1:0x40, DQS2:0x44, DQS3:0x3a, 
min  : 0xb  0xb  0xe  0xb  0x1  0x2  0x6  0x5 , 0x8  0x9  0x2  0x1  0xd  0xb  0xc  0xa ,
      0x11  0xf  0xf  0xd  0x4  0x1  0x4  0x8 , 0xb  0x9  0x6  0x1  0xc  0xe  0x9  0xe ,
mid  :0x2a 0x2a 0x2b 0x2a 0x1f 0x20 0x24 0x23 ,0x27 0x28 0x22 0x20 0x2b 0x2a 0x2b 0x29 ,
      0x30 0x2e 0x2d 0x2c 0x23 0x20 0x21 0x25 ,0x29 0x27 0x24 0x20 0x2a 0x2c 0x28 0x2c ,
max  :0x49 0x49 0x49 0x49 0x3e 0x3f 0x42 0x42 ,0x47 0x48 0x42 0x40 0x49 0x4a 0x4a 0x48 ,
      0x50 0x4e 0x4b 0x4c 0x42 0x3f 0x3f 0x43 ,0x48 0x45 0x43 0x3f 0x49 0x4b 0x47 0x4a ,
range:0x3e 0x3e 0x3b 0x3e 0x3d 0x3d 0x3c 0x3d ,0x3f 0x3f 0x40 0x3f 0x3c 0x3f 0x3e 0x3e ,
      0x3f 0x3f 0x3c 0x3f 0x3e 0x3e 0x3b 0x3b ,0x3d 0x3c 0x3d 0x3e 0x3d 0x3d 0x3e 0x3c ,
the write training result:
DQS0:0x35, DQS1:0x28, DQS2:0x2f, DQS3:0x22, 
min  :0x58 0x5c 0x5c 0x5b 0x51 0x54 0x53 0x53 0x56 ,0x4a 0x4a 0x43 0x44 0x4d 0x4d 0x4e 0x4c 0x4a ,
      0x5c 0x5c 0x58 0x58 0x54 0x51 0x50 0x55 0x58 ,0x50 0x50 0x4d 0x4a 0x55 0x55 0x4e 0x54 0x4e ,
mid  :0x73 0x76 0x77 0x75 0x6b 0x6d 0x6e 0x6e 0x71 ,0x65 0x65 0x5f 0x5f 0x68 0x68 0x69 0x67 0x66 ,
      0x77 0x77 0x73 0x73 0x6d 0x69 0x6a 0x6f 0x72 ,0x6c 0x6a 0x68 0x64 0x6f 0x6f 0x6a 0x6e 0x6a ,
max  :0x8e 0x90 0x92 0x90 0x86 0x86 0x8a 0x8a 0x8c ,0x81 0x80 0x7b 0x7a 0x84 0x83 0x84 0x83 0x82 ,
      0x93 0x92 0x8e 0x8f 0x87 0x82 0x84 0x8a 0x8d ,0x89 0x84 0x84 0x7f 0x89 0x89 0x87 0x89 0x87 ,
range:0x36 0x34 0x36 0x35 0x35 0x32 0x37 0x37 0x36 ,0x37 0x36 0x38 0x36 0x37 0x36 0x36 0x37 0x38 ,
      0x37 0x36 0x36 0x37 0x33 0x31 0x34 0x35 0x35 ,0x39 0x34 0x37 0x35 0x34 0x34 0x39 0x35 0x39 ,
CA Training result:
cs:0 min  :0x47 0x42 0x3c 0x35 0x3d 0x36 0x3f ,0x44 0x3e 0x3c 0x34 0x39 0x32 0x3e ,
cs:0 mid  :0x83 0x84 0x78 0x77 0x79 0x78 0x70 ,0x81 0x7f 0x78 0x76 0x76 0x74 0x6f ,
cs:0 max  :0xbf 0xc6 0xb4 0xb9 0xb6 0xba 0xa1 ,0xbf 0xc1 0xb4 0xb8 0xb3 0xb7 0xa0 ,
cs:0 range:0x78 0x84 0x78 0x84 0x79 0x84 0x62 ,0x7b 0x83 0x78 0x84 0x7a 0x85 0x62 ,
cs:1 min  :0x42 0x45 0x37 0x3a 0x39 0x3a 0x3b ,0x41 0x40 0x38 0x38 0x37 0x35 0x3b ,
cs:1 mid  :0x82 0x83 0x78 0x77 0x79 0x78 0x6f ,0x81 0x7e 0x77 0x76 0x76 0x74 0x6f ,
cs:1 max  :0xc3 0xc1 0xba 0xb5 0xba 0xb6 0xa4 ,0xc2 0xbd 0xb6 0xb5 0xb6 0xb4 0xa3 ,
cs:1 range:0x81 0x7c 0x83 0x7b 0x81 0x7c 0x69 ,0x81 0x7d 0x7e 0x7d 0x7f 0x7f 0x68 ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-g606f72bd97a-240527 #lxh (May 30 2024 - 16:08:15), fwver: v1.14
unknown raw ID 0 0 0
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 0
spl: mmc init failed with error: -123
Trying to boot from MMC1
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 (gzip @0x00240000) ... sha256(c25a9e81e4...) + sha256(b5946ac63d...) + OK
## Checking uboot 0x00a00000 (gzip @0x00c00000) ... sha256(dda8703b05...) + sha256(f800e1c7a3...) + OK
## Checking fdt 0x00b4e820 ... sha256(a474c6bb61...) + OK
## Checking atf-2 0xfdcc1000 ... sha256(b8dca786b4...) + OK
## Checking atf-3 0x0006b000 ... sha256(2f91089eb7...) + OK
## Checking atf-4 0xfdcce000 ... sha256(86ef885748...) + OK
## Checking atf-5 0xfdcd0000 ... sha256(0b2b146c60...) + OK
## Checking atf-6 0x00069000 ... sha256(a9a1e63bef...) + OK
## Checking optee 0x08400000 (gzip @0x08600000) ... sha256(6221fce17a...) + sha256(28fba8b7d7...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 167.932/336.479 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-645-g8cea6ab0b:cl, fwver: v1.44
NOTICE:  BL31: Built : 16:36:43, Sep 19 2023
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid 220114
INFO:    l3 cache partition cfg-0
INFO:    dfs DDR fsp_param[0].freq_mhz= 1056MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
I/TC: 
I/TC: OP-TEE version: 3.13.0-791-g185dc3c92 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Tue Apr 16 10:47:32 CST 2024 aarch64, fwver: v2.12 
I/TC: OP-TEE memory: TEEOS 0x200000 TA 0xc00000 SHM 0x200000
I/TC: Primary CPU initializing
I/TC: CRYPTO_CRYPTO_VERSION_NEW no support. Skip all algo mode check.
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9
usb dr_mode not found
usb dr_mode not found


U-Boot 2017.09 (Nov 01 2024 - 11:56:47 +0800)

Model: Rockchip RK3568 Evaluation Board
MPIDR: 0x0
PreSerial: 2, raw, 0xfe660000
DRAM:  4 GiB
Sysmem: init
Relocation Offset: ed211000
Relocation fdt: eb9f8508 - eb9fece8
CR: M/C/I
usb dr_mode not found
usb dr_mode not found
Using default environment

optee api revision: 2.0
dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
MMC: no card present
mmc_init: -123, time 0
switch to partitions #0, OK
mmc0(part 0) is current device
Bootdev(scan): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
TEEC: Waring: Could not find security partition
DM: v1
boot mode: None
RESC: 'boot', blk@0x00019a95
resource: sha256+
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
usb dr_mode not found
usb dr_mode not found
I2c0 speed: 100000Hz
PMIC:  RK8090 (on=0x40, off=0x00)
vdd_logic init 950000 uV
vdd_gpu init 900000 uV
vdd_npu init 900000 uV
vsel-gpios- not found! Error: -2
vdd_cpu init 1000000 uV
io-domain: OK
INFO:    ddr dmc_fsp already initialized in loader.
Could not find baseparameter partition
Model: pro-rk3566
Enable charge animation display
Exit charge: due to not enable uboot charge
Rockchip UBOOT DRM driver version: v1.0.1
Assign plane mask automatically
VOP have 2 active VP
vp0 have layer nr:3[1 3 5 ], primary plane: 5
vp1 have layer nr:3[0 2 4 ], primary plane: 4
vp2 have layer nr:0[], primary plane: 0
Using display timing dts
dsi@fe060000:  detailed mode clock 51000 kHz, flags[a]
    H: 1024 1160 1164 1324
    V: 0600 0616 0618 0634
bus_format: 100e
VOP update mode to: 1024x600p61, type: MIPI0 for VP1
VP1 set crtc_clock to 51000KHz
Unsupported bt709f at 10bit csc depth, use bt601f instead
VOP VP1 enable Smart0[654x270->654x270@185x165] fmt[0] addr[0xedf00000]
final DSI-Link bandwidth: 480 Mbps x 4
xfer: num: 2, addr: 0x50
xfer: num: 2, addr: 0x50
Monitor has basic audio support
Could not find baseparameter partition
hdmi@fe0a0000:  detailed mode clock 148500 kHz, flags[5]
    H: 1920 2008 2052 2200
    V: 1080 1084 1089 1125
bus_format: 2025
VOP update mode to: 1920x1080p60, type: HDMI0 for VP0
VP0 set crtc_clock to 148500KHz
VOP VP0 enable Smart1[654x270->654x270@633x405] fmt[0] addr[0xedf00000]
CEA mode used vic=16
final pixclk = 148500000 tmdsclk = 148500000
PHY powered down in 0 iterations
PHY PLL locked 1 iterations
PHY powered down in 0 iterations
PHY PLL locked 1 iterations
sink has audio support
hdmi_set_clk_regenerator: fs=48000Hz ftdms=148.500MHz N=6144 cts=148500
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  apll 1104000 KHz
  dpll 528000 KHz
  gpll 1188000 KHz
  cpll 1000000 KHz
  npll 1200000 KHz
  vpll 612000 KHz
  hpll 148500 KHz
  ppll 200000 KHz
  armclk 1104000 KHz
  aclk_bus 150000 KHz
  pclk_bus 100000 KHz
  aclk_top_high 500000 KHz
  aclk_top_low 400000 KHz
  hclk_top 150000 KHz
  pclk_top 100000 KHz
  aclk_perimid 300000 KHz
  hclk_perimid 150000 KHz
  pclk_pmu 100000 KHz
Net:   eth1: ethernet@fe010000
Hit key to stop autoboot('CTRL+C'):  0 
ANDROID: reboot reason: "(none)"
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image at 0xe94a4ac0 with size 0x02352a00
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at e94a4ac0 ...
   Using 'conf' configuration
## Verified-boot: 0
   Trying 'kernel' kernel subimage
     Description:  unavailable
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0xe94cf2c0
     Data Size:    36864512 Bytes = 35.2 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x00280000
     Entry Point:  0x00280000
     Hash algo:    sha256
     Hash value:   f35f300057e8861d17532a75d31a265c39521245a749fb77e941e91704c00a75
   Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at e94a4ac0 ...
   Using 'conf' configuration
   Trying 'fdt' fdt subimage
     Description:  unavailable
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0xe94a52c0
     Data Size:    171637 Bytes = 167.6 KiB
     Architecture: AArch64
     Load Address: 0x08300000
     Hash algo:    sha256
     Hash value:   f7d05bec7b0df3ef8859e186d264cd5ff9b39d6ba73af446478a282eb725456d
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x08300000 to 0x08300000
   Booting using the fdt blob at 0x08300000
   Loading Kernel Image from 0xe94cf2c0 to 0x00280000 ... OK
   kernel loaded at 0x00280000, end = 0x025a8200
   Using Device Tree in place at 0000000008300000, end 000000000832ce74
vp0, plane_mask:0x2a, primary-id:5, curser-id:-1
vp1, plane_mask:0x15, primary-id:4, curser-id:-1
vp2, plane_mask:0x0, primary-id:0, curser-id:-1
## reserved-memory:
  drm-logo@00000000: addr=edf00000 size=15a000
  drm-cubic-lut@00000000: addr=eff00000 size=8000
  ramoops@110000: addr=110000 size=f0000
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x1f0000000 - 0x200000000 (size: 0x10000000)
board seed: Pseudo
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
No RNG device, ret=-12
== DO RELOCATE == Kernel from 0x00280000 to 0x00200000
Total: 1456.442/1504.614 ms

Starting kernel ...

[    1.509796] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    1.509821] Linux version 5.10.209 (viewpro@viewpro-ThinkBook-16-G5-IRH) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #1 SMP Fri Nov 1 11:57:02 CST 2024
[    1.511668] random: crng init done
[    1.515794] Machine model: pro-rk3566
[    1.550543] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '')
[    1.555089] printk: bootconsole [uart8250] enabled
[    1.556715] efi: UEFI not found.
[    1.616410] Zone ranges:
[    1.616664]   DMA      [mem 0x0000000000200000-0x00000000ffffffff]
[    1.617253]   DMA32    empty
[    1.617528]   Normal   [mem 0x0000000100000000-0x00000001ffffffff]
[    1.618112] Movable zone start for each node
[    1.618515] Early memory node ranges
[    1.618854]   node   0: [mem 0x0000000000200000-0x00000000083fffff]
[    1.619446]   node   0: [mem 0x0000000009400000-0x00000000efffffff]
[    1.620039]   node   0: [mem 0x00000001f0000000-0x00000001ffffffff]
[    1.620632] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[    1.640723] cma: Reserved 16 MiB at 0x00000000eec00000
[    1.641296] psci: probing for conduit method from DT.
[    1.641784] psci: PSCIv1.1 detected in firmware.
[    1.642221] psci: Using standard PSCI v0.2 function IDs
[    1.642718] psci: Trusted OS migration not required
[    1.643181] psci: SMC Calling Convention v1.2
[    1.643933] percpu: Embedded 30 pages/cpu s83800 r8192 d30888 u122880
[    1.644650] Detected VIPT I-cache on CPU0
[    1.645068] CPU features: detected: GIC system register CPU interface
[    1.645676] CPU features: detected: Virtualization Host Extensions
[    1.646263] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    1.646938] alternatives: patching kernel code
[    1.649201] Built 1 zonelists, mobility grouping on.  Total pages: 1027656
[    1.649856] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal  androidboot.verifiedbootstate=orange rw rootwait earlycon=uart8250,mmio32,0xfe660000 console=ttyFIQ0 root=PARTUUID=614e0000-0000 androidboot.fwver=ddr-v1.21-2d653b3476,spl-v1.14,bl31-v1.44,bl32-v2.12,uboot-11/01/2024
[    1.653735] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    1.654969] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    1.655701] mem auto-init: stack:off, heap alloc:off, heap free:off
[    1.672164] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB)
[    1.718644] Memory: 3974220K/4175872K available (18752K kernel code, 3488K rwdata, 6924K rodata, 6720K init, 592K bss, 185268K reserved, 16384K cma-reserved)
[    1.720091] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    1.720742] ftrace: allocating 57287 entries in 224 pages
[    1.794244] ftrace: allocated 224 pages with 3 groups
[    1.795023] rcu: Hierarchical RCU implementation.
[    1.795475] rcu:     RCU event tracing is enabled.
[    1.795904] rcu:     RCU dyntick-idle grace-period acceleration is enabled.
[    1.796535] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    1.797151]     Rude variant of Tasks RCU enabled.
[    1.797580] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    1.798291] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    1.803232] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    1.805412] GICv3: GIC: Using split EOI/Deactivate mode
[    1.805917] GICv3: 320 SPIs implemented
[    1.806281] GICv3: 0 Extended SPIs implemented
[    1.806734] GICv3: Distributor has no Range Selector support
[    1.807276] GICv3: 16 PPIs implemented
[    1.808052] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[    1.808821] ITS [mem 0xfd440000-0xfd45ffff]
[    1.809289] ITS@0x00000000fd440000: allocated 8192 Devices @2810000 (indirect, esz 8, psz 64K, shr 0)
[    1.810189] ITS@0x00000000fd440000: allocated 32768 Interrupt Collections @2820000 (flat, esz 2, psz 64K, shr 0)
[    1.811152] ITS: using cache flushing for cmd queue
[    1.811961] GICv3: using LPI property table @0x0000000002830000
[    1.812633] GIC: using cache flushing for LPI property table
[    1.813172] GICv3: CPU0: using allocated LPI pending table @0x0000000002840000
[    1.813922] rcu:     Offload RCU callbacks from CPUs: (none).
[    1.842968] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    1.843559] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    1.844581] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    1.846416] Console: colour dummy device 80x25
[    1.846882] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    1.847856] pid_max: default: 32768 minimum: 301
[    1.848407] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    1.849119] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    1.851191] rcu: Hierarchical SRCU implementation.
[    1.852294] Platform MSI: interrupt-controller@fd440000 domain created
[    1.853376] PCI/MSI: /interrupt-controller@fd400000/interrupt-controller@fd440000 domain created
[    1.854568] EFI services will not be available.
[    1.855279] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
[    1.856942] Detected VIPT I-cache on CPU1
[    1.856971] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[    1.856991] GICv3: CPU1: using allocated LPI pending table @0x0000000002850000
[    1.857043] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[    1.858312] Detected VIPT I-cache on CPU2
[    1.858336] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[    1.858352] GICv3: CPU2: using allocated LPI pending table @0x0000000002860000
[    1.858388] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[    1.859614] Detected VIPT I-cache on CPU3
[    1.859636] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[    1.859652] GICv3: CPU3: using allocated LPI pending table @0x0000000002870000
[    1.859686] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[    1.859781] smp: Brought up 1 node, 4 CPUs
[    1.867193] SMP: Total of 4 processors activated.
[    1.867647] CPU features: detected: Privileged Access Never
[    1.868172] CPU features: detected: LSE atomic instructions
[    1.868698] CPU features: detected: User Access Override
[    1.869198] CPU features: detected: 32-bit EL0 Support
[    1.869683] CPU features: detected: Common not Private translations
[    1.870272] CPU features: detected: RAS Extension Support
[    1.870781] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    1.871599] CPU features: detected: CRC32 instructions
[    1.872084] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    1.872739] CPU features: detected: RCpc load-acquire (LDAPR)
[    1.899748] CPU: All CPU(s) started at EL2
[    1.901498] devtmpfs: initialized
[    1.922136] Registered cp15_barrier emulation handler
[    1.922632] Registered setend emulation handler
[    1.923226] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    1.924156] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    1.925302] pinctrl core: initialized pinctrl subsystem
[    1.926337] DMI not present or invalid.
[    1.926955] NET: Registered protocol family 16
[    1.928787] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[    1.929592] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    1.932525] Registered FIQ tty driver
[    1.933219] thermal_sys: Registered thermal governor 'fair_share'
[    1.933225] thermal_sys: Registered thermal governor 'step_wise'
[    1.933803] thermal_sys: Registered thermal governor 'user_space'
[    1.934370] thermal_sys: Registered thermal governor 'power_allocator'
[    1.935221] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    1.936664] cpuidle: using governor menu
[    1.937296] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    1.938058] ASID allocator initialised with 65536 entries
[    1.940764] ramoops: dmesg-0    0x20000@0x0000000000110000
[    1.941283] ramoops: console    0x80000@0x0000000000130000
[    1.941791] ramoops: pmsg    0x50000@0x00000000001b0000
[    1.942614] printk: console [ramoops-1] enabled
[    1.943062] pstore: Registered ramoops as persistent store backend
[    1.943648] ramoops: using 0xf0000@0x110000, ecc: 0
[    1.981342] rockchip-gpio fdd60000.gpio0: probed /pinctrl/gpio0@fdd60000
[    1.982461] rockchip-gpio fe740000.gpio1: probed /pinctrl/gpio1@fe740000
[    1.983578] rockchip-gpio fe750000.gpio2: probed /pinctrl/gpio2@fe750000
[    1.984670] rockchip-gpio fe760000.gpio3: probed /pinctrl/gpio3@fe760000
[    1.985764] rockchip-gpio fe770000.gpio4: probed /pinctrl/gpio4@fe770000
[    1.986503] rockchip-pinctrl pinctrl: probed pinctrl
[    2.007823] fiq_debugger fiq_debugger.0: IRQ fiq not found
[    2.008362] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[    2.008913] fiq_debugger_probe: could not install nmi irq handler

拒绝访问。


Connection closed.

Disconnected from remote host(1M5UART21) at 09:38:49.

Type `help' to learn how to use Xshell prompt.
[C:\~]$ 

[END] 2024/11/2 9:38:56
 

115200bps波特率:

[BEGIN] 2024/11/2 9:40:08
 

2.036596] printk: console [ttyFIQ0] enabled
    2.036596] printk: console [ttyFIQ0] enabled
[    2.045745] printk: bootco[    2.045745] printk: bootconsole [uart8250] disabled
nsole [uart8250] disabled
[    2.056154] Registered fiq debugger ttyFIQ0
[    2.056849] vcc3v3_sys: supplied by dc_12v
[    2.057094] vcc5v0_sys: supplied by dc_12v
[    2.057369] vcc3v3_lcd0_n: supplied by vcc3v3_sys
[    2.057612] vcc3v3_lcd1_n: supplied by vcc3v3_sys
[    2.058708] iommu: Default domain type: Translated 
[    2.061999] SCSI subsystem initialized
[    2.062217] usbcore: registered new interface driver usbfs
[    2.062262] usbcore: registered new interface driver hub
[    2.062301] usbcore: registered new device driver usb
[    2.062388] mc: Linux media interface: v0.10
[    2.062421] videodev: Linux video capture interface: v2.00
[    2.062495] pps_core: LinuxPPS API ver. 1 registered
[    2.062504] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    2.062521] PTP clock support registered
[    2.062561] EDAC MC: Ver: 3.0.0
[    2.063490] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[    2.063556] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[    2.065384] Advanced Linux Sound Architecture Driver Initialized.
[    2.065793] Bluetooth: Core ver 2.22
[    2.065830] NET: Registered protocol family 31
[    2.065839] Bluetooth: HCI device and connection manager initialized
[    2.065852] Bluetooth: HCI socket layer initialized
[    2.065862] Bluetooth: L2CAP socket layer initialized
[    2.065881] Bluetooth: SCO socket layer initialized
[    2.066325] rockchip-cpuinfo cpuinfo: SoC        : 35662000
[    2.066338] rockchip-cpuinfo cpuinfo: Serial        : 35e261fa0f931014
[    2.067040] clocksource: Switched to clocksource arch_sys_counter
[    2.489419] NET: Registered protocol family 2
[    2.489654] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    2.491297] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[    2.491390] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    2.491557] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
[    2.491952] TCP: Hash tables configured (established 32768 bind 32768)
[    2.492060] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    2.492111] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    2.492271] NET: Registered protocol family 1
[    2.492708] RPC: Registered named UNIX socket transport module.
[    2.492718] RPC: Registered udp transport module.
[    2.492724] RPC: Registered tcp transport module.
[    2.492731] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.493659] PCI: CLS 0 bytes, default 64
[    2.496341] rockchip-thermal fe710000.tsadc: tsadc is probed successfully!
[    2.497347] hw perfevents: enabled with armv8_cortex_a55 PMU driver, 7 counters available
[    2.501363] Initialise system trusted keyrings
[    2.501509] workingset: timestamp_bits=62 max_order=20 bucket_order=0
[    2.505529] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.506062] NFS: Registering the id_resolver key type
[    2.506091] Key type id_resolver registered
[    2.506099] Key type id_legacy registered
[    2.506138] ntfs: driver 2.1.32 [Flags: R/O].
[    2.506328] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    2.506579] fuse: init (API version 7.32)
[    2.506866] SGI XFS with security attributes, no debug enabled
[    2.538323] NET: Registered protocol family 38
[    2.538348] Key type asymmetric registered
[    2.538357] Asymmetric key parser 'x509' registered
[    2.538399] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[    2.538409] io scheduler mq-deadline registered
[    2.538417] io scheduler kyber registered
[    2.539116] rockchip-csi2-dphy-hw fe870000.csi2-dphy-hw: csi2 dphy hw probe successfully!
[    2.539894] rockchip-csi2-dphy csi2-dphy1: csi2 dphy1 probe successfully!
[    2.549669] pwm-backlight backlight: supply power not found, using dummy regulator
[    2.550227] iep: Module initialized.
[    2.550292] mpp_service mpp-srv: unknown mpp version for missing VCS info
[    2.550303] mpp_service mpp-srv: probe start
[    2.552090] mpp_vdpu2 fdea0400.vdpu: Adding to iommu group 1
[    2.552290] mpp_vdpu2 fdea0400.vdpu: probe device
[    2.552571] mpp_vdpu2 fdea0400.vdpu: probing finish
[    2.552992] mpp_vepu2 fdee0000.vepu: Adding to iommu group 3
[    2.553154] mpp_vepu2 fdee0000.vepu: probing start
[    2.553388] mpp_vepu2 fdee0000.vepu: probing finish
[    2.553858] mpp-iep2 fdef0000.iep: Adding to iommu group 4
[    2.554014] mpp-iep2 fdef0000.iep: probe device
[    2.554258] mpp-iep2 fdef0000.iep: allocate roi buffer failed
[    2.554293] mpp-iep2 fdef0000.iep: probing finish
[    2.554671] mpp_jpgdec fded0000.jpegd: Adding to iommu group 2
[    2.554819] mpp_jpgdec fded0000.jpegd: probe device
[    2.555078] mpp_jpgdec fded0000.jpegd: probing finish
[    2.556261] mpp_service mpp-srv: probe success
[    2.560552] dma-pl330 fe530000.dmac: Loaded driver for PL330 DMAC-241330
[    2.560576] dma-pl330 fe530000.dmac:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    2.562268] dma-pl330 fe550000.dmac: Loaded driver for PL330 DMAC-241330
[    2.562284] dma-pl330 fe550000.dmac:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    2.563036] rockchip-pvtm fde00000.pvtm: pvtm@0 probed
[    2.563172] rockchip-pvtm fde80000.pvtm: pvtm@1 probed
[    2.563277] rockchip-pvtm fde90000.pvtm: pvtm@2 probed
[    2.563962] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[    2.564591] arm-scmi firmware:scmi: Failed. SCMI protocol 22 not active.
[    2.564851] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    2.565846] fe650000.serial: ttyS1 at MMIO 0xfe650000 (irq = 71, base_baud = 1500000) is a 16550A
[    2.566412] fe670000.serial: ttyS3 at MMIO 0xfe670000 (irq = 72, base_baud = 1500000) is a 16550A
[    2.566947] fe6a0000.serial: ttyS6 at MMIO 0xfe6a0000 (irq = 73, base_baud = 1500000) is a 16550A
[    2.567459] fe6b0000.serial: ttyS7 at MMIO 0xfe6b0000 (irq = 74, base_baud = 1500000) is a 16550A
[    2.568117] fe6d0000.serial: ttyS9 at MMIO 0xfe6d0000 (irq = 75, base_baud = 1500000) is a 16550A
[    2.571128] rockchip-vop2 fe040000.vop: Adding to iommu group 8
[    2.579664] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x2a, primary plane phy id: 5
[    2.579693] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x15, primary plane phy id: 4
[    2.579704] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
[    2.579883] rockchip-vop2 fe040000.vop: [drm:vop2_bind] VP2 plane_mask is zero, so ignore register crtc
[    2.579976] [drm] failed to init overlay plane Cluster0-win1
[    2.580020] [drm] failed to init overlay plane Cluster1-win1
[    2.580152] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffffc00935f950)
[    2.580493] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[    2.581047] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[    2.581271] dwhdmi-rockchip fe0a0000.hdmi: IRQ index 1 not found
[    2.581632] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffffc00936e4d8)
[    2.581728] dw-mipi-dsi-rockchip fe060000.dsi: failed to find panel or bridge: -517
[    2.588656] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    2.589327] brd: module loaded
[    2.593871] loop: module loaded
[    2.594219] zram: Added device: zram0
[    2.594453] lkdtm: No crash points registered, enable through debugfs
[    2.595355] system_heap: orders[0] = 6
[    2.595369] system_heap: orders[1] = 4
[    2.595376] system_heap: orders[2] = 0
[    2.596967] ahci fc800000.sata: supply ahci not found, using dummy regulator
[    2.597122] ahci fc800000.sata: supply phy not found, using dummy regulator
[    2.597364] ahci fc800000.sata: supply target not found, using dummy regulator
[    2.597491] ahci fc800000.sata: forcing port_map 0x0 -> 0x1
[    2.597535] ahci fc800000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[    2.597547] ahci fc800000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc apst 
[    2.597566] ahci fc800000.sata: port 0 is not capable of FBS
[    2.598476] scsi host0: ahci
[    2.598743] ata1: SATA max UDMA/133 mmio [mem 0xfc800000-0xfc800fff] port 0x100 irq 19
[    2.601486] rockchip-spi fe620000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[    2.602912] rockchip-spi fe630000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[    2.604305] rockchip-spi fe640000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[    2.607661] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
[    2.607877] rk_gmac-dwmac fe010000.ethernet: supply phy not found, using dummy regulator
[    2.608021] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input).
[    2.608034] rk_gmac-dwmac fe010000.ethernet: TX delay(0x3a).
[    2.608045] rk_gmac-dwmac fe010000.ethernet: RX delay(0x29).
[    2.608059] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[    2.608093] rk_gmac-dwmac fe010000.ethernet: clock input from PHY
[    2.608334] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[    2.608544] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[    2.608557] rk_gmac-dwmac fe010000.ethernet:     DWMAC4/5
[    2.608568] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported
[    2.608577] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported
[    2.608584] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[    2.608591] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[    2.608649] rk_gmac-dwmac fe010000.ethernet: TSO supported
[    2.608659] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.608667] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[    2.608676] rk_gmac-dwmac fe010000.ethernet: Using 32 bits DMA width
[    2.743123] usbcore: registered new interface driver rtl8150
[    2.743182] usbcore: registered new interface driver r8152
[    2.754678] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.754710] ehci-pci: EHCI PCI platform driver
[    2.754786] ehci-platform: EHCI generic platform driver
[    2.755182] phy phy-fe8b0000.usb2-phy.4: illegal mode
[    2.757223] ehci-platform fd800000.usb: EHCI Host Controller
[    2.757385] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1
[    2.757513] ehci-platform fd800000.usb: irq 20, io mem 0xfd800000
[    2.770391] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00
[    2.770563] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.770575] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.770584] usb usb1: Product: EHCI Host Controller
[    2.770591] usb usb1: Manufacturer: Linux 5.10.209 ehci_hcd
[    2.770599] usb usb1: SerialNumber: fd800000.usb
[    2.770994] hub 1-0:1.0: USB hub found
[    2.771033] hub 1-0:1.0: 1 port detected
[    2.773681] ehci-platform fd880000.usb: EHCI Host Controller
[    2.773875] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 2
[    2.773992] ehci-platform fd880000.usb: irq 22, io mem 0xfd880000
[    2.787061] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00
[    2.787212] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.787225] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.787233] usb usb2: Product: EHCI Host Controller
[    2.787241] usb usb2: Manufacturer: Linux 5.10.209 ehci_hcd
[    2.787248] usb usb2: SerialNumber: fd880000.usb
[    2.787686] hub 2-0:1.0: USB hub found
[    2.787724] hub 2-0:1.0: 1 port detected
[    2.788405] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.788442] ohci-platform: OHCI generic platform driver
[    2.788754] phy phy-fe8b0000.usb2-phy.4: illegal mode
[    2.788768] ohci-platform fd840000.usb: Generic Platform OHCI controller
[    2.788921] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 3
[    2.789043] ohci-platform fd840000.usb: irq 21, io mem 0xfd840000
[    2.847845] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    2.847858] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.847867] usb usb3: Product: Generic Platform OHCI controller
[    2.847875] usb usb3: Manufacturer: Linux 5.10.209 ohci_hcd
[    2.847882] usb usb3: SerialNumber: fd840000.usb
[    2.848268] hub 3-0:1.0: USB hub found
[    2.848304] hub 3-0:1.0: 1 port detected
[    2.848790] ohci-platform fd8c0000.usb: Generic Platform OHCI controller
[    2.848938] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4
[    2.849039] ohci-platform fd8c0000.usb: irq 23, io mem 0xfd8c0000
[    2.907853] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    2.907866] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.907876] usb usb4: Product: Generic Platform OHCI controller
[    2.907884] usb usb4: Manufacturer: Linux 5.10.209 ohci_hcd
[    2.907891] usb usb4: SerialNumber: fd8c0000.usb
[    2.908269] hub 4-0:1.0: USB hub found
[    2.908308] hub 4-0:1.0: 1 port detected
[    2.909547] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    2.909710] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 5
[    2.909841] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000800002010010
[    2.909897] xhci-hcd xhci-hcd.0.auto: irq 89, io mem 0xfd000000
[    2.910021] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    2.910090] ata1: SATA link down (SStatus 0 SControl 300)
[    2.910175] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 6
[    2.910199] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    2.910332] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.910344] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.910353] usb usb5: Product: xHCI Host Controller
[    2.910397] usb usb5: Manufacturer: Linux 5.10.209 xhci-hcd
[    2.910407] usb usb5: SerialNumber: xhci-hcd.0.auto
[    2.910807] hub 5-0:1.0: USB hub found
[    2.910844] hub 5-0:1.0: 1 port detected
[    2.911159] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.911250] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[    2.911262] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.911271] usb usb6: Product: xHCI Host Controller
[    2.911279] usb usb6: Manufacturer: Linux 5.10.209 xhci-hcd
[    2.911286] usb usb6: SerialNumber: xhci-hcd.0.auto
[    2.911637] hub 6-0:1.0: USB hub found
[    2.911671] hub 6-0:1.0: 1 port detected
[    2.912065] usbcore: registered new interface driver cdc_acm
[    2.912075] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.912293] usbcore: registered new interface driver uas
[    2.912381] usbcore: registered new interface driver usb-storage
[    2.912472] usbcore: registered new interface driver usbserial_generic
[    2.912497] usbserial: USB Serial support registered for generic
[    2.912538] usbcore: registered new interface driver cp210x
[    2.912560] usbserial: USB Serial support registered for cp210x
[    2.912616] usbcore: registered new interface driver ftdi_sio
[    2.912641] usbserial: USB Serial support registered for FTDI USB Serial Device
[    2.912763] usbcore: registered new interface driver keyspan
[    2.912787] usbserial: USB Serial support registered for Keyspan - (without firmware)
[    2.912807] usbserial: USB Serial support registered for Keyspan 1 port adapter
[    2.912827] usbserial: USB Serial support registered for Keyspan 2 port adapter
[    2.912851] usbserial: USB Serial support registered for Keyspan 4 port adapter
[    2.912895] usbcore: registered new interface driver option
[    2.912918] usbserial: USB Serial support registered for GSM modem (1-port)
[    2.913067] usbcore: registered new interface driver oti6858
[    2.913089] usbserial: USB Serial support registered for oti6858
[    2.913134] usbcore: registered new interface driver pl2303
[    2.913156] usbserial: USB Serial support registered for pl2303
[    2.913202] usbcore: registered new interface driver qcserial
[    2.913225] usbserial: USB Serial support registered for Qualcomm USB modem
[    2.913276] usbcore: registered new interface driver sierra
[    2.913299] usbserial: USB Serial support registered for Sierra USB modem
[    2.914565] usbcore: registered new interface driver usbtouchscreen
[    2.915182] i2c /dev entries driver
[    2.918110] rk808 0-0020: chip id: 0x8090
[    2.918164] rk808 0-0020: No cache defaults, reading back from HW
[    2.941853] rk808 0-0020: source: on=0x10, off=0x00
[    2.941872] rk808 0-0020: support dcdc3 fb mode:-22, 1
[    2.941883] rk808 0-0020: support pmic reset mode:0,0
[    2.946904] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    2.946938] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    2.947365] vdd_logic: supplied by vcc3v3_sys
[    2.948346] vdd_gpu: supplied by vcc3v3_sys
[    2.948925] vcc_ddr: supplied by vcc3v3_sys
[    2.949493] vdd_npu: supplied by vcc3v3_sys
[    2.950412] vcc_1v8: supplied by vcc3v3_sys
[    2.950977] vdda0v9_image: supplied by vcc3v3_sys
[    2.952383] vdda_0v9: supplied by vcc3v3_sys
[    2.953457] vdda0v9_pmu: supplied by vcc3v3_sys
[    2.954539] vccio_acodec: supplied by vcc3v3_sys
[    2.955946] vccio_sd: supplied by vcc3v3_sys
[    2.957061] vcc3v3_pmu: supplied by vcc3v3_sys
[    2.958480] vcca_1v8: supplied by vcc3v3_sys
[    2.959557] vcca1v8_pmu: supplied by vcc3v3_sys
[    2.960645] vcca1v8_image: supplied by vcc3v3_sys
[    2.962047] vcc_3v3: supplied by vcc3v3_sys
[    2.962944] vcc3v3_sd: supplied by vcc3v3_sys
[    2.964387] rk817-battery rk817-battery: DMA mask not set
[    2.964523] rk817-battery rk817-battery: fb_temperature missing!
[    2.964537] rk817-battery rk817-battery: zero_reserve_dsoc missing!
[    2.964548] rk817-battery rk817-battery: low_power_sleep missing!
[    2.964558] rk817-battery rk817-battery: battery design_max_voltage missing!
[    2.987878] rk817-bat: initialized yet..
[    3.033993] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[    3.037066] usb 2-1: new high-speed USB device number 2 using ehci-platform
[    3.037583] rk817-charger: Failed to locate of_node [id: -1]
Start mounting all internal partitions in /etc/fstab
[    3.037735] rk817-charger rk817-charger: Failed to find matching dt id
Log saved to /var/log/mount-all.log
[    3.040845] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input0
Note: Will skip fsck, remove /.skip_fsck to enable
[    3.046675] rk808-rtc rk808-rtc: registered as rtc0
[    3.048434] rk808-rtc rk808-rtc: setting system clock to 2017-08-04T09:00:44 UTC (1501837244)
[    3.049907] fan53555-regulator 0-001c: Failed to get chip ID!
[    3.055899] rtc-hym8563 4-0051: rtc information is valid
[0]: Handling /dev/mmcblk0p6 / ext4 rw,noauto 1
[    3.061212] rtc-hym8563 4-0051: registered as rtc1
[    3.064829] rockchip-mipi-csi2-hw fdfb0000.mipi-csi2-hw: enter mipi csi2 hw probe!
[1]: Handling /dev/mmcblk0p7 /oem ext4 defaults 2
[    3.064992] rockchip-mipi-csi2-hw fdfb0000.mipi-csi2-hw: probe success, v4l2_dev:mipi-csi2-hw!
[2]: Handling /dev/mmcblk0p8 /userdata ext4 defaults 2
[    3.066436] rkisp_hw fdff0000.rkisp: Adding to iommu group 7
[    3.066662] rkisp_hw fdff0000.rkisp: is_thunderboot: 0
[    3.066692] rkisp_hw fdff0000.rkisp: can't request region for resource [mem 0xfdff0000-0xfdffffff]
[    3.066720] rkisp_hw fdff0000.rkisp: max input:0x0@0fps
[    3.066876] rkisp_hw fdff0000.rkisp: no find phandle sram
[2]: Already resized /dev/mmcblk0p8(ext4)
[    3.067391] rkisp rkisp-vir0: rkisp driver version: v02.05.01
[0]: Already resized /dev/mmcblk0p6(ext4)
[    3.067548] rkisp rkisp-vir0: No memory-region-thunderboot specified
[1]: Already resized /dev/mmcblk0p7(ext4)
[    3.067780] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
Starting syslogd: [    3.067804] rkisp rkisp-vir0: Entity type for entity rkisp-csi-subdev was not initialized!
OK
[    3.070439] usbcore: registered new interface driver uvcvideo
log-guardian: [WARN] Not a dir: "/var/log/,/tmp/"
[    3.070459] USB Video Class driver (1.1.1)
Starting klogd: log-guardian: Guarding logs in: "/var/log/,/tmp/"...
[    3.072086] Bluetooth: HCI UART driver ver 2.3
OK
[    3.072107] Bluetooth: HCI UART protocol H4 registered
Running sysctl: OK
[    3.072114] Bluetooth: HCI UART protocol ATH3K registered
[    3.072180] usbcore: registered new interface driver bfusb
[    3.072228] usbcore: registered new interface driver btusb
Populating /dev using udev: [    3.073075] cpu cpu0: bin=0
[    3.073141] cpu cpu0: leakage=24
[    3.073184] cpu cpu0: pvtm = 88110, from nvmem
[    3.073200] cpu cpu0: pvtm-volt-sel=2
[    3.073256] cpu cpu0: soc version=0, speed=2
[    3.075432] sdhci: Secure Digital Host Controller Interface driver
[    3.075450] sdhci: Copyright(c) Pierre Ossman
[    3.075465] Synopsys Designware Multimedia Card Interface Driver
[    3.076222] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.076756] dwmmc_rockchip fe000000.dwmmc: No normal pinctrl state
[    3.076774] dwmmc_rockchip fe000000.dwmmc: No idle pinctrl state
[    3.076835] dwmmc_rockchip fe2b0000.dwmmc: No normal pinctrl state
[    3.076850] dwmmc_rockchip fe2b0000.dwmmc: No idle pinctrl state
[    3.076900] dwmmc_rockchip fe000000.dwmmc: IDMAC supports 32-bit address mode.
[    3.076931] dwmmc_rockchip fe000000.dwmmc: Using internal DMA controller.
[    3.076943] dwmmc_rockchip fe000000.dwmmc: Version ID is 270a
[    3.076968] dwmmc_rockchip fe2b0000.dwmmc: IDMAC supports 32-bit address mode.
[    3.076994] dwmmc_rockchip fe2b0000.dwmmc: Using internal DMA controller.
[    3.077002] dwmmc_rockchip fe000000.dwmmc: DW MMC controller at irq 53,32 bit host data width,256 deep fifo
[    3.077015] dwmmc_rockchip fe2b0000.dwmmc: Version ID is 270a
[    3.077082] dwmmc_rockchip fe2b0000.dwmmc: DW MMC controller at irq 54,32 bit host data width,256 deep fifo
[    3.077437] dwmmc_rockchip fe000000.dwmmc: allocated mmc-pwrseq
[    3.077455] mmc_host mmc3: card is non-removable.
[    3.077841] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[    3.077927] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[    3.078850] cryptodev: driver 1.12 loaded.
[    3.078913] hid: raw HID events driver (C) Jiri Kosina
[    3.079230] usbcore: registered new interface driver usbhid
[    3.079241] usbhid: USB HID core driver
[    3.084956] usbcore: registered new interface driver snd-usb-audio
[    3.087255] rk817-codec rk817-codec: DMA mask not set
[    3.090641] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[    3.091554] rockchip-i2s-tdm fe410000.i2s: Register PCM for TRCM mode
[    3.094498] rk-multicodecs rk809-sound: Failed to get ADC channel
[    3.094634] rk-multicodecs rk809-sound: ASoC: Property 'rockchip,audio-routing' does not exist or its length is not even
[    3.095887] rk817-codec rk817-codec: rk817_probe: chip_name:0x80, chip_ver:0x95
[    3.100513] rk-multicodecs rk809-sound: Don't need to map headset detect gpio to irq
[    3.103972] Initializing XFRM netlink socket
[    3.104403] NET: Registered protocol family 10
[    3.105281] Segment Routing with IPv6
[    3.105345] NET: Registered protocol family 17
[    3.105369] NET: Registered protocol family 15
[    3.105601] Bluetooth: RFCOMM socket layer initialized
[    3.105636] Bluetooth: RFCOMM ver 1.11
[    3.105660] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.105673] Bluetooth: HIDP socket layer initialized
[    3.105715] [BT_RFKILL]: Enter rfkill_rk_init
[    3.105723] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    3.106427] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    3.106479] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6398s
[    3.106488] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    3.106495] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[    3.106529] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 124, flags = 0.
[    3.106542] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[    3.106548] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    3.106556] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[    3.106563] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[    3.107169] mmc0: SDHCI controller on fe310000.sdhci [fe310000.sdhci] using ADMA
[    3.107581] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 142.
[    3.107612] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 133.
[    3.107626] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 134.
[    3.107639] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 137.
[    3.107705] [BT_RFKILL]: Request irq for bt wakeup host
[    3.108125] [BT_RFKILL]: ** disable irq
[    3.108232] [BT_RFKILL]: bt_default device registered.
[    3.108346] input: bt-powerkey as /devices/platform/wireless-bluetooth/input/input1
[    3.108683] Key type dns_resolver registered
[    3.110460] Loading compiled-in X.509 certificates
[    3.111550] pstore: Using crash dump compression: deflate
[    3.112951] rga2 fdeb0000.rk_rga: probe successfully, irq = 31, hw_version:3.2.63318
[    3.113337] rga_iommu: IOMMU binding successfully, default mapping core[0x4]
[    3.113598] rga: Module initialized. v1.3.3
[    3.150118] mmc0: Host Software Queue enabled
[    3.150158] mmc0: new HS200 MMC card at address 0001
[    3.150857] mmcblk0: mmc0:0001 SPeMMC 29.0 GiB 
[    3.151066] mmcblk0boot0: mmc0:0001 SPeMMC partition 1 4.00 MiB
[    3.151279] mmcblk0boot1: mmc0:0001 SPeMMC partition 2 4.00 MiB
[    3.151612] mmcblk0rpmb: mmc0:0001 SPeMMC partition 3 4.00 MiB, chardev (236:0)
[    3.155073]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
done
[    3.186007] usb 2-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=61.60
[    3.186034] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
Starting irqbalance: [    3.186042] usb 2-1: Product: USB2.0 Hub
[    3.187004] hub 2-1:1.0: USB hub found
[    3.187495] hub 2-1:1.0: 4 ports detected
[    3.216397] vendor storage:20190527 ret = 0
[    3.294080] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
OK
[    3.306801] mpp_rkvenc fdf40000.rkvenc: Adding to iommu group 5
[    3.307097] mpp_rkvenc fdf40000.rkvenc: probing start
[    3.307599] mpp_rkvenc fdf40000.rkvenc: bin=0
[    3.307627] mpp_rkvenc fdf40000.rkvenc: Failed to get leakage
[    3.307681] mpp_rkvenc fdf40000.rkvenc: pvtm = 88110, from nvmem
[    3.307695] mpp_rkvenc fdf40000.rkvenc: pvtm-volt-sel=1
[    3.307888] mpp_rkvenc fdf40000.rkvenc: avs=0
[    3.308015] mpp_rkvenc fdf40000.rkvenc: failed to find power_model node
Initializing random number generator: OK
[    3.308027] mpp_rkvenc fdf40000.rkvenc: failed to initialize power model
Saving random seed: [    3.308035] mpp_rkvenc fdf40000.rkvenc: failed to get dynamic-coefficient
OK
[    3.308461] mpp_rkvenc fdf40000.rkvenc: probing finish
[    3.308865] mpp_rkvdec2 fdf80200.rkvdec: Adding to iommu group 6
[    3.309083] mpp_rkvdec2 fdf80200.rkvdec: rkvdec, probing start
[    3.309400] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_a is not found!
Starting system message bus: [    3.309412] rkvdec2_init:1024: No niu aclk reset resource define
[    3.309422] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_h is not found!
[    3.309429] rkvdec2_init:1027: No niu hclk reset resource define
[    3.309643] mpp_rkvdec2 fdf80200.rkvdec: bin=0
[    3.309749] mpp_rkvdec2 fdf80200.rkvdec: leakage=46
done
[    3.309764] mpp_rkvdec2 fdf80200.rkvdec: leakage-volt-sel=0
[    3.309803] mpp_rkvdec2 fdf80200.rkvdec: pvtm = 88110, from nvmem
[    3.309816] mpp_rkvdec2 fdf80200.rkvdec: pvtm-volt-sel=1
[    3.309997] mpp_rkvdec2 fdf80200.rkvdec: avs=0
[    3.310119] mpp_rkvdec2 fdf80200.rkvdec: failed to find power_model node
Starting bluetoothd: OK
[    3.310131] mpp_rkvdec2 fdf80200.rkvdec: failed to initialize power model
[    3.310140] mpp_rkvdec2 fdf80200.rkvdec: failed to get dynamic-coefficient
[    3.310264] mpp_rkvdec2 fdf80200.rkvdec: sram_start 0x00000000fdcc0000
Starting network: [    3.310275] mpp_rkvdec2 fdf80200.rkvdec: rcb_iova 0x0000000010000000
[    3.310283] mpp_rkvdec2 fdf80200.rkvdec: sram_size 45056
[    3.310290] mpp_rkvdec2 fdf80200.rkvdec: rcb_size 65536
[    3.310299] mpp_rkvdec2 fdf80200.rkvdec: min_width 512
[    3.310355] mpp_rkvdec2 fdf80200.rkvdec: link mode probe finish
[    3.310468] mpp_rkvdec2 fdf80200.rkvdec: probing finish
[    3.311685] rockchip-iodomain fdc20000.syscon:io-domains: pmuio2(3300000 uV) supplied by vcc3v3_pmu
[    3.311702] mali fde60000.gpu: Kernel DDK version g21p0-01eac0
[    3.311789] mali fde60000.gpu: GPU metrics tracepoint support enabled
[    3.311867] rockchip-iodomain fdc20000.syscon:io-domains: vccio1(3000000 uV) supplied by vccio_acodec
[    3.312012] rockchip-iodomain fdc20000.syscon:io-domains: vccio3(3300000 uV) supplied by vccio_sd
[    3.312140] rockchip-iodomain fdc20000.syscon:io-domains: vccio4(3300000 uV) supplied by vcc_3v3
[    3.312181] mali fde60000.gpu: bin=0
OK
[    3.312201] rockchip-iodomain fdc20000.syscon:io-domains: vccio5(3300000 uV) supplied by vcc_3v3
[    3.312234] mali fde60000.gpu: leakage=6
[    3.312275] mali fde60000.gpu: pvtm = 88110, from nvmem
[    3.312293] mali fde60000.gpu: pvtm-volt-sel=2
Starting dhcpcd...
[    3.312323] rockchip-iodomain fdc20000.syscon:io-domains: vccio6(1800000 uV) supplied by vcc_1v8
[    3.312342] mali fde60000.gpu: soc version=0, speed=2
dhcpcd-10.0.4 starting
[    3.312403] rockchip-iodomain fdc20000.syscon:io-domains: vccio7(3300000 uV) supplied by vcc_3v3
dev: loaded udev
[    3.312938] mali fde60000.gpu: avs=0
DUID 00:01:00:01:21:16:f4:3b:70:f7:54:9a:5f:9a
[    3.312963] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 143; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[    3.313406] mali fde60000.gpu: Register LUT 00070200 initialized for GPU arch 0x00070400
[    3.313443] mali fde60000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 status 0
[    3.313627] mali fde60000.gpu: No priority control manager is configured
[    3.313640] mali fde60000.gpu: Large page allocation set to false after hardware feature check
[    3.314060] mali fde60000.gpu: No memory group manager is configured
[    3.315611] mali fde60000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    3.317000] mali fde60000.gpu: Probed as mali0
[    3.317384] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x2a, primary plane phy id: 5
[    3.317407] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x15, primary plane phy id: 4
forked to background, child pid 495
[    3.317419] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
dhcpcd_fork_cb: truncated read 0 (expected 4)
[    3.317602] rockchip-vop2 fe040000.vop: [drm:vop2_bind] VP2 plane_mask is zero, so ignore register crtc
Starting chrony: [    3.317695] [drm] failed to init overlay plane Cluster0-win1
OK
[    3.317738] [drm] failed to init overlay plane Cluster1-win1
[    3.317869] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffffc00935f950)
starting weston... done.
[    3.318158] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[    3.319322] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
Starting dropbear sshd: [    3.320020] dwhdmi-rockchip fe0a0000.hdmi: IRQ index 1 not found
[    3.321071] input: hdmi_cec_key as /devices/platform/fe0a0000.hdmi/dw-hdmi-cec.4.auto/input/input2
OK
[    3.321958] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffffc00936e4d8)
[    3.322100] rockchip-drm display-subsystem: bound fe060000.dsi (ops 0xffffffc00936feb0)
Starting pulseaudio: OK
[    3.340623] mmc3: queuing unknown CIS tuple 0x80 (2 bytes)
[    3.342712] mmc3: queuing unknown CIS tuple 0x80 (3 bytes)
[    3.344617] mmc3: queuing unknown CIS tuple 0x80 (3 bytes)
[    3.348146] mmc3: queuing unknown CIS tuple 0x80 (7 bytes)
Starting dnsmasq: [    3.352576] mmc3: queuing unknown CIS tuple 0x81 (9 bytes)
[    3.434519] mmc_host mmc3: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
[    3.453861] dwmmc_rockchip fe000000.dwmmc: Successfully tuned phase to 270
[    3.459966] mmc3: new ultra high speed SDR104 SDIO card at address 0001
[    3.577784] rockchip-drm display-subsystem: [drm] fb0: rockchipdrmfb frame buffer device
[    3.578737] [drm] Initialized rockchip 3.0.0 20140818 for display-subsystem on minor 0
[    3.579342] input: adc-keys as /devices/platform/adc-keys/input/input3
[    3.586094] rockchip_headset rk-headset: Can not read property hook_gpio
OK
[    3.586125] rockchip_headset rk-headset: have not set adc chan
[    3.586136] rockchip_headset rk-headset: headset have no hook mode
[    3.586344] input: rk-headset as /devices/platform/rk-headset/input/input4
[    3.587188] RKNPU fde40000.npu: Adding to iommu group 0
W: [pulseaudio] main.c: This program is not intended to be run as root (unless --system is specified).
[    3.587730] RKNPU fde40000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
W: [pulseaudio] main.c: Compiled with DEPRECATED libsamplerate support!
[    3.588010] RKNPU fde40000.npu: can't request region for resource [mem 0xfde40000-0xfde4ffff]
    /bin/list-iodomain.sh version: V1.0.1 
[    3.588605] [drm] Initialized rknpu 0.9.6 20240322 for fde40000.npu on minor 1
[    3.589179] RKNPU fde40000.npu: bin=0
[    3.589232] RKNPU fde40000.npu: leakage=3
[    3.589273] RKNPU fde40000.npu: pvtm = 88110, from nvmem
[    3.589291] RKNPU fde40000.npu: pvtm-volt-sel=2
[    3.589307] RKNPU fde40000.npu: soc version=0, speed=2
[    3.589901] RKNPU fde40000.npu: avs=0
[    3.590083] RKNPU fde40000.npu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
fstrim: Starting fstrim process (638)...
[    3.590618] RKNPU fde40000.npu: failed to find power_model node
[    3.590633] RKNPU fde40000.npu: RKNPU: failed to initialize power model
Starting input-event-daemon: [    3.590641] RKNPU fde40000.npu: RKNPU: failed to get dynamic-coefficient
    Get CHIP ID: rk356x 
[    3.591709] cfg80211: Loading compiled-in X.509 certificates for regulatory database
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
[    3.593533] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
    XXXXXXXXXX      PLEASE CHECK IO-DOMAIN !!!!!!!!!!!!!!! 
[    3.594261] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
    XXXXXXXXXX        请务必检查IO电源域配置  !!!!!!!!!!!!!!! 
[    3.595209] rockchip-pm rockchip-suspend: not set pwm-regulator-config
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
[    3.595767] rockchip-suspend not set sleep-mode-config for mem-lite
    Get IO DOMAIN VALUE: 
[    3.595776] rockchip-suspend not set wakeup-config for mem-lite
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
[    3.595785] rockchip-suspend not set sleep-mode-config for mem-ultra
    注意事项:PMUIO1/PMUIO2 固定不可配 
[    3.595791] rockchip-suspend not set wakeup-config for mem-ultra
    VCCIO2电平由硬件FLASH_VOL_SEL决定: 
[    3.596937] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 406; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '11:59:03', on 'Nov  1 2024'.
    当VCCIo2供电是1.8V,则FLASH_VOL_SEL管脚必须保持为高电平; 
[    3.597438] Mali: 
    当VCCIO2供电是3.3V,则FLASH_VOL_SEL管脚必须保持为低电平; 
[    3.597442] Mali device driver loaded
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
[    3.597466] rkisp rkisp-vir0: clear unready subdev num: 1
done
[    3.597686] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
    pmuio2_vsel: 3.3V 
[    3.597700] cfg80211: failed to load regulatory.db
    vccio7_vsel: 3.3V 
[    3.598041] rkisp-vir0: update sensor failed
    vccio6_vsel: 1.8V 
[    3.598068] ALSA device list:
    vccio5_vsel: 3.3V 
[    3.598078]   #0: rockchip-rk809
    vccio4_vsel: 3.3V 
[    3.598085]   #1: rockchip,hdmi
    vccio3_vsel: 3.3V 
[    3.656764] EXT4-fs (mmcblk0p6): recovery complete
    vccio2_vsel: 3.3V 
[    3.656912] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)
    vccio1_vsel: 3.3V 
[    3.656981] VFS: Mounted root (ext4 filesystem) on device 179:6.
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
[    3.657870] devtmpfs: mounted
root@rk3566-buildroot:/# Date: 2017-08-04 UTC
[    3.663702] Freeing unused kernel memory: 6720K
[09:00:46.957] weston 13.0.1
[    3.663893] Run /sbin/init as init process
               https://wayland.freedesktop.org
[    3.731697] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
               Bug reports to: https://gitlab.freedesktop.org/wayland/weston/issues/
[    3.902683] EXT4-fs (mmcblk0p7): recovery complete
               Build: 13.0.1
[    3.902830] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null)
[09:00:46.959] Command line: /usr/bin/weston
[    3.902867] ext4 filesystem being mounted at /oem supports timestamps until 2038 (0x7fffffff)
[09:00:46.959] OS: Linux, 5.10.209, #1 SMP Fri Nov 1 11:57:02 CST 2024, aarch64
[    3.905675] EXT4-fs (mmcblk0p8): warning: mounting unchecked fs, running e2fsck is recommended
[09:00:46.959] Flight recorder: enabled
[    3.906461] EXT4-fs (mmcblk0p8): mounted filesystem without journal. Opts: (null)
[09:00:46.959] warning: XDG_RUNTIME_DIR "/var/run" is not configured
[    3.906494] ext4 filesystem being mounted at /userdata supports timestamps until 2038 (0x7fffffff)
correctly.  Unix access mode must be 0700 (current mode is 0755),
[    4.110445] ---headsetobserve_work---
and must be owned by the user UID 0 (current owner is UID 0).
[    4.201266] udevd[331]: starting version 3.2.10
Refer to your distribution on how to get it, or
[    4.217191] old_status == headset_info->headset_status
http://www.freedesktop.org/wiki/Specifications/basedir-spec
[    4.220654] udevd[332]: starting eudev-3.2.10
on how to implement it.
[09:00:46.968] Using config file '/etc/xdg/weston/weston.ini'
[09:00:46.971] Output repaint window is -1 ms maximum.
[09:00:46.974] Loading module '/usr/lib/libweston-13/drm-backend.so'
[09:00:46.981] initializing drm backend
[09:00:46.981] Entering mirror mode.
[09:00:46.981] Trying direct launcher...
[09:00:46.984] using /dev/dri/card0
[09:00:46.984] DRM: does not support atomic modesetting
[09:00:46.984] DRM: does not support GBM modifiers
[09:00:46.984] DRM: does not support async page flipping
[09:00:46.984] DRM: supports picture aspect ratio
[09:00:46.992] Loading module '/usr/lib/libweston-13/gl-renderer.so'
[09:00:47.035] EGL version: 1.4 Bifrost-"g13p0-01eac0"
[09:00:47.035] EGL vendor: ARM
[09:00:47.036] EGL client APIs: OpenGL_ES
[09:00:47.036] EGL features:
               EGL Wayland extension: yes
               context priority: yes
               buffer age: no
               partial update: yes
               swap buffers with damage: no
               configless context: yes
               surfaceless context: yes
               dmabuf support: modifiers
[09:00:47.063] GL version: OpenGL ES 3.2 v1.g13p0-01eac0.98c5dad4e3309b873e3189000b74ea36
[09:00:47.063] GLSL version: OpenGL ES GLSL ES 3.20
[09:00:47.063] GL vendor: ARM
[09:00:47.064] GL renderer: Mali-G52
E: [pulseaudio] module-rescue-streams.c: module-rescue-stream is obsolete and should no longer be loaded. Please remove it from your configuration.
E: [pulseaudio] module-console-kit.c: GetSessionsForUnixUser() call failed: org.freedesktop.DBus.Error.ServiceUnknown: The name org.freedesktop.ConsoleKit was not provided by any .service files
E: [pulseaudio] module.c: Failed to load module "module-console-kit" (argument: ""): initialization failed.
W: [pulseaudio] server-lookup.c: Unable to contact D-Bus: org.freedesktop.DBus.Error.NotSupported: Using X11 for dbus-daemon autolaunch was disabled at compile time, set your DBUS_SESSION_BUS_ADDRESS instead
W: [pulseaudio] main.c: Unable to contact D-Bus: org.freedesktop.DBus.Error.NotSupported: Using X11 for dbus-daemon autolaunch was disabled at compile time, set your DBUS_SESSION_BUS_ADDRESS instead
[09:00:47.372] GL ES 3.2 - renderer features:
               read-back format: ARGB8888
               glReadPixels supports y-flip: no
               wl_shm 10 bpc formats: yes
               wl_shm 16 bpc formats: no
               wl_shm half-float formats: no
               internal R and RG formats: yes
               OES_EGL_image_external: yes
               wl_shm sub-image to texture: yes
[09:00:47.372] Using GL renderer
[09:00:47.434] event3  - adc-keys: is tagged by udev as: Keyboard
[09:00:47.434] event3  - adc-keys: device is a keyboard
[09:00:47.437] event0  - rk805 pwrkey: is tagged by udev as: Keyboard
[09:00:47.437] event0  - rk805 pwrkey: device is a keyboard
[09:00:47.439] event2  - hdmi_cec_key: is tagged by udev as: Keyboard
[09:00:47.440] event2  - hdmi_cec_key: device is a keyboard
[09:00:47.442] event4  - rk-headset: is tagged by udev as: Keyboard
[09:00:47.442] event4  - rk-headset: device is a keyboard
[    6.078187] file system registered
[09:00:47.444] event1  - bt-powerkey: is tagged by udev as: Keyboard
[09:00:47.444] event1  - bt-powerkey: device is a keyboard
[09:00:47.514] libinput: configuring device "adc-keys".
[09:00:47.514] libinput: configuring device "rk805 pwrkey".
[09:00:47.514] libinput: configuring device "hdmi_cec_key".
[09:00:47.514] libinput: configuring device "rk-headset".
[    6.120567] bcmdhd: loading out-of-tree module taints kernel.
[09:00:47.515] libinput: configuring device "bt-powerkey".
[09:00:47.515] Registered plugin API 'weston_drm_output_api_v1' of size 40
[    6.137015] [dhd] _dhd_module_init: in Dongle Host Driver, version 101.10.591.52.27 (20240409-1)(20240411-2)(d83d8d7)
[09:00:47.515] Color manager: no-op
[    6.137015] /home/viewpro/RK3566_RK3568_Linux5.10_V1.2.0/external/rkwifibt/drivers/bcmdhd compiled on Nov  1 2024 at 12:42:22
[09:00:47.515] Compositor capabilities:
[    6.137015] 
               arbitrary surface rotation: yes
[    6.137088] [dhd] STATIC-MSG) dhd_static_buf_init : 101.10.361.36 (wlan=r892223-20231107-1)
               screen capture uses y-flip: yes
[    6.137180] [dhd] STATIC-MSG) dhd_init_wlan_mem : prealloc ok for index 0: 1102848(1077K)
               cursor planes: yes
[    6.137197] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
               arbitrary resolutions: no
[    6.137285] [dhd] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=117, oob_irq_flags=0x4
               view mask clipping: yes
[    6.137295] [dhd] dhd_wlan_init_gpio: WL_REG_ON=-1
               explicit sync: yes
[    6.137303] [dhd] dhd_wifi_platform_load: Enter
               color operations: no
[    6.137310] [dhd] Power-up adapter 'DHD generic adapter'
               presentation clock: CLOCK_MONOTONIC, id 1
[    6.137540] [dhd] dummy_probe: func->num=0x1; 
               presentation clock resolution: 0.000000001 s
[    6.137552] [dhd] dummy_probe: class=0xff; vendor=0x2d0; device=0xffff
[09:00:47.516] Loading module '/usr/lib/weston/desktop-shell.so'
[    6.139820] [dhd] dummy_probe: func->num=0x2; 

[    6.139851] [dhd] dummy_probe: class=0xff; vendor=0x2d0; device=0xffff
Handling start for Wi-Fi/BT chip:
[    6.140129] [dhd] dummy_probe: func->num=0x3; 
Broadcom    AP625X    sdio    02d0:a9bf    bcmdhd.ko    # AP6255/AP6256/AP6745
[    6.140152] [dhd] dummy_probe: class=0xff; vendor=0x2d0; device=0xffff
Starting Wi-Fi/BT...
[    6.140237] [dhd] wifi_platform_set_power = 1, delay: 200 msec
Wi-Fi/BT module: bcmdhd.ko
[    6.140247] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ========
Installing bcmdhd.ko ...
[    6.140255] [WLAN_RFKILL]: rockchip_wifi_power: 1
[09:00:47.559] DRM: head 'HDMI-A-1' found, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
[    6.140264] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
               Supported EOTF modes: SDR
[    6.140271] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0]
[09:00:47.560] DRM: head 'DSI-1' found, connector 180 is connected, EDID make 'unknown', model 'unknown', serial ''
[    6.181269] read descriptors
               Supported EOTF modes: SDR
[    6.181311] read strings
[09:00:47.560] launching '/usr/libexec/weston-keyboard'
[    6.344053] [dhd] wifi_platform_set_power = 1, sleep done: 200 msec
[09:00:47.563] launching '/usr/libexec/weston-desktop-shell'
[    6.344083] [dhd] wifi_platform_bus_enumerate device present 1
[09:00:47.566] HDMI-A-1 using at least 2 buffers
[    6.344091] [dhd] ======== Card detection to detect SDIO card! ========
[09:00:47.566] Output 'HDMI-A-1' attempts EOTF mode: SDR
[    6.360438] [dhd] bcmsdh_register: register client driver
[09:00:47.566] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[    6.360696] [dhd] bcmsdh_sdmmc_probe: Enter num=1
[09:00:47.567] Chosen EGL config details: id:   9 rgba: 8 8 8 0 buf: 24 dep:  0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[    6.360863] [dhd] bcmsdh_sdmmc_probe: Enter num=2
[09:00:47.567] Output HDMI-A-1 (crtc 71) video modes:
[    6.360876] [dhd] bus num (host idx)=3, slot num (rca)=1, caps=0x4008010d
               1920x1080@60.0, preferred, current, 148.5 MHz
[    6.360884] [dhd] found adapter info 'DHD generic adapter'
               1920x1080@60.0 16:9, 148.5 MHz
[    6.360897] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 3, size 139264
               1920x1080@59.9 16:9, 148.4 MHz
[    6.360933] [dhd] succeed to alloc static buf
               1920x1080i@60.0, 74.2 MHz
[    6.360940] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 4, size 0
               1920x1080i@60.0 16:9, 74.2 MHz
[    6.360986] [dhd] sdioh_attach: set sd_f2_blocksize 256
               1920x1080i@59.9 16:9, 74.2 MHz
[    6.361013] [dhd] sdioh_attach: sd clock rate = 150000000
               1920x1080@50.0 16:9, 148.5 MHz
[    6.361276] [dhd] dhdsdio_probe : no mutex held
               1920x1080i@50.0 16:9, 74.2 MHz
[    6.361288] [dhd] dhdsdio_probe : set mutex lock
               1680x1050@59.9, 119.0 MHz
[    6.361373] [dhd] F1 signature read @0x18000000=0x15294345
               1400x1050@59.9, 101.0 MHz
[    6.363411] [dhd] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9 pkg:0x2
               1600x900@60.0, 108.0 MHz
[    6.364153] [dhd] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
               1280x1024@75.0, 135.0 MHz
[    6.364250] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 7, size 42288
               1280x1024@60.0, 108.0 MHz
[    6.364285] [dhd] dhd_conf_set_chiprev : devid=0xa9bf, chip=0x4345, chiprev=9
               1440x900@59.9, 88.8 MHz
[    6.364332] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 0, size 10320
               1280x800@59.9, 71.0 MHz
[    6.364379] [dhd] dhd_ioctl_entry_local invalid parameter net 0000000000000000 dev_priv 0000000094cd3ebc
               1152x864@75.0, 108.0 MHz
[    6.364389] [dhd] CFG80211-ERROR) wl_is_fils_supported : FILS NOT supported, err -22
               1280x720@60.0, 74.2 MHz
[    6.364822] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 5, size 65536
               1280x720@60.0 16:9, 74.2 MHz
[    6.365220] [dhd] CFG80211-ERROR) wl_is_fils_supported : FILS NOT supported, err -19
               1280x720@59.9 16:9, 74.2 MHz
[    6.365921] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 19, size 65688
               1280x720@50.0 16:9, 74.2 MHz
[    6.366241] [dhd] dhd_attach(): thread:dhd_watchdog_thread:3e1 started
               1024x768@75.0, 78.8 MHz
[    6.366366] [dhd] dhd_attach(): thread:dhd_dpc:3e2 started
               1024x768@60.0, 65.0 MHz
[    6.366467] [dhd] dhd_attach(): thread:dhd_rxf:3e3 started
               800x600@75.0, 49.5 MHz
[    6.366486] [dhd] dhd_deferred_work_init: work queue initialized
               800x600@60.3, 40.0 MHz
[    6.366497] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2
               720x576@50.0 16:9, 27.0 MHz
[    6.366504] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40
               720x480@60.0 4:3, 27.0 MHz
[    6.366599] [dhd] sdioh_cis_read: func_cis_ptr[0]=0x10ac
               720x480@60.0 16:9, 27.0 MHz
[    6.371446] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 1, size 10300
               720x480@59.9, 27.0 MHz
[    6.371525] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 2, size 65536
               720x480@59.9 16:9, 27.0 MHz
[    6.371575] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN
               640x480@75.0, 31.5 MHz
[    6.371676] [dhd] Dongle Host Driver, version 101.10.591.52.27 (20240409-1)(20240411-2)(d83d8d7)
               640x480@60.0 4:3, 25.2 MHz
[    6.371676] /home/viewpro/RK3566_RK3568_Linux5.10_V1.2.0/external/rkwifibt/drivers/bcmdhd compiled on Nov  1 2024 at 12:42:22
               640x480@59.9, 25.2 MHz
[    6.371676] 
               640x480@59.9 4:3, 25.2 MHz
[    6.372395] [dhd] Register interface [wlan0]  MAC: 70:f7:54:9a:5f:9a
               720x400@70.1, 28.3 MHz
[    6.372395] 
[09:00:47.568] associating input device event3 with output HDMI-A-1 (none by udev)
[    6.372561] [dhd] [wlan0] wl_android_wifi_off :  g_wifi_on=1 force_off=1
[09:00:47.568] associating input device event0 with output HDMI-A-1 (none by udev)
[    6.372576] [dhd] dhd_bus_devreset: == Power OFF ==
[09:00:47.568] associating input device event2 with output HDMI-A-1 (none by udev)
[    6.372742] [dhd] dhd_bus_stop: making DHD_BUS_DOWN
[09:00:47.568] associating input device event4 with output HDMI-A-1 (none by udev)
[    6.372773] [dhd] bcmsdh_oob_intr_unregister: Enter
[09:00:47.568] associating input device event1 with output HDMI-A-1 (none by udev)
[    6.372782] [dhd] bcmsdh_oob_intr_unregister: irq is not registered
[09:00:47.568] Output HDMI-A-1 changed to mirror output
[    6.372794] [dhd] dhd_bus_devreset: making dhdpub up FALSE
[09:00:47.568] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[    6.372802] [dhd] dhd_txglom_enable: enable 0
[09:00:47.568] DSI-1 using at least 2 buffers
[    6.372809] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN
[09:00:47.569] Output 'DSI-1' attempts EOTF mode: SDR
[    6.372843] [dhd] wifi_platform_set_power = 0, delay: 10 msec
[09:00:47.569] Output 'DSI-1' using color profile: stock sRGB color profile
[    6.372853] [dhd] ======== PULL WL_REG_ON(-1) LOW! ========
[09:00:47.569] Chosen EGL config details: id:   9 rgba: 8 8 8 0 buf: 24 dep:  0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[    6.372861] [WLAN_RFKILL]: rockchip_wifi_power: 0
[09:00:47.570] Output DSI-1 (crtc 93) video modes:
[    6.372868] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
               1024x600@60.8, preferred, current, 51.0 MHz
[    6.372874] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[09:00:47.570] associating input device event3 with output DSI-1 (none by udev)
[    6.372881] [WLAN_RFKILL]: wifi shut off power [GPIO-1-1]
[09:00:47.570] associating input device event0 with output DSI-1 (none by udev)
[    6.377829] dwc3 fcc00000.dwc3: device reset
[09:00:47.570] associating input device event2 with output DSI-1 (none by udev)
[    6.383786] [dhd] wifi_platform_set_power = 0, sleep done: 10 msec
[09:00:47.570] associating input device event4 with output DSI-1 (none by udev)
[    6.383813] [dhd] [wlan0] wl_android_wifi_off : out
[09:00:47.570] associating input device event1 with output DSI-1 (none by udev)
[    6.384680] [dhd] Register interface [wlan1]  MAC: 72:f7:54:9a:5f:9a
[09:00:47.570] Output 'DSI-1' enabled with head(s) DSI-1
[    6.384680] 
could not load cursor 'dnd-move'
[    6.384713] [dhd] wl_android_post_init: 0
could not load cursor 'dnd-move'
[    6.384721] [dhd] dhdsdio_probe : mutex is released.
could not load cursor 'dnd-copy'
[    6.385416] [dhd] bcmsdh_sdmmc_probe: Enter num=3
could not load cursor 'dnd-none'
[    6.386620] [dhd] _dhd_module_init: Exit err=0
could not load cursor 'dnd-copy'
[    6.414439] [dhd] dhd_pri_open : no mutex held
could not load cursor 'dnd-none'
[    6.414470] [dhd] dhd_pri_open : set mutex lock
Successfully init Wi-Fi for AP625X!
[    6.414480] [dhd] [wlan0] dhd_open : Enter
Successfully initialized wpa_supplicant
[    6.414488] [dhd] Dongle Host Driver, version 101.10.591.52.27 (20240409-1)(20240411-2)(d83d8d7)
xkbcommon: ERROR: couldn't find a Compose file for locale "en_US.UTF-8" (mapped to "en_US.UTF-8")
[    6.414488] /home/viewpro/RK3566_RK3568_Linux5.10_V1.2.0/external/rkwifibt/drivers/bcmdhd compiled on Nov  1 2024 at 12:42:22
could not create XKB compose table for locale 'en_US.UTF-8'.  Disabiling compose
[    6.414488] 
xkbcommon: ERROR: couldn't find a Compose file for locale "en_US.UTF-8" (mapped to "en_US.UTF-8")
[    6.414506] [dhd] dhd_open: ######### called for ifidx=0 #########
could not create XKB compose table for locale 'en_US.UTF-8'.  Disabiling compose
[    6.414523] [dhd] [wlan0] wl_android_wifi_on : in g_wifi_on=0
[    6.414533] [dhd] wifi_platform_set_power = 1, delay: 200 msec
[    6.414540] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ========
[    6.414547] [WLAN_RFKILL]: rockchip_wifi_power: 1
[    6.414554] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[    6.414562] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0]
[    6.444079] android_work: sent uevent USB_STATE=CONNECTED
[    6.449173] android_work: sent uevent USB_STATE=CONFIGURED
[    6.620459] [dhd] wifi_platform_set_power = 1, sleep done: 200 msec
[    6.620494] [dhd] sdio_sw_reset: call mmc_hw_reset
[    6.840630] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[    6.886664] mmc3: queuing unknown CIS tuple 0x80 (2 bytes)
[    6.888546] mmc3: queuing unknown CIS tuple 0x80 (3 bytes)
[    6.890344] mmc3: queuing unknown CIS tuple 0x80 (3 bytes)
[    6.893561] mmc3: queuing unknown CIS tuple 0x80 (7 bytes)
[    6.897295] mmc3: queuing unknown CIS tuple 0x81 (9 bytes)
[    6.960254] mmc_host mmc3: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
[    6.970860] dwmmc_rockchip fe000000.dwmmc: Successfully tuned phase to 270
[    6.971148] [dhd] sdioh_start: set sd_f2_blocksize 256
[    6.971446] [dhd] dhd_bus_devreset: == Power ON ==
[    6.971563] [dhd] F1 signature read @0x18000000=0x15294345
[    6.975421] [dhd] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9 pkg:0x2
[    6.976681] [dhd] DHD: dongle ram size is set to 819200(orig 819200) at 0x198000
[    6.976778] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN
[09:00:48.724] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[    6.976834] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN
[09:00:48.725] Output 'HDMI-A-1' no heads left, disabling.
[    6.976997] [dhd] dhd_conf_set_path_params : Final fw_path=/vendor/etc/firmware/fw_bcm43456c5_ag.bin
[09:00:48.725] Disabling output HDMI-A-1
[    6.977007] [dhd] dhd_conf_set_path_params : Final nv_path=/vendor/etc/firmware/nvram_ap6256.txt
[09:00:48.745] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[    6.977015] [dhd] dhd_conf_set_path_params : Final clm_path=/vendor/etc/firmware/clm_bcm43456c5_ag.blob
[    6.977022] [dhd] dhd_conf_set_path_params : Final conf_path=/vendor/etc/firmware/config.txt
[    6.978834] [dhd] dhd_os_open_image1: /vendor/etc/firmware/config.txt (240 bytes) open success
[    6.979218] [dhd] dhd_conf_read_pm_params : PM = 0
[    6.979236] [dhd] dhd_conf_read_pm_params : pm_in_suspend = 2
[    6.979249] [dhd] dhd_conf_read_others : keep_alive_period = 120000
[    6.979258] [dhd] dhd_conf_read_others : garp = 1
[    6.979269] [dhd] dhd_conf_read_pm_params : suspend_bcn_li_dtim = 10
[    6.979282] [dhd] dhd_conf_read_others : wl_preinit = pm2_sleep_ret=20
[    6.979294] [dhd] dhd_conf_read_pkt_filter : pkt_filter_del id = 100 102 103 104 105 107 
nl80211: kernel reports: Registration to specific type not supported
[    6.979319] [dhd] dhd_conf_read_pkt_filter : pkt_filter_add[0][] = 142 0 0 77 0xffffffffffffffffffffffffffffff 0x2F6465766963652F77616B6575702F
[    6.979967] [dhd] dhd_os_open_image1: /vendor/etc/firmware/fw_bcm43456c5_ag.bin (628872 bytes) open success
[    6.980293] [dhd] dhd_os_open_image1: /vendor/etc/firmware/fw_bcm43456c5_ag.bin (628872 bytes) open success
[    6.980306] [dhd] dhdsdio_download_code_file Using SINGLE image (size 628872)
[    7.051090] [dhd] dhd_os_open_image1: /vendor/etc/firmware/nvram_ap6256.txt (2732 bytes) open success
[    7.051509] [dhd] #AP6256_NVRAM_V1.4_06112021
[    7.052037] [dhd] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[    7.141798] [dhd] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[    7.142017] [dhd] bcmsdh_oob_intr_register: HW_OOB irq=117 flags=0x4
[    7.143203] [dhd] wlc_ver_major 4, wlc_ver_minor 1
[    7.143230] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 1
[    7.143238] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40
[    7.143893] [dhd] dhd_legacy_preinit_ioctls: use firmware generated mac_address 70:f7:54:9a:5f:9a
[    7.144022] [dhd] dhd_apply_default_clm: Ignore clm file /vendor/etc/firmware/clm_bcm43456c5_ag.blob
[    7.145541] [dhd] Firmware up: op_mode=0x0005, MAC=70:f7:54:9a:5f:9a
[    7.149760] [dhd] dhd_legacy_preinit_ioctls: event_log_max_sets: 40 ret: -23
[    7.152422] [dhd] arp_enable:1 arp_ol:0
[    7.152451] [dhd] dhd_conf_add_pkt_filter : 142 0 0 77 0xffffffffffffffffffffffffffffff 0x2F6465766963652F77616B6575702F
[    7.156539] [dhd]   Driver: 101.10.591.52.27 (20240409-1)(20240411-2)
[    7.156539] [dhd]   Firmware: wl0: Apr  1 2024 13:44:02 version 7.45.96.201 (gdb74b971) FWID 01-fe1c2a99 es7.c5.n4.a3
[    7.156539] [dhd]   CLM: 9.2.9 (2016-02-03 04:34:31) 
[    7.156780] [dhd] dhd_txglom_enable: enable 1
[    7.156791] [dhd] dhd_conf_set_txglom_params : txglom_mode=copy
[    7.156799] [dhd] dhd_conf_set_txglom_params : txglomsize=36, deferred_tx_len=0
[    7.156805] [dhd] dhd_conf_set_txglom_params : txinrx_thres=128, dhd_txminmax=-1
[    7.156812] [dhd] dhd_conf_set_txglom_params : tx_max_offset=0, txctl_tmo_fix=300
[    7.156824] [dhd] dhd_conf_get_disable_proptx : fw_proptx=1, disable_proptx=-1
[    7.157836] [dhd] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
[    7.186698] [dhd] dhd_legacy_preinit_ioctls: Failed to get preserve log # !
[    7.187011] [dhd] dhd_legacy_preinit_ioctls: d3_hostwake_delay IOVAR not present, proceed
[    7.187293] [dhd] dhd_bus_check_srmemsize : srmem_size no need to change.
[    7.209057] [dhd] dhd_conf_set_country : set country CN, revision 38
[    7.211871] [dhd] dhd_conf_set_country : Country code: CN (CN/38)
[    7.218352] [dhd] [wlan0] wl_android_wifi_on : Success
[    7.263378] [dhd] CFG80211-ERROR) init_roam_cache : roamscan_mode iovar failed. -23
[    7.263406] [dhd] CFG80211-ERROR) wl_cfg80211_up : Failed to enable RCC.
[    7.265163] [dhd] [wlan0] dhd_open : Exit ret=0
[    7.265189] [dhd] [wlan0] dhd_pri_open : tx queue started
[    7.265196] [dhd] dhd_pri_open : mutex is released.
[    7.273950] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[    7.349644] [dhd] P2P interface registered
[    7.383555] [BT_RFKILL]: bt shut off power
[    7.398115] [dhd] WLC_E_IF: NO_IF set, event Ignored
[    7.399420] [dhd] P2P interface started
[    7.909725] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host high!
[    7.960448] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host input!
[    7.960510] [BT_RFKILL]: ENABLE UART_RTS
[    8.057496] Freeing drm_logo memory: 1384K
[    8.067072] [BT_RFKILL]: DISABLE UART_RTS
[    8.067135] [BT_RFKILL]: bt turn on power
[    8.067291] [BT_RFKILL]: Request irq for bt wakeup host
[    8.067723] [BT_RFKILL]: ** disable irq
[09:00:49.763] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
               Supported EOTF modes: SDR
[09:00:49.763] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:49.763] HDMI-A-1 using at least 2 buffers
[09:00:49.763] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:00:49.763] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:00:49.764] Chosen EGL config details: id:   9 rgba: 8 8 8 0 buf: 24 dep:  0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:00:49.764] Output HDMI-A-1 (crtc 71) video modes:
               1920x1080@60.0, preferred, current, 148.5 MHz
               1920x1080@60.0 16:9, 148.5 MHz
               1920x1080@59.9 16:9, 148.4 MHz
               1920x1080i@60.0, 74.2 MHz
               1920x1080i@60.0 16:9, 74.2 MHz
               1920x1080i@59.9 16:9, 74.2 MHz
               1920x1080@50.0 16:9, 148.5 MHz
               1920x1080i@50.0 16:9, 74.2 MHz
               1680x1050@59.9, 119.0 MHz
               1400x1050@59.9, 101.0 MHz
               1600x900@60.0, 108.0 MHz
               1280x1024@75.0, 135.0 MHz
               1280x1024@60.0, 108.0 MHz
               1440x900@59.9, 88.8 MHz
               1280x800@59.9, 71.0 MHz
               1152x864@75.0, 108.0 MHz
               1280x720@60.0, 74.2 MHz
               1280x720@60.0 16:9, 74.2 MHz
               1280x720@59.9 16:9, 74.2 MHz
               1280x720@50.0 16:9, 74.2 MHz
               1024x768@75.0, 78.8 MHz
               1024x768@60.0, 65.0 MHz
               800x600@75.0, 49.5 MHz
               800x600@60.3, 40.0 MHz
               720x576@50.0 16:9, 27.0 MHz
               720x480@60.0 4:3, 27.0 MHz
               720x480@60.0 16:9, 27.0 MHz
               720x480@59.9, 27.0 MHz
               720x480@59.9 16:9, 27.0 MHz
               640x480@75.0, 31.5 MHz
               640x480@60.0 4:3, 25.2 MHz
[    8.479918] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
               640x480@59.9, 25.2 MHz
               640x480@59.9 4:3, 25.2 MHz
               720x400@70.1, 28.3 MHz
[09:00:49.764] Output HDMI-A-1 changed to mirror output
[09:00:49.764] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
###AMPAK FW Auto detection patch version = [v1.1 20161117]###
FW folder path = /lib/firmware
[    8.593371] of_dma_request_slave_channel: dma-names property of node '/serial@fe650000' missing or empty
proc_reset[    8.593408] dw-apb-uart fe650000.serial: failed to request DMA, use interrupt mode
chip id = BCM4345C5
FW path = /lib/firmware/BCM4345C5.hcd
send hci_download_minidriver[09:00:51.170] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[    9.719573] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[09:00:51.170] Output 'HDMI-A-1' no heads left, disabling.
[09:00:51.170] Disabling output HDMI-A-1
[09:00:51.198] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
proc_resetDone setting line discpline
Successfully init BT for AP625X!
Done
[09:00:52.208] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
               Supported EOTF modes: SDR
[09:00:52.208] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:52.208] HDMI-A-1 using at least 2 buffers
[09:00:52.208] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:00:52.208] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:00:52.209] Chosen EGL config details: id:   9 rgba: 8 8 8 0 buf: 24 dep:  0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:00:52.209] Output HDMI-A-1 (crtc 71) video modes:
               1920x1080@60.0, preferred, current, 148.5 MHz
               1920x1080@60.0 16:9, 148.5 MHz
               1920x1080@59.9 16:9, 148.4 MHz
               1920x1080i@60.0, 74.2 MHz
               1920x1080i@60.0 16:9, 74.2 MHz
               1920x1080i@59.9 16:9, 74.2 MHz
               1920x1080@50.0 16:9, 148.5 MHz
               1920x1080i@50.0 16:9, 74.2 MHz
               1680x1050@59.9, 119.0 MHz
               1400x1050@59.9, 101.0 MHz
               1600x900@60.0, 108.0 MHz
               1280x1024@75.0, 135.0 MHz
               1280x1024@60.0, 108.0 MHz
               1440x900@59.9, 88.8 MHz
               1280x800@59.9, 71.0 MHz
               1152x864@75.0, 108.0 MHz
               1280x720@60.0, 74.2 MHz
               1280x720@60.0 16:9, 74.2 MHz
               1280x720@59.9 16:9, 74.2 MHz
               1280x720@50.0 16:9, 74.2 MHz
               1024x768@75.0, 78.8 MHz
               1024x768@60.0, 65.0 MHz
               800x600@75.0, 49.5 MHz
               800x600@60.3, 40.0 MHz
               720x576@50.0 16:9, 27.0 MHz
               720x480@60.0 4:3, 27.0 MHz
               720x480@60.0 16:9, 27.0 MHz
               720x480@59.9, 27.0 MHz
               720x480@59.9 16:9, 27.0 MHz
               640x480@75.0, 31.5 MHz
[   10.923781] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
               640x480@60.0 4:3, 25.2 MHz
               640x480@59.9, 25.2 MHz
               640x480@59.9 4:3, 25.2 MHz
               720x400@70.1, 28.3 MHz
[09:00:52.209] Output HDMI-A-1 changed to mirror output
[09:00:52.209] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[09:00:53.630] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[   12.179513] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[09:00:53.630] Output 'HDMI-A-1' no heads left, disabling.
[09:00:53.630] Disabling output HDMI-A-1
[09:00:53.659] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:54.669] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
               Supported EOTF modes: SDR
[09:00:54.670] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:54.670] HDMI-A-1 using at least 2 buffers
[09:00:54.670] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:00:54.670] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:00:54.670] Chosen EGL config details: id:   9 rgba: 8 8 8 0 buf: 24 dep:  0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:00:54.670] Output HDMI-A-1 (crtc 71) video modes:
               1920x1080@60.0, preferred, current, 148.5 MHz
               1920x1080@60.0 16:9, 148.5 MHz
               1920x1080@59.9 16:9, 148.4 MHz
               1920x1080i@60.0, 74.2 MHz
               1920x1080i@60.0 16:9, 74.2 MHz
               1920x1080i@59.9 16:9, 74.2 MHz
               1920x1080@50.0 16:9, 148.5 MHz
               1920x1080i@50.0 16:9, 74.2 MHz
               1680x1050@59.9, 119.0 MHz
               1400x1050@59.9, 101.0 MHz
               1600x900@60.0, 108.0 MHz
               1280x1024@75.0, 135.0 MHz
               1280x1024@60.0, 108.0 MHz
               1440x900@59.9, 88.8 MHz
               1280x800@59.9, 71.0 MHz
               1152x864@75.0, 108.0 MHz
               1280x720@60.0, 74.2 MHz
               1280x720@60.0 16:9, 74.2 MHz
               1280x720@59.9 16:9, 74.2 MHz
               1280x720@50.0 16:9, 74.2 MHz
               1024x768@75.0, 78.8 MHz
               1024x768@60.0, 65.0 MHz
               800x600@75.0, 49.5 MHz
               800x600@60.3, 40.0 MHz
               720x576@50.0 16:9, 27.0 MHz
               720x480@60.0 4:3, 27.0 MHz
               720x480@60.0 16:9, 27.0 MHz
               720x480@59.9, 27.0 MHz
               720x480@59.9 16:9, 27.0 MHz
               640x480@75.0, 31.5 MHz
               640x480@60.0 4:3, 25.2 MHz
[   13.386635] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
               640x480@59.9, 25.2 MHz
               640x480@59.9 4:3, 25.2 MHz
               720x400@70.1, 28.3 MHz
[09:00:54.671] Output HDMI-A-1 changed to mirror output
[09:00:54.671] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[09:00:56.077] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[   14.626187] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[09:00:56.077] Output 'HDMI-A-1' no heads left, disabling.
[09:00:56.077] Disabling output HDMI-A-1
[09:00:56.105] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:57.116] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
               Supported EOTF modes: SDR
[09:00:57.117] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:57.117] HDMI-A-1 using at least 2 buffers
[09:00:57.117] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:00:57.117] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:00:57.117] Chosen EGL config details: id:   9 rgba: 8 8 8 0 buf: 24 dep:  0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:00:57.117] Output HDMI-A-1 (crtc 71) video modes:
               1920x1080@60.0, preferred, current, 148.5 MHz
               1920x1080@60.0 16:9, 148.5 MHz
               1920x1080@59.9 16:9, 148.4 MHz
               1920x1080i@60.0, 74.2 MHz
               1920x1080i@60.0 16:9, 74.2 MHz
               1920x1080i@59.9 16:9, 74.2 MHz
               1920x1080@50.0 16:9, 148.5 MHz
               1920x1080i@50.0 16:9, 74.2 MHz
               1680x1050@59.9, 119.0 MHz
               1400x1050@59.9, 101.0 MHz
               1600x900@60.0, 108.0 MHz
               1280x1024@75.0, 135.0 MHz
               1280x1024@60.0, 108.0 MHz
               1440x900@59.9, 88.8 MHz
               1280x800@59.9, 71.0 MHz
               1152x864@75.0, 108.0 MHz
               1280x720@60.0, 74.2 MHz
               1280x720@60.0 16:9, 74.2 MHz
               1280x720@59.9 16:9, 74.2 MHz
               1280x720@50.0 16:9, 74.2 MHz
               1024x768@75.0, 78.8 MHz
               1024x768@60.0, 65.0 MHz
               800x600@75.0, 49.5 MHz
               800x600@60.3, 40.0 MHz
               720x576@50.0 16:9, 27.0 MHz
               720x480@60.0 4:3, 27.0 MHz
               720x480@60.0 16:9, 27.0 MHz
               720x480@59.9, 27.0 MHz
               720x480@59.9 16:9, 27.0 MHz
               640x480@75.0, 31.5 MHz
               640x480@60.0 4:3, 25.2 MHz
[   15.832472] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
               640x480@59.9, 25.2 MHz
               640x480@59.9 4:3, 25.2 MHz
               720x400@70.1, 28.3 MHz
[09:00:57.118] Output HDMI-A-1 changed to mirror output
[09:00:57.118] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[09:00:58.537] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[   17.086164] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[09:00:58.537] Output 'HDMI-A-1' no heads left, disabling.
[09:00:58.537] Disabling output HDMI-A-1
[09:00:58.567] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:59.576] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
               Supported EOTF modes: SDR
[09:00:59.576] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:00:59.576] HDMI-A-1 using at least 2 buffers
[09:00:59.577] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:00:59.577] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:00:59.577] Chosen EGL config details: id:   9 rgba: 8 8 8 0 buf: 24 dep:  0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:00:59.577] Output HDMI-A-1 (crtc 71) video modes:
               1920x1080@60.0, preferred, current, 148.5 MHz
               1920x1080@60.0 16:9, 148.5 MHz
               1920x1080@59.9 16:9, 148.4 MHz
               1920x1080i@60.0, 74.2 MHz
               1920x1080i@60.0 16:9, 74.2 MHz
               1920x1080i@59.9 16:9, 74.2 MHz
               1920x1080@50.0 16:9, 148.5 MHz
               1920x1080i@50.0 16:9, 74.2 MHz
               1680x1050@59.9, 119.0 MHz
               1400x1050@59.9, 101.0 MHz
               1600x900@60.0, 108.0 MHz
               1280x1024@75.0, 135.0 MHz
               1280x1024@60.0, 108.0 MHz
               1440x900@59.9, 88.8 MHz
               1280x800@59.9, 71.0 MHz
               1152x864@75.0, 108.0 MHz
               1280x720@60.0, 74.2 MHz
               1280x720@60.0 16:9, 74.2 MHz
               1280x720@59.9 16:9, 74.2 MHz
               1280x720@50.0 16:9, 74.2 MHz
               1024x768@75.0, 78.8 MHz
               1024x768@60.0, 65.0 MHz
               800x600@75.0, 49.5 MHz
               800x600@60.3, 40.0 MHz
               720x576@50.0 16:9, 27.0 MHz
               720x480@60.0 4:3, 27.0 MHz
               720x480@60.0 16:9, 27.0 MHz
               720x480@59.9, 27.0 MHz
               720x480@59.9 16:9, 27.0 MHz
               640x480@75.0, 31.5 MHz
[   18.292004] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
               640x480@60.0 4:3, 25.2 MHz
               640x480@59.9, 25.2 MHz
               640x480@59.9 4:3, 25.2 MHz
               720x400@70.1, 28.3 MHz
[09:00:59.577] Output HDMI-A-1 changed to mirror output
[09:00:59.578] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[09:01:00.983] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[   19.532876] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[09:01:00.984] Output 'HDMI-A-1' no heads left, disabling.
[09:01:00.984] Disabling output HDMI-A-1
[09:01:01.010] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:01:02.020] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
               Supported EOTF modes: SDR
[09:01:02.021] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:01:02.021] HDMI-A-1 using at least 2 buffers
[09:01:02.021] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:01:02.021] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:01:02.021] Chosen EGL config details: id:   9 rgba: 8 8 8 0 buf: 24 dep:  0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:01:02.021] Output HDMI-A-1 (crtc 71) video modes:
               1920x1080@60.0, preferred, current, 148.5 MHz
               1920x1080@60.0 16:9, 148.5 MHz
               1920x1080@59.9 16:9, 148.4 MHz
               1920x1080i@60.0, 74.2 MHz
               1920x1080i@60.0 16:9, 74.2 MHz
               1920x1080i@59.9 16:9, 74.2 MHz
               1920x1080@50.0 16:9, 148.5 MHz
               1920x1080i@50.0 16:9, 74.2 MHz
               1680x1050@59.9, 119.0 MHz
               1400x1050@59.9, 101.0 MHz
               1600x900@60.0, 108.0 MHz
               1280x1024@75.0, 135.0 MHz
               1280x1024@60.0, 108.0 MHz
               1440x900@59.9, 88.8 MHz
               1280x800@59.9, 71.0 MHz
               1152x864@75.0, 108.0 MHz
               1280x720@60.0, 74.2 MHz
               1280x720@60.0 16:9, 74.2 MHz
               1280x720@59.9 16:9, 74.2 MHz
               1280x720@50.0 16:9, 74.2 MHz
               1024x768@75.0, 78.8 MHz
               1024x768@60.0, 65.0 MHz
               800x600@75.0, 49.5 MHz
               800x600@60.3, 40.0 MHz
               720x576@50.0 16:9, 27.0 MHz
               720x480@60.0 4:3, 27.0 MHz
               720x480@60.0 16:9, 27.0 MHz
               720x480@59.9, 27.0 MHz
               720x480@59.9 16:9, 27.0 MHz
               640x480@75.0, 31.5 MHz
               640x480@60.0 4:3, 25.2 MHz
[   20.737984] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
               640x480@59.9, 25.2 MHz
               640x480@59.9 4:3, 25.2 MHz
               720x400@70.1, 28.3 MHz
[09:01:02.022] Output HDMI-A-1 changed to mirror output
[09:01:02.022] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[09:01:03.820] DRM: head 'HDMI-A-1' updated, connector 164 is disconnected.
[   22.369490] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[09:01:03.820] Output 'HDMI-A-1' no heads left, disabling.
[09:01:03.820] Disabling output HDMI-A-1
[09:01:03.840] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:01:04.859] DRM: head 'HDMI-A-1' updated, connector 164 is connected, EDID make 'GSM', model '27MP35', serial ''
               Supported EOTF modes: SDR
[09:01:04.860] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[09:01:04.860] HDMI-A-1 using at least 2 buffers
[09:01:04.860] Output 'HDMI-A-1' attempts EOTF mode: SDR
[09:01:04.860] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[09:01:04.860] Chosen EGL config details: id:   9 rgba: 8 8 8 0 buf: 24 dep:  0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[09:01:04.860] Output HDMI-A-1 (crtc 71) video modes:
               1920x1080@60.0, preferred, current, 148.5 MHz
               1920x1080@60.0 16:9, 148.5 MHz
               1920x1080@59.9 16:9, 148.4 MHz
               1920x1080i@60.0, 74.2 MHz
               1920x1080i@60.0 16:9, 74.2 MHz
               1920x1080i@59.9 16:9, 74.2 MHz
               1920x1080@50.0 16:9, 148.5 MHz
               1920x1080i@50.0 16:9, 74.2 MHz
               1680x1050@59.9, 119.0 MHz
               1400x1050@59.9, 101.0 MHz
               1600x900@60.0, 108.0 MHz
               1280x1024@75.0, 135.0 MHz
               1280x1024@60.0, 108.0 MHz
               1440x900@59.9, 88.8 MHz
               1280x800@59.9, 71.0 MHz
               1152x864@75.0, 108.0 MHz
               1280x720@60.0, 74.2 MHz
               1280x720@60.0 16:9, 74.2 MHz
               1280x720@59.9 16:9, 74.2 MHz
               1280x720@50.0 16:9, 74.2 MHz
               1024x768@75.0, 78.8 MHz
               1024x768@60.0, 65.0 MHz
               800x600@75.0, 49.5 MHz
               800x600@60.3, 40.0 MHz
               720x576@50.0 16:9, 27.0 MHz
               720x480@60.0 4:3, 27.0 MHz
               720x480@60.0 16:9, 27.0 MHz
               720x480@59.9, 27.0 MHz
               720x480@59.9 16:9, 27.0 MHz
               640x480@75.0, 31.5 MHz
               640x480@60.0 4:3, 25.2 MHz
[   23.577237] rockchip-vop2 fe040000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
               640x480@59.9, 25.2 MHz
               640x480@59.9 4:3, 25.2 MHz
               720x400@70.1, 28.3 MHz
[09:01:04.861] Output HDMI-A-1 changed to mirror output
[09:01:04.861] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[   33.923794] vcc3v3_lcd1_n: disabling
    /bin/list-iodomain.sh version: V1.0.1 
    Get CHIP ID: rk356x 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    XXXXXXXXXX      PLEASE CHECK IO-DOMAIN !!!!!!!!!!!!!!! 
    XXXXXXXXXX        请务必检查IO电源域配置  !!!!!!!!!!!!!!! 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    Get IO DOMAIN VALUE: 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    注意事项:PMUIO1/PMUIO2 固定不可配 
    VCCIO2电平由硬件FLASH_VOL_SEL决定: 
    当VCCIo2供电是1.8V,则FLASH_VOL_SEL管脚必须保持为高电平; 
    当VCCIO2供电是3.3V,则FLASH_VOL_SEL管脚必须保持为低电平; 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    pmuio2_vsel: 3.3V 
    vccio7_vsel: 3.3V 
    vccio6_vsel: 1.8V 
    vccio5_vsel: 3.3V 
    vccio4_vsel: 3.3V 
    vccio3_vsel: 3.3V 
    vccio2_vsel: 3.3V 
    vccio1_vsel: 3.3V 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 

root@rk3566-buildroot:/# 
root@rk3566-buildroot:/# 
root@rk3566-buildroot:/#     /bin/list-iodomain.sh version: V1.0.1 
    Get CHIP ID: rk356x 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    XXXXXXXXXX      PLEASE CHECK IO-DOMAIN !!!!!!!!!!!!!!! 
    XXXXXXXXXX        请务必检查IO电源域配置  !!!!!!!!!!!!!!! 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    Get IO DOMAIN VALUE: 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    注意事项:PMUIO1/PMUIO2 固定不可配 
    VCCIO2电平由硬件FLASH_VOL_SEL决定: 
    当VCCIo2供电是1.8V,则FLASH_VOL_SEL管脚必须保持为高电平; 
    当VCCIO2供电是3.3V,则FLASH_VOL_SEL管脚必须保持为低电平; 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    pmuio2_vsel: 3.3V 
    vccio7_vsel: 3.3V 
    vccio6_vsel: 1.8V 
    vccio5_vsel: 3.3V 
    vccio4_vsel: 3.3V 
    vccio3_vsel: 3.3V 
    vccio2_vsel: 3.3V 
    vccio1_vsel: 3.3V 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    /bin/list-iodomain.sh version: V1.0.1 
    Get CHIP ID: rk356x 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    XXXXXXXXXX      PLEASE CHECK IO-DOMAIN !!!!!!!!!!!!!!! 
    XXXXXXXXXX        请务必检查IO电源域配置  !!!!!!!!!!!!!!! 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    Get IO DOMAIN VALUE: 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    注意事项:PMUIO1/PMUIO2 固定不可配 
    VCCIO2电平由硬件FLASH_VOL_SEL决定: 
    当VCCIo2供电是1.8V,则FLASH_VOL_SEL管脚必须保持为高电平; 
    当VCCIO2供电是3.3V,则FLASH_VOL_SEL管脚必须保持为低电平; 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 
    pmuio2_vsel: 3.3V 
    vccio7_vsel: 3.3V 
    vccio6_vsel: 1.8V 
    vccio5_vsel: 3.3V 
    vccio4_vsel: 3.3V 
    vccio3_vsel: 3.3V 
    vccio2_vsel: 3.3V 
    vccio1_vsel: 3.3V 
    XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 

root@rk3566-buildroot:/# 
root@rk3566-buildroot:/# 

[END] 2024/11/2 9:47:19
 

本文来自互联网用户投稿,该文观点仅代表作者本人,不代表本站立场。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如若转载,请注明出处:http://www.rhkb.cn/news/462271.html

如若内容造成侵权/违法违规/事实不符,请联系长河编程网进行投诉反馈email:809451989@qq.com,一经查实,立即删除!

相关文章

ctfshow文件包含web78~81

目录 web78 方法一&#xff1a;filter伪协议 方法二&#xff1a;input协议 方法三&#xff1a;data协议 web79 方法一:input协议 方法二&#xff1a;data协议 web80 方法一&#xff1a;input协议 方法二&#xff1a;日志包含getshell web81 web78 if(isset($_GET[file]…

电能表预付费系统-标准传输规范(STS)(30)

6.5.3.2 CONTROLBlock construction The 1 6 digit CONTROLBlock is constructed from the data elements in the APDU as defined in Table 36 and Table 37.The most significant digit is in position 1 5 and the least significant digit in position 0. APDU中的数据元素…

基于YOLO11/v10/v8/v5深度学习的维修工具检测识别系统设计与实现【python源码+Pyqt5界面+数据集+训练代码】

《博主简介》 小伙伴们好&#xff0c;我是阿旭。专注于人工智能、AIGC、python、计算机视觉相关分享研究。 ✌更多学习资源&#xff0c;可关注公-仲-hao:【阿旭算法与机器学习】&#xff0c;共同学习交流~ &#x1f44d;感谢小伙伴们点赞、关注&#xff01; 《------往期经典推…

人工智能基础-opencv-图像处理篇

一.图像预处理 图像翻转 cv2.flip 是 OpenCV 库中的一个函数&#xff0c;用于翻转图像。翻转可以是水平翻转、垂直翻转或同时水平和垂直翻转。这个函数接受两个参数&#xff1a;要翻转的图像和一个指定翻转类型的标志。 img cv2.imread(../images/car2.png) #翻转 0&#xf…

Hive学习笔记

1 Hive基本概念 1.1 Hive定义 Hive&#xff1a;由 Facebook 开源用于解决海量结构化日志的数据统计工具。 Hive 是基于 Hadoop 的一个数据仓库工具&#xff0c;可以将结构化的数据文件映射为一张表&#xff0c;并 提供类 SQL 查询功能。 利用MapReduce去查询数据文件中的某些内…

用图说明 CPU、MCU、MPU、SoC 的区别

CPU CPU 负责执行构成计算机程序的指令&#xff0c;执行这些指令所指定的算术、逻辑、控制和输入/输出&#xff08;I/O&#xff09;操作。 MCU (microcontroller unit) 不同的 MCU 架构如下&#xff0c;注意这里的 MPU 表示 memory protection unit MPU (microprocessor un…

HTML 语法规范——代码注释、缩进与格式、标签与属性、字符编码等

文章目录 一、代码注释1.1 使用注释的主要目的1.2 使用建议二、标签的使用2.1 开始标签和结束标签2.2 自闭合标签2.3 标签的嵌套2.4 标签的有效性三、属性四、缩进与格式4.1 一致的缩进4.2 元素单独占用一行4.3 嵌套元素的缩进4.4 避免冗长的行五、字符编码六、小结在开发 HTML…

虚拟现实与增强现实:重塑娱乐和教育的边界!

内容概要 在这个瞬息万变的时代&#xff0c;虚拟现实&#xff08;VR&#xff09;和增强现实&#xff08;AR&#xff09;正如两位魔法师&#xff0c;腾云驾雾间掀起了一场教育与娱乐的革命。虚拟现实带我们飞跃平凡&#xff0c;进入一个充满奇迹的数字宇宙&#xff0c;仿佛我们…

中仕公考:上海市25年公务员考试今日报名

2025年上海市公务员考试于今日开始报名 考试报名采取网络报名方式进行&#xff0c;报考者可在2024年11月2日0:00至11月8日12:00期间登录专题网站进行报名。 年龄在18周岁以上&#xff0c;35周岁以下(1988年11月至2006年11月期间出生)&#xff0c;应届硕士、博士研究生报考的&…

Diving into the STM32 HAL-----HAL_GPIO

1、怎么看待外设&#xff1a; 从总线连接的角度看&#xff0c;外设和Core、DMA通过总线交换数据&#xff0c;正所谓要想富先修路。要注意&#xff0c;这些总线中的每一个都连接到不同的时钟源&#xff0c;这些时钟源决定了连接到该总线的外设操作的最大速度。 从内存分配的角度…

【表格解决问题】EXCEL行数过多,WPS如何按逐行分别打印多个纸张中

1 问题描述 如图&#xff1a;我的表格行数太多了。打印在一张纸上有点不太好看 2 解决方式 Step01&#xff1a;先选中你需要打印的部分&#xff0c;找到【页面】->【打印区域】->【设置打印区域】 Step02&#xff1a;先选中一行&#xff0c;找到【插入分页符】 Step0…

提升安全上网体验:Windows 11 启用 DOH(阿里公共DNS)

文章目录 阿里公共 DNS 介绍免费开通云解析 DNS 服务Windows 编辑 DNS 设置配置 IPv4配置 IPv6 路由器配置 DNS 阿里公共 DNS 介绍 https://alidns.com/ 免费开通云解析 DNS 服务 https://dnsnext.console.aliyun.com/pubDNS 开通服务后&#xff0c;获取 DOH 模板&#xff0…

如何在Linux下部署自己的ZFile开源网盘

ZFile 项目介绍 ZFile是一个功能强大、灵活的开源网盘系统&#xff0c;为用户提供安全便捷的文件存储和共享方案。 项目概述 ZFile由ZFile, Inc.开发和维护&#xff0c;基于Docusaurus构建。其用户友好的界面支持多种文件存储和共享功能&#xff0c;并具备高度的可定制性和扩…

Spring AI : 让ChatGPT成为你构建应用的核心亮点

本文是一篇介绍spring ai的文章&#xff0c;主要介绍了生成文本内容&#xff0c;以及读取图片中内容两个能力。 之所以介绍这两个能力&#xff0c;是因为 大模型目前最适合做的事情有两个&#xff1a; 1&#xff09; 非结构化数据的结构化&#xff08;图片转文字&#xff0c;…

Windows 命令提示符(cmd)中输入 mysql 并收到错误消息“MySQL不是内部或外部命令,也不是可运行的程序或批处理文件?

目录 背景: 过程&#xff1a; 1.找到MySQL安装的路径 2.编辑环境变量 3.打开cmd&#xff0c;输入mysql --version测试成功 总结: 背景: 很早之前安装了Mysql数据库&#xff0c;想查询一下当前安装的MySQL客户端的版本号&#xff0c;我在命令行界面输入mysql --verion命令回…

履带式排爆演习训练机器人技术详解

履带式排爆演习训练机器人是现代反恐、救援及危险环境处理领域中的重要工具。它们结合了先进的机械设计、智能感知、精确控制及高效算法&#xff0c;能够在复杂、危险的环境中执行排爆、侦察、取样等多种高风险任务&#xff0c;极大地保障了人员安全。 技术特点 1. 卓越的地面…

基于SSM医院门诊互联电子病历管理系统的设计

管理员账户功能包括&#xff1a;系统首页&#xff0c;个人中心&#xff0c;用户管理&#xff0c;医生管理&#xff0c;项目分类管理&#xff0c;项目信息管理&#xff0c;预约信息管理&#xff0c;检查信息管理&#xff0c;系统管理 用户账号功能包括&#xff1a;系统首页&…

PVE定时开启关闭虚拟机,实现PVE中群晖虚拟机的定时开机和关闭

如果在PVE中安装了群晖&#xff0c;又不想每天关闭PVE(不在家&#xff0c;怕服务器起不来)&#xff0c;因此想每天定时关闭开启黑群晖和其他虚拟机释放资源。 在网上查了很多&#xff0c;说在crontab添加命令 00 2 * * * pvesh create /nodes/pve/qemu/102/status/stop 00 6 …

【数据结构】宜宾大学-计院-实验六

实验 6 栈和队列&#xff08;综合实验&#xff09; 实验目的&#xff1a;实验内容&#xff1a;进制转换问题&#xff1a;第1题测试结果&#xff1a;第1题代码实现&#xff1a; 括号匹配问题&#xff1a;第2题测试结果&#xff1a;第2题代码实现&#xff1a; 回文字符串问题&…

java并发编程-CAS详解

一定要看这个链接的视频&#xff0c;讲解十分清楚&#xff01;&#xff01;&#xff01; 【【Java并发】面试官问我CAS、乐观锁、悲观锁&#xff0c;我反手就是骑脸输出】 https://www.bilibili.com/video/BV1ff4y1q7we/?share_sourcecopy_web&vd_sourceafbacdc02063c57e7…