瑞萨RZ/G2L平台 初起动(SD卡启动)

文章目录

    • 一 准备条件
      • 1 工具
      • 2 硬件
      • 3 镜像
    • 二 烧录SD卡启动盘
    • 三 写Bootloader
      • 1 烧录文件
      • 2 启动烧录
      • 3 烧录
    • 四 启动设置

一 准备条件

1 工具

** BalenaEtcher(俗称“ Etcher”),是一款快速将系统镜像文件( .iso 或 .img 或 .zip或.wic)刻录到usb等设备的启动盘制作工具。balenaEtcher基于 Electron 框架开发,支持windows,macOs和linux系统。类似的工具还有Win32 Disk Imager等,该工具的下载链接:https://etcher.balena.io/

** Tera Term是一款虚似的终端软件,一般用以全自动实行与从PC进行的远程桌面连接有关的每日任务,适用TCP/IP网络联接和串口通信接口方式,适用SSH/Telnet以及他服务项目,可订制自身的开发语言加上拓展作用。类似的如putty、MobaXterm等,该工具的官方连接:http://www.teraterm.net/(不知什么原因,打不开),可以通过如下连接下载:
https://pan.baidu.com/s/1gW_5PCJzloKoclcaBPXy1Q
提取码:h8ny

2 硬件

** USB type C charger
** USB type C to type C cable
** micro SD UHI-Class10 (8GB or more)
** USB cable (USB Type-A- Micro USB Type-B)
** micro-HDMI to HDMI cable
**

3 镜像

RZ/G2L Pre-built Images (RZG2L_VLP3.0.5_Pre-built_Images_EN.zip)

二 烧录SD卡启动盘

使用BalenaEtcher工具,将Images烧录到SD卡上。即打开工具,依次选择添加镜像–》选择SD卡–》启动烧录
在这里插入图片描述
最后烧录成功显示如下
在这里插入图片描述

三 写Bootloader

1 烧录文件

SD卡烧录成功后,在boot分区会有如下几样东西,其中3样(lash_Writer_SCIF_RZG2L_SMARC_PMIC_DDR4_2GB_1PCS.mot, bl2_bp-smarc-rzg2l_pmic.srec and fip-smarc-rzg2l_pmic.srec)是要通过Tera Term经串口烧录到系统中
在这里插入图片描述

2 启动烧录

RZ/G2L参考板的硬件大体如下所示,连接对应的接线后,做如下操作,进入烧录模式:
1)上电(CN6),此时 LED1(VBUS Power ON) and LED3 (Module PWR On) 2个LED点亮
2)确认SW11设置为OFF/ON/OFF/ON和SW1设置为ON/OFF
3)长按SW9 大约2s,LED4(Carrier PWR On)点亮
在这里插入图片描述
![在这里插入图片描述](https://img-blog.csdnimg.cn/4a2d425b44bb41cabe424b1c7e4e4048.png
4)打开 Tera Term软件,设置串口参数如下

Baud rate : 115200
Date : 8 bit
Parity : none
Stop : 1 bit
Flow control : none

5)点按SW10,进入烧录模式,Tera Term会输出如下信息
在这里插入图片描述

3 烧录

1)通过 Tera Term软件的 “File” > “Send file”,依次选择要烧录的文件烧录
2)如下是选择文件
在这里插入图片描述

3)如下是烧录过程
在这里插入图片描述

4 )如下是完整的烧录过程打印
在这里插入图片描述

四 启动设置

1)Please change the SW11 as below (SW11-2 ON→OFF).
在这里插入图片描述

2)Insert your microSD card to the slot (CN10) on the carry board.
在这里插入图片描述

3)Turn on the power of the board by pressing the power button SW9.此时,启动会失败
在这里插入图片描述
重新设置环境变量,正常启动
在这里插入图片描述
4)完整的启动打印,启动后,显示weston界面

NOTICE:  BL2: v2.9(release):c314a39-dirty
[11-04-54.895]NOTICE:  BL2: Built : 14:49:18, Sep 19 2023
[11-04-54.936]NOTICE:  BL2: Booting BL31
[11-04-54.937]NOTICE:  BL31: v2.9(release):c314a39-dirty
[11-04-54.937]NOTICE:  BL31: Built : 14:49:18, Sep 19 2023
[11-04-55.040]
[11-04-55.040]
[11-04-55.040]U-Boot 2021.10 (Sep 20 2023 - 02:21:30 +0000)
[11-04-55.040]
[11-04-55.040]CPU:   Renesas Electronics CPU rev 1.0
[11-04-55.040]Model: smarc-rzg2l
[11-04-55.153]DRAM:  1.9 GiB
[11-04-55.231]WDT:   watchdog@0000000012800800
[11-04-55.231]WDT:   Started with servicing (60s timeout)
[11-04-55.231]MMC:   sd@11c00000: 0, sd@11c10000: 1
[11-04-56.088]Loading Environment from MMC... OK
[11-04-56.106]In:    serial@1004b800
[11-04-56.107]Out:   serial@1004b800
[11-04-56.107]Err:   serial@1004b800
[11-04-56.107]U-boot WDT started!
[11-04-56.164]Net:   
[11-04-56.164]Error: ethernet@11c20000 address not set.
[11-04-56.164]No ethernet found.
[11-04-56.164]
[11-04-58.165]Hit any key to stop autoboot:  0 
[11-04-58.165]## Resetting to default environment
[11-04-58.325]switch to partitions #0, OK
[11-04-58.325]mmc1 is current device
[11-04-59.908]20068864 bytes read in 1579 ms (12.1 MiB/s)
[11-04-59.935]38594 bytes read in 6 ms (6.1 MiB/s)
[11-04-59.935]Error: Bad gzipped data
[11-04-59.935]Moving Image from 0x48080000 to 0x48200000, end=495a0000
[11-05-00.029]## Flattened Device Tree blob at 48000000
[11-05-00.029]   Booting using the fdt blob at 0x48000000
[11-05-00.030]   Loading Device Tree to 0000000057ff3000, end 0000000057fff6c1 ... OK
[11-05-00.030]
[11-05-00.035]Starting kernel ...
[11-05-00.035]
[11-05-00.132][    0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[11-05-00.132][    0.000000] Linux version 5.10.184-cip36-yocto-standard (oe-user@oe-host) (aarch64-poky-linux-gcc (GCC) 8.3.0, GNU ld (GNU Binutils) 2.31.1) #1 SMP PREEMPT Tue Apr 5 23:00:00 UTC 2011
[11-05-00.133][    0.000000] Machine model: Renesas SMARC EVK based on r9a07g044l2
[11-05-00.133][    0.000000] earlycon: scif0 at MMIO 0x000000001004b800 (options '115200n8')
[11-05-00.133][    0.000000] printk: bootconsole [scif0] enabled
[11-05-00.133][    0.000000] efi: UEFI not found.
[11-05-00.133][    0.000000] Reserved memory: created CMA memory pool at 0x0000000058000000, size 256 MiB
[11-05-00.134][    0.000000] OF: reserved mem: initialized node linux,cma@58000000, compatible id shared-dma-pool
[11-05-00.136][    0.000000] Reserved memory: created CMA memory pool at 0x0000000068000000, size 128 MiB
[11-05-00.136][    0.000000] OF: reserved mem: initialized node linux,multimedia, compatible id shared-dma-pool
[11-05-00.152][    0.000000] Zone ranges:
[11-05-00.190][    0.000000]   DMA      [mem 0x0000000048000000-0x00000000bfffffff]
[11-05-00.190][    0.000000]   DMA32    empty
[11-05-00.190][    0.000000]   Normal   empty
[11-05-00.190][    0.000000] Movable zone start for each node
[11-05-00.190][    0.000000] Early memory node ranges
[11-05-00.194][    0.000000]   node   0: [mem 0x0000000048000000-0x00000000bfffffff]
[11-05-00.194][    0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x00000000bfffffff]
[11-05-00.304][    0.000000] psci: probing for conduit method from DT.
[11-05-00.304][    0.000000] psci: PSCIv1.1 detected in firmware.
[11-05-00.304][    0.000000] psci: Using standard PSCI v0.2 function IDs
[11-05-00.305][    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[11-05-00.305][    0.000000] psci: SMC Calling Convention v1.2
[11-05-00.305][    0.000000] percpu: Embedded 23 pages/cpu s55896 r8192 d30120 u94208
[11-05-00.306][    0.000000] Detected VIPT I-cache on CPU0
[11-05-00.306][    0.000000] CPU features: detected: GIC system register CPU interface
[11-05-00.306][    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[11-05-00.307][    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 483840
[11-05-00.307][    0.000000] Kernel command line: rw rootwait earlycon root=/dev/mmcblk1p2 wdt_overflow=0
[11-05-00.307][    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[11-05-00.307][    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[11-05-00.308][    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[11-05-00.472][    0.000000] Memory: 1512672K/1966080K available (12608K kernel code, 1102K rwdata, 3664K rodata, 2112K init, 429K bss, 60192K reserved, 393216K cma-reserved)
[11-05-00.472][    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[11-05-00.472][    0.000000] rcu: Preemptible hierarchical RCU implementation.
[11-05-00.473][    0.000000] rcu:     RCU event tracing is enabled.
[11-05-00.473][    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[11-05-00.473][    0.000000]  Trampoline variant of Tasks RCU enabled.
[11-05-00.473][    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[11-05-00.473][    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[11-05-00.473][    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[11-05-00.473][    0.000000] GICv3: 480 SPIs implemented
[11-05-00.473][    0.000000] GICv3: 0 Extended SPIs implemented
[11-05-00.473][    0.000000] GICv3: Distributor has no Range Selector support
[11-05-00.474][    0.000000] GICv3: 16 PPIs implemented
[11-05-00.474][    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000011940000
[11-05-00.474][    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[11-05-00.474][    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[11-05-00.475][    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[11-05-00.476][    0.008228] Console: colour dummy device 80x25
[11-05-00.476][    0.012695] printk: console [tty0] enabled
[11-05-00.476][    0.016812] printk: bootconsole [scif0] disabled
[11-05-02.161][    0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[11-05-02.161][    0.000000] Linux version 5.10.184-cip36-yocto-standard (oe-user@oe-host) (aarch64-poky-linux-gcc (GCC) 8.3.0, GNU ld (GNU Binutils) 2.31.1) #1 SMP PREEMPT Tue Apr 5 23:00:00 UTC 2011
[11-05-02.161][    0.000000] Machine model: Renesas SMARC EVK based on r9a07g044l2
[11-05-02.162][    0.000000] earlycon: scif0 at MMIO 0x000000001004b800 (options '115200n8')
[11-05-02.162][    0.000000] printk: bootconsole [scif0] enabled
[11-05-02.162][    0.000000] efi: UEFI not found.
[11-05-02.162][    0.000000] Reserved memory: created CMA memory pool at 0x0000000058000000, size 256 MiB
[11-05-02.162][    0.000000] OF: reserved mem: initialized node linux,cma@58000000, compatible id shared-dma-pool
[11-05-02.163][    0.000000] Reserved memory: created CMA memory pool at 0x0000000068000000, size 128 MiB
[11-05-02.163][    0.000000] OF: reserved mem: initialized node linux,multimedia, compatible id shared-dma-pool
[11-05-02.163][    0.000000] Zone ranges:
[11-05-02.163][    0.000000]   DMA      [mem 0x0000000048000000-0x00000000bfffffff]
[11-05-02.163][    0.000000]   DMA32    empty
[11-05-02.163][    0.000000]   Normal   empty
[11-05-02.163][    0.000000] Movable zone start for each node
[11-05-02.163][    0.000000] Early memory node ranges
[11-05-02.163][    0.000000]   node   0: [mem 0x0000000048000000-0x00000000bfffffff]
[11-05-02.163][    0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x00000000bfffffff]
[11-05-02.164][    0.000000] psci: probing for conduit method from DT.
[11-05-02.164][    0.000000] psci: PSCIv1.1 detected in firmware.
[11-05-02.164][    0.000000] psci: Using standard PSCI v0.2 function IDs
[11-05-02.165][    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[11-05-02.165][    0.000000] psci: SMC Calling Convention v1.2
[11-05-02.166][    0.000000] percpu: Embedded 23 pages/cpu s55896 r8192 d30120 u94208
[11-05-02.166][    0.000000] Detected VIPT I-cache on CPU0
[11-05-02.166][    0.000000] CPU features: detected: GIC system register CPU interface
[11-05-02.166][    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[11-05-02.166][    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 483840
[11-05-02.166][    0.000000] Kernel command line: rw rootwait earlycon root=/dev/mmcblk1p2 wdt_overflow=0
[11-05-02.167][    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[11-05-02.167][    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[11-05-02.167][    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[11-05-02.167][    0.000000] Memory: 1512672K/1966080K available (12608K kernel code, 1102K rwdata, 3664K rodata, 2112K init, 429K bss, 60192K reserved, 393216K cma-reserved)
[11-05-02.168][    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[11-05-02.168][    0.000000] rcu: Preemptible hierarchical RCU implementation.
[11-05-02.168][    0.000000] rcu:     RCU event tracing is enabled.
[11-05-02.168][    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[11-05-02.168][    0.000000]  Trampoline variant of Tasks RCU enabled.
[11-05-02.168][    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[11-05-02.168][    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[11-05-02.168][    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[11-05-02.168][    0.000000] GICv3: 480 SPIs implemented
[11-05-02.169][    0.000000] GICv3: 0 Extended SPIs implemented
[11-05-02.169][    0.000000] GICv3: Distributor has no Range Selector support
[11-05-02.170][    0.000000] GICv3: 16 PPIs implemented
[11-05-02.170][    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000011940000
[11-05-02.171][    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[11-05-02.171][    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[11-05-02.171][    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[11-05-02.171][    0.008228] Console: colour dummy device 80x25
[11-05-02.171][    0.012695] printk: console [tty0] enabled
[11-05-02.171][    0.016812] printk: bootconsole [scif0] disabled
[11-05-02.172][    0.021482] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[11-05-02.172][    0.021505] pid_max: default: 32768 minimum: 301
[11-05-02.172][    0.021646] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[11-05-02.504][    0.021667] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[11-05-02.504][    0.023331] rcu: Hierarchical SRCU implementation.
[11-05-02.505][    0.024015] Detected Renesas RZ/G2L r9a07g044 Rev 1
[11-05-02.505][    0.024283] EFI services will not be available.
[11-05-02.505][    0.024561] smp: Bringing up secondary CPUs ...
[11-05-02.505][    0.025077] Detected VIPT I-cache on CPU1
[11-05-02.505][    0.025119] GICv3: CPU1: found redistributor 100 region 0:0x0000000011960000
[11-05-02.505][    0.025171] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[11-05-02.505][    0.025298] smp: Brought up 1 node, 2 CPUs
[11-05-02.505][    0.025341] SMP: Total of 2 processors activated.
[11-05-02.506][    0.025352] CPU features: detected: Privileged Access Never
[11-05-02.506][    0.025361] CPU features: detected: LSE atomic instructions
[11-05-02.506][    0.025371] CPU features: detected: User Access Override
[11-05-02.506][    0.025382] CPU features: detected: 32-bit EL0 Support
[11-05-02.506][    0.025392] CPU features: detected: Common not Private translations
[11-05-02.506][    0.025403] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[11-05-02.506][    0.025420] CPU features: detected: CRC32 instructions
[11-05-02.506][    0.025430] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[11-05-02.506][    0.025442] CPU features: detected: 32-bit EL1 Support
[11-05-02.507][    0.043629] CPU: All CPU(s) started at EL1
[11-05-02.507][    0.043714] alternatives: patching kernel code
[11-05-02.507][    0.046176] devtmpfs: initialized
[11-05-02.507][    0.052375] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[11-05-02.508][    0.052432] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[11-05-02.508][    0.061800] pinctrl core: initialized pinctrl subsystem
[11-05-02.508][    0.062636] DMI not present or invalid.
[11-05-02.508][    0.063120] NET: Registered protocol family 16
[11-05-02.508][    0.064638] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[11-05-02.508][    0.064807] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[11-05-02.509][    0.064970] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[11-05-02.509][    0.065101] audit: initializing netlink subsys (disabled)
[11-05-02.509][    0.065443] audit: type=2000 audit(0.056:1): state=initialized audit_enabled=0 res=1
[11-05-02.509][    0.066007] thermal_sys: Registered thermal governor 'step_wise'
[11-05-02.509][    0.066376] cpuidle: using governor menu
[11-05-02.509][    0.066575] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[11-05-02.509][    0.066665] ASID allocator initialised with 65536 entries
[11-05-02.509][    0.094397] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[11-05-02.510][    0.094437] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[11-05-02.510][    0.094451] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[11-05-02.510][    0.094464] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[11-05-02.510][    0.096378] cryptd: max_cpu_qlen set to 1000
[11-05-02.510][    0.165991] raid6: neonx8   gen()  2132 MB/s
[11-05-02.510][    0.234049] raid6: neonx8   xor()  1641 MB/s
[11-05-02.510][    0.302126] raid6: neonx4   gen()  2192 MB/s
[11-05-02.511][    0.370190] raid6: neonx4   xor()  1630 MB/s
[11-05-02.512][    0.438259] raid6: neonx2   gen()  2092 MB/s
[11-05-02.513][    0.506325] raid6: neonx2   xor()  1493 MB/s
[11-05-02.513][    0.574402] raid6: neonx1   gen()  1807 MB/s
[11-05-02.513][    0.642460] raid6: neonx1   xor()  1255 MB/s
[11-05-02.513][    0.710527] raid6: int64x8  gen()  1510 MB/s
[11-05-02.513][    0.778572] raid6: int64x8  xor()   772 MB/s
[11-05-02.513][    0.846659] raid6: int64x4  gen()  1643 MB/s
[11-05-02.513][    0.914695] raid6: int64x4  xor()   837 MB/s
[11-05-02.513][    0.982750] raid6: int64x2  gen()  1484 MB/s
[11-05-02.514][    1.050816] raid6: int64x2  xor()   748 MB/s
[11-05-02.514][    1.118878] raid6: int64x1  gen()  1148 MB/s
[11-05-02.514][    1.186935] raid6: int64x1  xor()   559 MB/s
[11-05-02.514][    1.186947] raid6: using algorithm neonx4 gen() 2192 MB/s
[11-05-02.514][    1.186958] raid6: .... xor() 1630 MB/s, rmw enabled
[11-05-02.514][    1.186969] raid6: using neon recovery algorithm
[11-05-02.514][    1.190887] iommu: Default domain type: Translated 
[11-05-02.514][    1.191719] vgaarb: loaded
[11-05-02.514][    1.192129] SCSI subsystem initialized
[11-05-02.514][    1.192601] usbcore: registered new interface driver usbfs
[11-05-02.515][    1.192656] usbcore: registered new interface driver hub
[11-05-02.515][    1.192695] usbcore: registered new device driver usb
[11-05-02.850][    1.193530] mc: Linux media interface: v0.10
[11-05-02.850][    1.193566] videodev: Linux video capture interface: v2.00
[11-05-02.850][    1.193644] pps_core: LinuxPPS API ver. 1 registered
[11-05-02.851][    1.193656] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[11-05-02.851][    1.193681] PTP clock support registered
[11-05-02.851][    1.193718] EDAC MC: Ver: 3.0.0
[11-05-02.851][    1.195143] Advanced Linux Sound Architecture Driver Initialized.
[11-05-02.851][    1.196081] clocksource: Switched to clocksource arch_sys_counter
[11-05-02.851][    1.196326] VFS: Disk quotas dquot_6.6.0
[11-05-02.851][    1.196399] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[11-05-02.852][    1.202464] NET: Registered protocol family 2
[11-05-02.852][    1.202717] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[11-05-02.852][    1.203990] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[11-05-02.852][    1.204115] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[11-05-02.852][    1.204229] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
[11-05-02.852][    1.204512] TCP: Hash tables configured (established 16384 bind 16384)
[11-05-02.852][    1.204692] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[11-05-02.853][    1.204737] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[11-05-02.853][    1.204932] NET: Registered protocol family 1
[11-05-02.853][    1.205540] RPC: Registered named UNIX socket transport module.
[11-05-02.853][    1.205570] RPC: Registered udp transport module.
[11-05-02.854][    1.205581] RPC: Registered tcp transport module.
[11-05-02.854][    1.205591] RPC: Registered tcp NFSv4.1 backchannel transport module.
[11-05-02.855][    1.205610] PCI: CLS 0 bytes, default 64
[11-05-02.855][    1.206468] kvm [1]: HYP mode not available
[11-05-02.855][    1.208422] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[11-05-02.855][    1.214381] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[11-05-02.855][    1.215141] NFS: Registering the id_resolver key type
[11-05-02.855][    1.215201] Key type id_resolver registered
[11-05-02.855][    1.215213] Key type id_legacy registered
[11-05-02.855][    1.215306] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[11-05-02.855][    1.215332] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[11-05-02.856][    1.215368] jffs2: version 2.2. (NAND)2001-2006 Red Hat, Inc.
[11-05-02.856][    1.252414] xor: measuring software checksum speed
[11-05-02.856][    1.256797]    8regs           :  2281 MB/sec
[11-05-02.856][    1.260229]    32regs          :  2887 MB/sec
[11-05-02.856][    1.264263]    arm64_neon      :  2450 MB/sec
[11-05-02.856][    1.264275] xor: using function: 32regs (2887 MB/sec)
[11-05-02.856][    1.264352] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[11-05-02.857][    1.264542] io scheduler mq-deadline registered
[11-05-02.857][    1.264560] io scheduler kyber registered
[11-05-02.857][    1.266463] poeg-rzg2l 10048800.poega: RZ/G2L POEG Driver probed
[11-05-02.857][    1.266859] poeg-rzg2l 10048c00.poegb: RZ/G2L POEG Driver probed
[11-05-02.857][    1.267175] poeg-rzg2l 10049000.poegc: RZ/G2L POEG Driver probed
[11-05-02.857][    1.267337] poeg-rzg2l 10049400.poegd: RZ/G2L POEG Driver probed
[11-05-02.857][    1.310829] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[11-05-02.858][    1.311996] SuperH (H)SCI(F) driver initialized
[11-05-02.858][    1.323921] loop: module loaded
[11-05-02.858][    1.327252] tun: Universal TUN/TAP device driver, 1.6
[11-05-02.858][    1.327537] CAN device driver interface
[11-05-02.858][    1.328162] e1000e: Intel(R) PRO/1000 Network Driver
[11-05-02.859][    1.328182] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[11-05-02.859][    1.328841] VFIO - User Level meta-driver version: 0.3
[11-05-02.859][    1.329114] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[11-05-02.859][    1.329134] ehci-pci: EHCI PCI platform driver
[11-05-02.859][    1.329195] ehci-platform: EHCI generic platform driver
[11-05-02.859][    1.329919] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[11-05-02.859][    1.329973] ohci-pci: OHCI PCI platform driver
[11-05-02.860][    1.330057] ohci-platform: OHCI generic platform driver
[11-05-02.860][    1.331254] usbcore: registered new interface driver usb-storage
[11-05-02.860][    1.331788] renesas_usbhs 11c60000.usb: host probed
[11-05-02.860][    1.331811] renesas_usbhs 11c60000.usb: no transceiver found
[11-05-02.860][    1.331953] renesas_usbhs 11c60000.usb: gadget probed
[11-05-03.198][    1.332149] renesas_usbhs 11c60000.usb: platform init failed.
[11-05-03.198][    1.332300] renesas_usbhs 11c60000.usb: probe failed (-517)
[11-05-03.198][    1.333324] usbcore: registered new interface driver usbtouchscreen
[11-05-03.198][    1.333393] i2c /dev entries driver
[11-05-03.198][    1.338273] rzg2l-csi2 10830400.csi2: 2 lanes found
[11-05-03.198][    1.342373] device-mapper: ioctl: 4.43.0-ioctl (2020-10-01) initialised: dm-devel@redhat.com
[11-05-03.199][    1.342956] EDAC rzg2l-edac: IO mapped reg addr: 0x11410000
[11-05-03.199][    1.343255] EDAC MC0: Giving out device to module rzg2l-edac controller renesas,r9a07g044-edac: DEV 11410000.edac (INTERRUPT)
[11-05-03.199][    1.346094] ledtrig-cpu: registered to indicate activity on CPUs
[11-05-03.199][    1.346147] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[11-05-03.199][    1.346589] renesas_mtu3 10001200.timer: ch0: used as clock source
[11-05-03.199][    1.346616] clocksource: 10001200.timer: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 18664368 ns
[11-05-03.199][    1.346638] renesas_mtu3 10001200.timer: ch1: used for clock events
[11-05-03.199][    1.346660] renesas_mtu3 10001200.timer: Renesas MTU3 driver probed
[11-05-03.200][    1.347277] clocksource: timer@12801400: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns
[11-05-03.200][    1.347314] sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 21474836475ns
[11-05-03.200][    1.347335] /soc/timer@12801400: used for clocksource
[11-05-03.200][    1.347669] /soc/timer@12801800: used for clock events
[11-05-03.200][    1.348681] usbcore: registered new interface driver usbhid
[11-05-03.200][    1.348710] usbhid: USB HID core driver
[11-05-03.201][    1.349364] optee: probing for conduit method.
[11-05-03.201][    1.349392] optee: api uid mismatch
[11-05-03.201][    1.349415] optee: probe of firmware:optee failed with error -22
[11-05-03.202][    1.351800] IPVS: Registered protocols (TCP, UDP)
[11-05-03.203][    1.351881] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[11-05-03.203][    1.352113] IPVS: ipvs loaded.
[11-05-03.203][    1.352133] IPVS: [rr] scheduler registered.
[11-05-03.203][    1.352446] Initializing XFRM netlink socket
[11-05-03.203][    1.352869] NET: Registered protocol family 10
[11-05-03.203][    1.353885] Segment Routing with IPv6
[11-05-03.203][    1.354023] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[11-05-03.203][    1.354717] NET: Registered protocol family 17
[11-05-03.203][    1.354823] Bridge firewalling registered
[11-05-03.203][    1.354838] can: controller area network core
[11-05-03.203][    1.354901] NET: Registered protocol family 29
[11-05-03.204][    1.354918] can: raw protocol
[11-05-03.204][    1.354938] can: broadcast manager protocol
[11-05-03.204][    1.354957] can: netlink gateway - max_hops=1
[11-05-03.204][    1.355134] Key type dns_resolver registered
[11-05-03.204][    1.355658] registered taskstats version 1
[11-05-03.204][    1.356933] Btrfs loaded, crc32c=crc32c-generic
[11-05-03.204][    1.364812] thermal emergency: set temperature to 110 celsius
[11-05-03.204][    1.364977] thermal emergency: shutdown target cpus 1
[11-05-03.204][    1.364993] thermal emergency: freq scaled target cpus 0
[11-05-03.204][    1.367161] gpio-153 (gpio_sd0_pwr_en): hogged as output/high
[11-05-03.204][    1.367209] gpio-449 (sd0_dev_sel): hogged as output/high
[11-05-03.205][    1.367239] gpio-458 (can0_stb): hogged as output/low
[11-05-03.205][    1.367265] gpio-459 (can1_stb): hogged as output/low
[11-05-03.205][    1.367293] gpio-434 (sd1_pwr_en): hogged as output/high
[11-05-03.205][    1.367722] gpio gpiochip0: (11030000.pinctrl): detected irqchip that is shared with multiple gpiochips: please fix the driver.
[11-05-03.206][    1.368048] pinctrl-rzg2l 11030000.pinctrl: pinctrl-rzg2l support registered
[11-05-03.206][    1.371316] gpt-rzg2l 10048400.gpt: Can use GTETRGA as POEG, reset_counter
[11-05-03.206][    1.371358] gpt-rzg2l 10048400.gpt: Can use GTETRGB as POEG, reset_counter
[11-05-03.206][    1.371379] gpt-rzg2l 10048400.gpt: Can use GTETRGC as POEG, reset_counter
[11-05-03.206][    1.371398] gpt-rzg2l 10048400.gpt: Can use GTETRGD as POEG, reset_counter
[11-05-03.206][    1.372048] gpt-rzg2l 10048400.gpt: RZ/G2L GPT Driver probed
[11-05-03.206][    1.372748] 1004b800.serial: ttySC0 at MMIO 0x1004b800 (irq = 26, base_baud = 0) is a scif
[11-05-03.207][    2.728230] printk: console [ttySC0] enabled
[11-05-03.207][    2.735349] renesas_spi 1004b000.spi: DMA available
[11-05-03.207][    2.740708] renesas_spi 1004b000.spi: probed
[11-05-03.207][    2.746211] rcar_canfd 10050000.can: can_clk rate is 50000000
[11-05-03.268][    2.752643] rcar_canfd 10050000.can: device registered (channel 0)
[11-05-03.268][    2.758910] rcar_canfd 10050000.can: can_clk rate is 50000000
[11-05-03.269][    2.765140] rcar_canfd 10050000.can: device registered (channel 1)
[11-05-03.269][    2.771331] rcar_canfd 10050000.can: global operational state (clk 0, fdmode 1)
[11-05-03.269][    2.779549] ravb 11c20000.ethernet: no valid MAC address supplied, using a random one
[11-05-03.269][    2.790156] ravb 11c20000.ethernet eth0: Base address at 0x11c20000, 1e:d3:15:a9:48:d3, IRQ 131.
[11-05-03.270][    2.799973] ravb 11c30000.ethernet: no valid MAC address supplied, using a random one
[11-05-03.274][    2.810349] ravb 11c30000.ethernet eth1: Base address at 0x11c30000, 76:7b:a4:dc:60:e1, IRQ 134.
[11-05-03.317][    2.844124] ehci-platform 11c50100.usb: EHCI Host Controller
[11-05-03.317][    2.849848] ehci-platform 11c50100.usb: new USB bus registered, assigned bus number 1
[11-05-03.321][    2.857816] ehci-platform 11c50100.usb: irq 139, io mem 0x11c50100
[11-05-03.361][    2.876082] ehci-platform 11c50100.usb: USB 2.0 started, EHCI 1.10
[11-05-03.362][    2.882921] hub 1-0:1.0: USB hub found
[11-05-03.362][    2.886719] hub 1-0:1.0: 1 port detected
[11-05-03.362][    2.891655] ehci-platform 11c70100.usb: EHCI Host Controller
[11-05-03.365][    2.897368] ehci-platform 11c70100.usb: new USB bus registered, assigned bus number 2
[11-05-03.366][    2.905287] ehci-platform 11c70100.usb: irq 140, io mem 0x11c70100
[11-05-03.413][    2.924088] ehci-platform 11c70100.usb: USB 2.0 started, EHCI 1.10
[11-05-03.413][    2.930911] hub 2-0:1.0: USB hub found
[11-05-03.413][    2.934706] hub 2-0:1.0: 1 port detected
[11-05-03.413][    2.939553] ohci-platform 11c50000.usb: Generic Platform OHCI controller
[11-05-03.413][    2.946319] ohci-platform 11c50000.usb: new USB bus registered, assigned bus number 3
[11-05-03.417][    2.954282] ohci-platform 11c50000.usb: irq 137, io mem 0x11c50000
[11-05-03.531][    3.050732] hub 3-0:1.0: USB hub found
[11-05-03.531][    3.054535] hub 3-0:1.0: 1 port detected
[11-05-03.531][    3.059384] ohci-platform 11c70000.usb: Generic Platform OHCI controller
[11-05-03.532][    3.066151] ohci-platform 11c70000.usb: new USB bus registered, assigned bus number 4
[11-05-03.535][    3.074108] ohci-platform 11c70000.usb: irq 138, io mem 0x11c70000
[11-05-03.648][    3.170722] hub 4-0:1.0: USB hub found
[11-05-03.649][    3.174525] hub 4-0:1.0: 1 port detected
[11-05-03.649][    3.179394] renesas_usbhs 11c60000.usb: host probed
[11-05-03.649][    3.184330] renesas_usbhs 11c60000.usb: no transceiver found
[11-05-03.649][    3.190104] renesas_usbhs 11c60000.usb: gadget probed
[11-05-03.653][    3.195401] renesas_usbhs 11c60000.usb: probed
[11-05-03.882][    3.244217] ov5645 0-003c: ov5645_write_reg: write reg error -6: reg=3103, val=11
[11-05-03.883][    3.251718] ov5645 0-003c: could not set init registers
[11-05-03.883][    3.256945] ov5645 0-003c: could not power up OV5645
[11-05-03.883][    3.262297] i2c-riic 10058000.i2c: registered with 100000Hz bus speed
[11-05-03.883][    3.277848] i2c-riic 10058400.i2c: registered with 100000Hz bus speed
[11-05-03.883][    3.286202] raa215300 3-0012: RTC enabled
[11-05-03.884][    3.290286] raa215300 3-0012: RAA215300 initialized
[11-05-03.884][    3.295786] rtc-isl1208 3-006f: rtc power failure detected, please set clock.
[11-05-03.884][    3.303208] rtc-isl1208 3-006f: Using external oscillator
[11-05-03.884][    3.310337] rtc-isl1208 3-006f: registered as rtc0
[11-05-03.884][    3.315496] rtc-isl1208 3-006f: setting system clock to 2000-01-01T00:00:00 UTC (946684800)
[11-05-03.884][    3.329407] i2c-riic 10058c00.i2c: registered with 400000Hz bus speed
[11-05-03.884][    3.339748] spi-nor spi1.0: mt25qu512a (65536 Kbytes)
[11-05-03.884][    3.345566] 5 fixed-partitions partitions found on MTD device spi1.0
[11-05-03.884][    3.351939] Creating 5 MTD partitions on "spi1.0":
[11-05-03.884][    3.356724] 0x000000000000-0x000000080000 : "u-boot"
[11-05-03.885][    3.362879] 0x000000080000-0x0000000c0000 : "env"
[11-05-03.885][    3.368852] 0x0000000c0000-0x000000100000 : "dtb"
[11-05-03.885][    3.374800] 0x000000800000-0x000001800000 : "rootfs"
[11-05-03.885][    3.381019] 0x000002000000-0x000002100000 : "test-area"
[11-05-03.885][    3.384308] renesas_sdhi_internal_dmac 11c00000.mmc: mmc0 base at 0x0000000011c00000, max clock rate 100 MHz
[11-05-03.885][    3.392424] rz-ssi-pcm-audio 10049c00.ssi: DMA enabled
[11-05-03.885][    3.396315] renesas_sdhi_internal_dmac 11c10000.mmc: mmc1 base at 0x0000000011c10000, max clock rate 100 MHz
[11-05-03.886][    3.402319] rz-ssi-pcm-audio 1004a000.ssi: DMA enabled
[11-05-03.887][    3.418738] [drm] Initialized rcar-du 1.0.0 20130110 for 10890000.display on minor 0
[11-05-03.888][    3.426540] [drm] Device 10890000.display probed
[11-05-04.020][    3.519665] Console: switching to colour frame buffer device 240x67
[11-05-04.020][    3.558023] rcar-du 10890000.display: [drm] fb0: rcar-dudrmfb frame buffer device
[11-05-04.088][    3.600666] mmc0: new HS200 MMC card at address 0001
[11-05-04.088][    3.606604] mmcblk0: mmc0:0001 G1J38E 59.3 GiB 
[11-05-04.088][    3.611439] mmcblk0boot0: mmc0:0001 G1J38E partition 1 31.5 MiB
[11-05-04.088][    3.617668] mmcblk0boot1: mmc0:0001 G1J38E partition 2 31.5 MiB
[11-05-04.089][    3.623941] mmcblk0rpmb: mmc0:0001 G1J38E partition 3 4.00 MiB, chardev (242:0)
[11-05-04.090][    3.632706]  mmcblk0: p1
[11-05-04.121][    3.673171] ALSA device list:
[11-05-04.148][    3.676282]   #0: rz-ssi-dai-wm8978-hifi
[11-05-04.149][    3.680299]   #1: sound_card
[11-05-04.149][    3.684245] Waiting for root device /dev/mmcblk1p2...
[11-05-04.277][    3.810046] mmc1: new ultra high speed SDR104 SDHC card at address 59b4
[11-05-04.277][    3.817613] mmcblk1: mmc1:59b4 SN32G 29.7 GiB 
[11-05-04.280][    3.823956]  mmcblk1: p1 p2
[11-05-04.422][    3.932194] EXT4-fs (mmcblk1p2): recovery complete
[11-05-04.422][    3.940179] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
[11-05-04.422][    3.948484] VFS: Mounted root (ext4 filesystem) on device 179:26.
[11-05-04.422][    3.955681] devtmpfs: mounted
[11-05-04.426][    3.961039] Freeing unused kernel memory: 2112K
[11-05-04.426][    3.965776] Run /sbin/init as init process
[11-05-04.701][    4.237604] systemd[1]: System time before build time, advancing clock.
[11-05-04.764][    4.286108] systemd[1]: systemd 244 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
[11-05-04.768][    4.308379] systemd[1]: Detected architecture arm64.
[11-05-04.796]
[11-05-04.797]Welcome to Poky (Yocto Project Reference Distro) 3.1.26 (dunfell)!
[11-05-04.797]
[11-05-04.813][    4.349122] systemd[1]: Set hostname to <smarc-rzg2l>.
[11-05-05.181][    4.711029] systemd[1]: /lib/systemd/system/docker.socket:6: ListenStream= references a path below legacy directory /var/run/, updating /var/run/docker.sock 鈫/run/docker.sock; please update the unit file accordingly.
[11-05-05.387][    4.827334] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-05.387][    4.834524] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
[11-05-05.387][    4.847148] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
[11-05-05.388][    4.859914] systemd[1]: Created slice system-getty.slice.
[11-05-05.388][  OK  ] Created slice system-getty.slice.
[11-05-05.388][    4.880486] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-05.388][    4.889440] systemd[1]: Created slice system-serial\x2dgetty.slice.
[11-05-05.388][  OK  ] Created slice system-serial\x2dgetty.slice.
[11-05-05.388][    4.912334] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-05.388][    4.921080] systemd[1]: Created slice User and Session Slice.
[11-05-05.389][  OK  ] Created slice User and Session Slice.
[11-05-05.414][    4.944760] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[11-05-05.418][  OK  ] Started Dispatch Password 鈥s to Console Directory Watch.
[11-05-05.471][    4.972697] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[11-05-05.472][  OK  ] Started Forward Password R鈥ests to Wall Directory Watch.
[11-05-05.472][    4.996638] systemd[1]: Reached target Host and Network Name Lookups.
[11-05-05.475][  OK  ] Reached target Host and Network Name Lookups.
[11-05-05.476][    5.024464] systemd[1]: Reached target Paths.
[11-05-05.492][  OK  ] Reached target Paths.
[11-05-05.523][    5.048447] systemd[1]: Reached target Remote File Systems.
[11-05-05.524][  OK  ] Reached target Remote File Systems.
[11-05-05.540][    5.076465] systemd[1]: Reached target Slices.
[11-05-05.541][  OK  ] Reached target Slices.
[11-05-05.572][    5.100477] systemd[1]: Reached target Swap.
[11-05-05.573][  OK  ] Reached target Swap.
[11-05-05.633][    5.136169] systemd[1]: Listening on RPCbind Server Activation Socket.
[11-05-05.633][  OK  ] Listening on RPCbind Server Activation Socket.
[11-05-05.633][    5.164484] systemd[1]: Reached target RPC Port Mapper.
[11-05-05.637][  OK  ] Reached target RPC Port Mapper.
[11-05-05.666][    5.194067] systemd[1]: Listening on Syslog Socket.
[11-05-05.666][  OK  ] Listening on Syslog Socket.
[11-05-05.718][    5.220921] systemd[1]: Listening on initctl Compatibility Named Pipe.
[11-05-05.718][  OK  ] Listening on initctl Compatibility Named Pipe.
[11-05-05.718][    5.249314] systemd[1]: Listening on Journal Audit Socket.
[11-05-05.723][  OK  ] Listening on Journal Audit Socket.
[11-05-05.774][    5.277044] systemd[1]: Listening on Journal Socket (/dev/log).
[11-05-05.774][  OK  ] Listening on Journal Socket (/dev/log).
[11-05-05.777][    5.305163] systemd[1]: Listening on Journal Socket.
[11-05-05.777][  OK  ] Listening on Journal Socket.
[11-05-05.830][    5.333269] systemd[1]: Listening on Network Service Netlink Socket.
[11-05-05.831][  OK  ] Listening on Network Service Netlink Socket.
[11-05-05.831][    5.361224] systemd[1]: Listening on udev Control Socket.
[11-05-05.834][  OK  ] Listening on udev Control Socket.
[11-05-05.867][    5.388914] systemd[1]: Listening on udev Kernel Socket.
[11-05-05.867][  OK  ] Listening on udev Kernel Socket.
[11-05-05.887][    5.422311] systemd[1]: Mounting Huge Pages File System...
[11-05-05.887]         Mounting Huge Pages File System...
[11-05-05.930][    5.454100] systemd[1]: Mounting POSIX Message Queue File System...
[11-05-05.931]         Mounting POSIX Message Queue File System...
[11-05-05.963][    5.486015] systemd[1]: Mounting Kernel Debug File System...
[11-05-05.964]         Mounting Kernel Debug File System...
[11-05-05.990][    5.518656] systemd[1]: Mounting Temporary Directory (/tmp)...
[11-05-05.994]         Mounting Temporary Directory (/tmp)...
[11-05-06.029][    5.555598] systemd[1]: Starting Create list of static device nodes for the current kernel...
[11-05-06.036]         Starting Create list of st鈥des for the current kernel...
[11-05-06.139][    5.605023] systemd[1]: Starting Start psplash boot splash screen...
[11-05-06.139]         Starting Start psplash boot splash screen...
[11-05-06.170][    5.638838] systemd[1]: Starting RPC Bind...
[11-05-06.171]         Starting RPC Bind...
[11-05-06.171][    5.688539] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[11-05-06.171][    5.707133] systemd[1]: Starting Journal Service...
[11-05-06.180]         Starting Journal Service...
[11-05-06.220][    5.740999] systemd[1]: Starting Load Kernel Modules...
[11-05-06.220]         Starting Load Kernel Modules...
[11-05-06.247][    5.773784] systemd[1]: Starting Remount Root and Kernel File Systems...
[11-05-06.253]         Starting Remount Root and Kernel File Systems...
[11-05-06.282][    5.806306] systemd[1]: Starting udev Coldplug all Devices...
[11-05-06.288][    5.813849] mali_kbase: loading out-of-tree module taints kernel.
[11-05-06.288]         Starting udev Coldplug all Devices...
[11-05-06.378][    5.839962] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-06.378][    5.856749] systemd[1]: Started Start psplash boot splash screen.
[11-05-06.380][  OK      5.868257] mali 11840000.gpu: Kernel DDK version r45p0-01eac0
[11-05-06.380]0m] Started Start psplash boot splash s[    5.878332] mali 11840000.gpu: Register LUT 00070000 initialized for GPU arch 0x00070009
[11-05-06.381]creen.
[11-05-06.381][    5.894011] mali 11840000.gpu: GPU identified as 0x3 arch 7.0.9 r0p0 status 0
[11-05-06.381][    5.907466] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
[11-05-06.381][    5.908426] mali 11840000.gpu: No priority control manager is configured
[11-05-06.383][    5.920429] mali 11840000.gpu: No memory group manager is configured
[11-05-06.449][    5.939946] systemd[1]: Started RPC Bind.
[11-05-06.449][    5.940641] random: systemd-journal: uninitialized urandom read (16 bytes read)
[11-05-06.450][    5.949341] mali 11840000.gpu: Probed as mali0
[11-05-06.450][    5.951639] random: systemd-journal: uninitialized urandom read (16 bytes read)
[11-05-06.450][  OK      5.964255] rgnmm_drv mmngr: assigned reserved memory node linux,multimedia
[11-05-06.454]0m] Started RPC Bind.
[11-05-06.454][    5.985164] systemd[1]: Started Journal Service.
[11-05-06.454][  OK  ] Started Journal Service.
[11-05-06.544][  OK  ] Mounted Huge Pages File System.
[11-05-06.544][  OK  ] Mounted POSIX Message Queue File System.
[11-05-06.549][  OK  ] Mounted Kernel Debug File System.
[11-05-06.566][  OK  ] Mounted Temporary Directory (/tmp).
[11-05-06.588][  OK  ] Started Create list of sta鈥nodes for the current kernel.
[11-05-06.604][  OK  ] Started Load Kernel Modules.
[11-05-06.626][  OK  ] Started Remount Root and Kernel File Systems.
[11-05-06.653]         Mounting Kernel Configuration File System...
[11-05-06.671][  OK  ] Started Start psplash-syst鈥rogress communication helper.
[11-05-06.698]         Starting Flush Journal to Persistent Storage...
[11-05-06.742]         Starting Apply Kernel Variables...
[11-05-06.745][    6.266680] systemd-journald[166]: Received client request to flush runtime journal.
[11-05-06.746]         Starting Create Static Device Nodes in /dev...
[11-05-06.775][  OK  ] Mounted Kernel Configuration File System.
[11-05-06.796][  OK  ] Started Flush Journal to Persistent Storage.
[11-05-06.843][  OK  ] Started Apply Kernel Variables.
[11-05-06.876][  OK  ] Started Create Static Device Nodes in /dev.
[11-05-06.881][  OK  ] Reached target Local File Systems (Pre).
[11-05-06.901]         Mounting /var/volatile...
[11-05-06.925]         Starting udev Kernel Device Manager...
[11-05-06.941][  OK  ] Mounted /var/volatile.
[11-05-06.973]         Starting Load/Save Random Seed...
[11-05-07.137][  OK  ] Started udev Kernel Device Manager.
[11-05-07.283][  OK  ] Started udev Coldplug all Devices.
[11-05-07.673][    7.208017] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-07.857][    7.385107] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-07.857][    7.394593] random: systemd: uninitialized urandom read (16 bytes read)
[11-05-08.187][  OK  ] Created slice system-weston.slice.
[11-05-08.277][    7.812182] random: crng init done
[11-05-08.277][    7.815600] random: 85 urandom warning(s) missed due to ratelimiting
[11-05-08.315][  OK  ] Started Load/Save Random Seed.
[11-05-08.369][  OK  ] Reached target Hardware activated USB gadget.
[11-05-08.657][  OK  ] Found device /dev/mmcblk1p1.
[11-05-08.689]         Mounting /boot...
[11-05-08.735][    8.270354] FAT-fs (mmcblk1p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[11-05-08.751][  OK  ] Mounted /boot.
[11-05-08.768][  OK  ] Reached target Local File Systems.
[11-05-08.794]         Starting Create Volatile Files and Directories...
[11-05-08.854][  OK  ] Started Create Volatile Files and Directories.
[11-05-08.885]         Starting Network Time Synchronization...
[11-05-08.909]         Starting Update UTMP about System Boot/Shutdown...
[11-05-08.957][  OK  ] Started Update UTMP about System Boot/Shutdown.
[11-05-09.150][  OK  ] Started Network Time Synchronization.
[11-05-09.226][  OK  ] Reached target System Initialization.
[11-05-09.226][  OK  ] Started Daily Cleanup of Temporary Directories.
[11-05-09.227][  OK  ] Reached target System Time Set.
[11-05-09.230][  OK  ] Reached target System Time Synchronized.
[11-05-09.231][  OK  ] Reached target Timers.
[11-05-09.252][  OK  ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[11-05-09.273][  OK  ] Listening on D-Bus System Message Bus Socket.
[11-05-09.306]         Starting Docker Socket for the API.
[11-05-09.306][  OK  ] Listening on dropbear.socket.
[11-05-09.327][  OK  ] Listening on Docker Socket for the API.
[11-05-09.343][  OK  ] Reached target Sockets.
[11-05-09.359][  OK  ] Reached target Basic System.
[11-05-09.387]         Starting Save/Restore Sound Card State...
[11-05-09.408][  OK  ] Started Kernel Logging Service.
[11-05-09.447][  OK  ] Started System Logging Service.
[11-05-09.472][  OK  ] Started D-Bus System Message Bus.
[11-05-09.516]         Starting IPv6 Packet Filtering Framework...
[11-05-09.539]         Starting IPv4 Packet Filtering Framework...
[11-05-09.564]         Starting Network Time Service (one-shot ntpdate mode)...
[11-05-09.580]         Starting Telephony service...
[11-05-09.596][  OK  ] Started optee services.
[11-05-09.677]         Starting Login Service...
[11-05-09.724][  OK  ] Started VIN initializing setting.
[11-05-09.724][  OK  ] Started WatchdogTimer.
[11-05-09.753][  OK  ] Started Save/Restore Sound Card State.
[11-05-09.775][  OK  ] Started IPv6 Packet Filtering Framework.
[11-05-09.795][  OK  ] Started IPv4 Packet Filtering Framework.
[11-05-09.816][  OK  ] Started Network Time Service (one-shot ntpdate mode).
[11-05-09.928][  OK  ] Started Telephony service.
[11-05-10.840][  OK  ] Started Login Service.
[11-05-10.872][  OK  ] Reached target Network (Pre).
[11-05-10.888][  OK  ] Reached target Sound Card.
[11-05-10.904]         Starting Connection service...
[11-05-10.919]         Starting Network Service...
[11-05-11.178][  OK  ] Started Network Service.
[11-05-11.206]         Starting Wait for Network to be Configured...
[11-05-11.241][   10.770732] Microchip KSZ9131 Gigabit PHY 11c30000.ethernet-ffffffff:07: attached PHY driver [Microchip KSZ9131 Gigabit PHY] (mii_bus:phy_addr=11c30000.ethernet-ffffffff:07, irq=173)
[11-05-11.284][  OK  ] Started Connection service.
[11-05-11.326][  OK  ] Reac[   10.836042] Microchip KSZ9131 Gigabit PHY 11c20000.ethernet-ffffffff:07: attached PHY driver [Microchip KSZ9131 Gigabit PHY] (mii_bus:phy_addr=11c20000.ethernet-ffffffff:07, irq=172)
[11-05-11.327]hed target Network.
[11-05-11.327][  OK  ] Reached target Network is Online.
[11-05-11.368]         Starting Avahi mDNS/DNS-SD Stack...
[11-05-11.372][   10.902069] audit: type=1325 audit(1600598644.660:2): table=filter family=2 entries=4 op=xt_replace pid=237 comm="connmand"
[11-05-11.389]         Starting Wait for network to be configured by ConnMan...
[11-05-11.417]         Starting LSB: start and stop docker...
[11-05-11.439]         Starting Docker Application Container Engine...
[11-05-11.455]         Starting Network Time Service...
[11-05-11.471]         Starting Permit User Sessions...
[11-05-11.509]         Starting Target Communication Framework agent...
[11-05-11.559][   11.088747] audit: type=1325 audit(1600598644.848:3): table=nat family=2 entries=5 op=xt_replace pid=237 comm="connmand"
[11-05-11.601][  OK  ] Started Permit User Sessions.
[11-05-11.629][  OK  ] Started LSB: start and stop docker.
[11-05-11.650][  OK  ] Started Avahi mDNS/DNS-SD Stack.
[11-05-11.713][  OK  ] Started Getty on tty1.
[11-05-11.745][  OK  ] Started Serial Getty on ttySC0.
[11-05-11.763][  OK  ] Reached target Login Prompts.
[11-05-11.779]         Starting Hostname Service...
[11-05-11.809]         Starting WPA supplicant...
[11-05-11.836][  OK  ] Started Target Communication Framework agent.
[11-05-11.978][  OK  ] Started Network Time Service.
[11-05-12.058][  OK  ] Started Hostname Service.
[11-05-12.091][  OK  ] Started WPA supplicant.
[11-05-14.731][   14.187290] audit: type=1325 audit(1600598647.944:4): table=nat family=2 entries=5 op=xt_replace pid=311 comm="iptables"
[11-05-14.732][   14.203025] audit: type=1325 audit(1600598647.960:5): table=filter family=2 entries=4 op=xt_replace pid=313 comm="iptables"
[11-05-14.732][   14.215506] audit: type=1325 audit(1600598647.972:6): table=filter family=2 entries=6 op=xt_replace pid=315 comm="iptables"
[11-05-14.733][   14.229425] audit: type=1325 audit(1600598647.984:7): table=filter family=2 entries=8 op=xt_replace pid=317 comm="iptables"
[11-05-14.733][   14.242907] audit: type=1325 audit(1600598648.000:8): table=filter family=2 entries=10 op=xt_replace pid=319 comm="iptables"
[11-05-14.734][   14.257552] audit: type=1325 audit(1600598648.016:9): table=filter family=2 entries=11 op=xt_replace pid=321 comm="iptables"
[11-05-14.735][   14.268974] audit: type=1325 audit(1600598648.020:10): table=filter family=2 entries=12 op=xt_replace pid=322 comm="iptables"
[11-05-14.822][   14.351520] audit: type=1325 audit(1600598648.108:11): table=nat family=2 entries=7 op=xt_replace pid=328 comm="iptables"
[11-05-15.788][   15.322702] process 'docker/tmp/qemu-check235759621/check' started with executable stack
[11-05-15.849][  OK  ] Started Docker Application Container Engine.
[11-05-15.867][  OK  ] Reached target Multi-User System.
[11-05-15.899]         Starting Update UTMP about System Runlevel Changes...
[11-05-15.923][  OK  ] Started Weston Wayland Compositor.
[11-05-15.970][  OK  ] Started Update UTMP about System Runlevel Changes.
[11-05-16.011][  OK  ] Created slice User Slice of UID 0.
[11-05-16.035]         Starting User Runtime Directory /run/user/0...
[11-05-16.075][  OK  ] Started User Runtime Directory /run/user/0.
[11-05-16.092]         Starting User Manager for UID 0...
[11-05-17.757]
[11-05-17.757]Poky (Yocto Project Reference Distro) 3.1.26 smarc-rzg2l ttySC0
[11-05-17.757]
[11-05-17.757]BSP: RZG2L/RZG2L-SMARC-EVK/3.0.5
[11-05-17.757]LSI: RZG2L
[11-05-17.760]Version: 3.0.5
[11-06-53.958]smarc-rzg2l login: root
[11-06-53.990]Last login: Sun Sep 20 10:44:09 UTC 2020
[11-06-54.178]numid=59,iface=MIXER,name='Left Input Mixer L2 Switch'
[11-06-54.178]  ; type=BOOLEAN,access=rw------,values=1
[11-06-54.178]  : values=on
[11-06-54.178]numid=62,iface=MIXER,name='Right Input Mixer R2 Switch'
[11-06-54.178]  ; type=BOOLEAN,access=rw------,values=1
[11-06-54.178]  : values=on
[11-06-54.178]numid=41,iface=MIXER,name='Headphone Playback Volume'
[11-06-54.179]  ; type=INTEGER,access=rw---R--,values=2,min=0,max=63,step=0
[11-06-54.179]  : values=63,63
[11-06-54.179]  | dBscale-min=-57.00dB,step=1.00dB,mute=0
[11-06-54.180]numid=5,iface=MIXER,name='PCM Volume'
[11-06-54.180]  ; type=INTEGER,access=rw---R--,values=2,min=0,max=255,step=0
[11-06-54.180]  : values=255,255
[11-06-54.180]  | dBscale-min=-127.50dB,step=0.50dB,mute=1
[11-06-54.181]numid=48,iface=MIXER,name='Input PGA Volume'
[11-06-54.182]  ; type=INTEGER,access=rw---R--,values=2,min=0,max=63,step=0
[11-06-54.182]  : values=25,25
[11-06-54.182]  | dBscale-min=-12.00dB,step=0.75dB,mute=0
[11-06-54.839]root@smarc-rzg2l:~# 

五 参考
https://www.renesas.com/us/en/products/microcontrollers-microprocessors/rz-mpus/rzg2l-getting-started

本文来自互联网用户投稿,该文观点仅代表作者本人,不代表本站立场。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如若转载,请注明出处:http://www.rhkb.cn/news/194916.html

如若内容造成侵权/违法违规/事实不符,请联系长河编程网进行投诉反馈email:809451989@qq.com,一经查实,立即删除!

相关文章

JavaEE进阶学习:Spring核心和设计思想

Spring 是什么 我们通常所说的 Spring 指的是 Spring Framework&#xff08;Spring 框架&#xff09;&#xff0c;它是⼀个开源框架&#xff0c;有着活跃而庞大的社区&#xff0c;这就是它之所以能长久不衰的原因。Spring 支持广泛的应用场景&#xff0c;它可以让 Java 企业级…

Cesium深入浅出之自定义材质

引子 做为一名技术宅却没有能拿得出手的技术无疑是最可悲的事情。三年前&#xff0c;当我第一次接触Cesium的时候就被它强大和炫丽所折服&#xff0c;最关键的是它还是开源的。以前我一直是机械地敲着业务代码&#xff0c;好像计算机程序就只能干这点事情一样&#xff0c;而 C…

CSS---关于font文本属性设置样式总结

目录 1、color属性 2、font-size属性 3、font-weight属性 4、font-family属性 5、text-align属性 6、line-height属性 7、text-indent属性 8、letter-spacing属性 9、word-spacing属性 10、word-break属性 11、white-space属性 12、text-transform 12、writing-mo…

【开源】基于Vue.js的社区买菜系统的设计和实现

项目编号&#xff1a; S 011 &#xff0c;文末获取源码。 \color{red}{项目编号&#xff1a;S011&#xff0c;文末获取源码。} 项目编号&#xff1a;S011&#xff0c;文末获取源码。 目录 一、摘要1.1 项目介绍1.2 项目录屏 二、系统设计2.1 功能模块设计2.1.1 数据中心模块2.1…

IgH Master环境搭建

目标&#xff1a;实时linux内核中运行IgH主站&#xff0c;ethercat的用户态工具能看到主站信息。 一、需要的软件 1&#xff0c;vbox虚拟机 https://www.virtualbox.org/&#xff0c;下载VirtualBox 7.0, 备注&#xff1a;windows中不要用wsl开发&#xff0c;wsl运行unbuntu…

Accelerate 0.24.0文档 三:超大模型推理(内存估算、Sharded checkpoints、bitsandbytes量化、分布式推理)

文章目录 一、内存估算1.1 Gradio Demos1.2 The Command 二、使用Accelerate加载超大模型2.1 模型加载的常规流程2.2 加载空模型2.3 分片检查点&#xff08;Sharded checkpoints&#xff09;2.4 示例&#xff1a;使用Accelerate推理GPT2-1.5B2.5 device_map 三、bitsandbytes量…

内网Jenkins 部署.net(dotnet)项目

一、前置条件 内网部署Jenkins&#xff0c;并安装好所需插件 此篇内容需承接内网搭建Jenkins自动化远程部署项目到Windows服务器_jenkins内网安装-CSDN博客 &#xff0c;才更好操作与理解 二、在Jenkins中创建项目 三、配置项目 General Source Code Management Build Envi…

iddata函数合成的数据中采样间隔时间的两种设置方式及其程序举例

iddata函数生成的数据中采样间隔时间的两种设置方式及其程序举例 在对iddata合成的结构体数据&#xff0c;对采样间隔时间的设置可以通过两种方式实现&#xff0c;本文简要讲解其设置方式。 在设置采样间隔时候&#xff0c;会用到属性“ts”。 (1)对于单次实验&#xff0c;ts…

Python语言 range()函数用方法

range() 是Python的一个内置函数&#xff0c;返回的是一个可迭代对象。用于创建数字序列。 语法格式&#xff1a; range(start, stop, step) 即&#xff1a; range(初值, 终值, 步长) range()函数中使用一个参数&#xff1a; 比如&#xff1a;range(6) 返回从0到6&#x…

Java实现俄罗斯方块游戏

俄罗斯方块游戏本身的逻辑&#xff1a; 俄罗斯方块游戏的逻辑是比较简单的。它就类似于堆砌房子一样&#xff0c;各种各样的方地形状是不同的。但是&#xff0c;俄罗斯方块游戏的界面被等均的分为若干行和若干列&#xff0c;因此方块的本质就是占用了多少个单元。 首先来考虑…

文本格式清理工具 TextSoap mac中文版软件特色

TextSoap mac是一款文本格式清理工具。TextSoap可以帮助用户清除掉text文档内的文字格式&#xff0c;还可以将文档内的url转换成超链接&#xff0c;简单方便&#xff0c;是你日常办公不可缺少的工具。 TextSoap for mac软件特色 1、清洁界面 2、集成文本编辑器 3、100多个内…

FPGA模块——IIC协议(FPGA做主机操作24C64)

FPGA模块——IIC协议&#xff08;FPGA做主机操作24C64&#xff09; EEPROM&#xff08;24C64&#xff09;向器件写数据时序向器件读数据时序 IIC协议FPGA主机代码IIC读寄存器驱动&#xff08;指定地址单次读写&#xff09;使用 IIC模块 EEPROM&#xff08;24C64&#xff09; 掉…

Linux基础命令(2)

现在class03下面有这些 用ls -R看到test里面也是有东西的&#xff0c;也就是test目录文件非空 那么现在在03下面mkdir建一个空的目录文件tes&#xff0c;刚建好里面还什么都没有放 那么想要删除操作的话——要用什么命令 1.rmdir&#xff1a;用来删除空的目录文件的命令 删除刚…

K8s 命令行

前言&#xff1a;关于k8s 与 docker Docker和Kubernetes&#xff08;通常简称为K8s&#xff09;是两个在容器化应用程序方面非常流行的开源工具。 Docker: Docker 是一种轻量级的容器化平台&#xff0c;允许开发者将应用程序及其所有依赖项打包到一个称为容器的可移植容器中…

VIM去掉utf-8 bom头

Windows系统的txt文件在使用utf-8编码保存时会默认在文件开头插入三个不可见的字符&#xff08;0xEF 0xBB 0xBF&#xff09;称为BOM头 BOM头文件 0.加上BOM标记&#xff1a; :set bomb 1.查询当前UTF-8编码的文件是否有BOM标记&#xff1a; :set bomb? :set bomb? 2.BOM头:文…

CentOs 7 PHP安装和配置

目录 1 安装epel源 2 安装REMI源 3 安装yum源管理工具 4 安装PHP7.3 5 启动php服务 6 设置PHP 6.1 查找安装包 6.2 查找PHP安装位置 6.3 查找php配置文件位置 6.4 配置PHP 6.5 设置快捷命令 6.6 查看php版本 6.7 更新php 1 安装epel源 yum -y install epel-release 2 安…

深度学习之基于YoloV5苹果新鲜程度检测识别系统

欢迎大家点赞、收藏、关注、评论啦 &#xff0c;由于篇幅有限&#xff0c;只展示了部分核心代码。 文章目录 一项目简介 深度学习之基于 YOLOv5 苹果新鲜程度检测识别系统介绍YOLOv5 简介苹果新鲜程度检测系统系统架构应用场景 二、功能三、系统四. 总结 一项目简介 深度学习之…

OSPF开放最短路径优先(Open Shortest Path First)协议

OSPF开放最短路径优先(Open Shortest Path First)协议 为克服RIP的缺点(限制网络规模&#xff0c;坏消息传得慢)在1989年开发出来的原理很简单&#xff0c;但实现很复杂使用了Dijkstra提出的最短路径算法SPF(Shortest Path First)采用分布式的链路状态协议(link state protoco…

Windows Server 2012 R2系统服务器远程桌面服务多用户登录配置分享

Windows Server 2012系统在没有安装远程多界面的情况下&#xff0c;最多只能同时运行2个远程桌面&#xff0c;如果是有多个技术员、合伙人同时操作或是像游戏开发需要用到多界面&#xff0c;但是没有安装就很不方便&#xff0c;今天飞飞来和你们分享Windows server 2012R2系统远…

泛型编程 -- 模板详解

一、模板 在没有模板之前&#xff0c;如果我们写一个swap()两数交换函数&#xff0c;因为我们要支持 int 与int 交换 、double 与 double 交换等等情况&#xff0c;所以要实现swap()函数的多个重载&#xff0c;显得很繁琐&#xff0c;于是就引入了模板。 模板就是在需要模板的地…