STM32存储左右互搏 SPI总线FATS读写FRAM MB85RS2M

STM32存储左右互搏 SPI总线FATS读写FRAM MB85RS2M

在中低容量存储领域，除了FLASH的使用，，还有铁电存储器FRAM的使用，相对于FLASH，FRAM写操作时不需要预擦除，所以执行写操作时可以达到更高的速度，其主要优点为没有FLASH持续写操作跨页地址需要变换的要求。相比于SRAM则具有非易失性, 因此价格方面会高一些。MB85RS2M是256K Byte（2M bit）的FRAM，能够按字节进行写入且没有写入等待时间。其管脚功能兼容FLASH：在这里插入图片描述
这里介绍STM32 FATS文件操作方式访问FRAM MB85RS2M的例程。采用STM32CUBEIDE开发平台，以STM32F401CCU6芯片为例，通过STM32 SPI硬件电路实现读写操作，通过USB虚拟串口进行控制。

STM32工程配置

首先建立基本工程并设置时钟：
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
配置硬件SPI接口:
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
增加配置PA4作为SPI软件代码控制输出的片选管脚
并增加PA2和PA3连接到/WP和/HOLD管脚，并保持输出高电平:
在这里插入图片描述
配置USB作为通讯口：
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
对FATS文件系统进行配置:
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
保存并生成初始工程代码：
在这里插入图片描述

STM32工程代码

USB虚拟串口的使用参考：STM32 USB VCOM和HID的区别，配置及Echo功能实现（HAL）
代码里用到的微秒延时函数参考： STM32 HAL us delay（微秒延时）的指令延时实现方式及优化

建立MB85RS2M.h头文件：

#ifndef INC_MB85RS2M_H_
#define INC_MB85RS2M_H_
#include "main.h"/*To define operation code*/
#define WREN 0x06    //Set Write Enable Latch
#define WRDI 0x04    //Reset Write Enable Latch
#define RDSR 0x05    //Read Status Register
#define WRSR 0x01    //Write Status Register
#define READ 0x03    //Read Memory Code
#define WRITE 0x02   //Write Memory Code
#define RDID 0x9F    //Read Device ID#define MB85RS2M_ID 0x03487F04uint32_t MB85RS2M_ReadID(void);
uint8_t MB85RS2M_Init(void);
void MB85RS2M_Set_Write_Enable_Latch(void);
void MB85RS2M_Reset_Write_Enable_Latch(void);
void MB85RS2M_Write_Status_Register(uint8_t SRV);
uint8_t MB85RS2M_Read_Status_Register(void);
void MB85RS2M_Write_Memory(uint8_t * wd, uint32_t addr, uint32_t len);
void MB85RS2M_Read_Memory(uint8_t * rd, uint32_t addr, uint32_t len);#endif /* INC_MB85RS2M_H_ */

建立MB85RS2M.c源文件：

//Written by Pegasus Yu in 2023#include "MB85RS2M.h"
#include <string.h>#define SPI1_CS_L HAL_GPIO_WritePin(GPIOA, GPIO_PIN_4, GPIO_PIN_RESET)
#define SPI1_CS_H HAL_GPIO_WritePin(GPIOA, GPIO_PIN_4, GPIO_PIN_SET)
extern SPI_HandleTypeDef hspi1;
extern void PY_Delay_us_t(uint32_t Delay);uint32_t MB85RS2M_ReadID(void)
{uint8_t ftd[5];uint8_t frd[5];uint8_t Manufacturer_ID;uint8_t Continuation_Code;uint8_t Product_ID_L;uint8_t Product_ID_H;ftd[0]=RDID;SPI1_CS_L;HAL_SPI_TransmitReceive(&hspi1, ftd, frd, 5, 0xFFFFFFFF);SPI1_CS_H;Manufacturer_ID = frd[1];Continuation_Code = frd[2];Product_ID_L = frd[3];Product_ID_H = frd[4];return ((Product_ID_H<<24)|(Product_ID_L<<16)|(Continuation_Code<<8)|(Manufacturer_ID));
}uint8_t MB85RS2M_Init(void)
{uint8_t st = 0;for(uint8_t i=0; i<4; i++){if(MB85RS2M_ReadID()==MB85RS2M_ID){st = 1;break;}}return st;}/** WEL is reset after the following operations which means every write operation must follow once WREN operation MB85RS2M_Set_Write_Enable_Latch().* After power ON.* After WRDI command recognition.* At the rising edge of CS after WRSR command recognition.* At the rising edge of CS after WRITE command recognition.*/
void MB85RS2M_Set_Write_Enable_Latch(void)
{uint8_t cmd = WREN;SPI1_CS_L;HAL_SPI_Transmit(&hspi1, &cmd, 1, 0xFFFFFFFF);SPI1_CS_H;
}void MB85RS2M_Reset_Write_Enable_Latch(void)
{uint8_t cmd = WRDI;SPI1_CS_L;HAL_SPI_Transmit(&hspi1, &cmd, 1, 0xFFFFFFFF);SPI1_CS_H;
}void MB85RS2M_Write_Status_Register(uint8_t SRV)
{uint8_t data[2];data[0] = WRSR;data[1] = SRV;MB85RS2M_Set_Write_Enable_Latch();PY_Delay_us_t(2);SPI1_CS_L;HAL_SPI_Transmit(&hspi1, data, 2, 0xFFFFFFFF);SPI1_CS_H;
}uint8_t MB85RS2M_Read_Status_Register(void)
{uint8_t cmd[2];uint8_t data[2];uint8_t SRV;cmd[0] = RDSR;SPI1_CS_L;HAL_SPI_TransmitReceive(&hspi1, cmd, data, 2, 0xFFFFFFFF);SPI1_CS_H;SRV = data[1];return SRV;}/** wd: data buffer pointer* addr: address to operate for MB85RS2M* len: data length to be written*/void MB85RS2M_Write_Memory(uint8_t * wd, uint32_t addr, uint32_t len)
{uint8_t data[len+4];data[0] = WRITE;data[1] = (uint8_t)(addr>>16);data[2] = (uint8_t)(addr>>8);data[3] = (uint8_t)addr;memcpy(data+4, wd, len);MB85RS2M_Set_Write_Enable_Latch();PY_Delay_us_t(2);SPI1_CS_L;HAL_SPI_Transmit(&hspi1, data, len+4, 0xFFFFFFFF);SPI1_CS_H;
}/** rd: data buffer pointer* addr: address to operate for MB85RS2M* len: data length to be written*/void MB85RS2M_Read_Memory(uint8_t * rd, uint32_t addr, uint32_t len)
{uint8_t cmd[len+4];uint8_t data[len+4];cmd[0] = READ;cmd[1] = (uint8_t)(addr>>16);cmd[2] = (uint8_t)(addr>>8);cmd[3] = (uint8_t)addr;SPI1_CS_L;HAL_SPI_TransmitReceive(&hspi1, cmd, data , len+4, 0xFFFFFFFF);SPI1_CS_H;memcpy(rd, data+4, len);
}

USB接收命令的代码：
在这里插入图片描述

static int8_t CDC_Receive_FS(uint8_t* Buf, uint32_t *Len)
{/* USER CODE BEGIN 6 */extern uint8_t cmd;cmd = Buf[0];USBD_CDC_SetRxBuffer(&hUsbDeviceFS, &Buf[0]);USBD_CDC_ReceivePacket(&hUsbDeviceFS);return (USBD_OK);/* USER CODE END 6 */
}

对ffconf.h添加包含信息：
在这里插入图片描述

#include "main.h"
#include "stm32f4xx_hal.h"
#include "MB85RS2M.h"

修改user_diskio.c，对文件操作函数与底层I2C读写提供连接：

/* USER CODE BEGIN Header */
/********************************************************************************* @file    user_diskio.c* @brief   This file includes a diskio driver skeleton to be completed by the user.******************************************************************************* @attention** Copyright (c) 2023 STMicroelectronics.* All rights reserved.** This software is licensed under terms that can be found in the LICENSE file* in the root directory of this software component.* If no LICENSE file comes with this software, it is provided AS-IS.********************************************************************************//* USER CODE END Header */#ifdef USE_OBSOLETE_USER_CODE_SECTION_0
/** Warning: the user section 0 is no more in use (starting from CubeMx version 4.16.0)* To be suppressed in the future.* Kept to ensure backward compatibility with previous CubeMx versions when* migrating projects.* User code previously added there should be copied in the new user sections before* the section contents can be deleted.*/
/* USER CODE BEGIN 0 */
/* USER CODE END 0 */
#endif/* USER CODE BEGIN DECL *//* Includes ------------------------------------------------------------------*/
#include <string.h>
#include "ff_gen_drv.h"/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*//* Private variables ---------------------------------------------------------*/
/* Disk status */
static volatile DSTATUS Stat = STA_NOINIT;/* USER CODE END DECL *//* Private function prototypes -----------------------------------------------*/
DSTATUS USER_initialize (BYTE pdrv);
DSTATUS USER_status (BYTE pdrv);
DRESULT USER_read (BYTE pdrv, BYTE *buff, DWORD sector, UINT count);
#if _USE_WRITE == 1DRESULT USER_write (BYTE pdrv, const BYTE *buff, DWORD sector, UINT count);
#endif /* _USE_WRITE == 1 */
#if _USE_IOCTL == 1DRESULT USER_ioctl (BYTE pdrv, BYTE cmd, void *buff);
#endif /* _USE_IOCTL == 1 */Diskio_drvTypeDef  USER_Driver =
{USER_initialize,USER_status,USER_read,
#if  _USE_WRITEUSER_write,
#endif  /* _USE_WRITE == 1 */
#if  _USE_IOCTL == 1USER_ioctl,
#endif /* _USE_IOCTL == 1 */
};/* Private functions ---------------------------------------------------------*//*** @brief  Initializes a Drive* @param  pdrv: Physical drive number (0..)* @retval DSTATUS: Operation status*/
DSTATUS USER_initialize (BYTE pdrv           /* Physical drive nmuber to identify the drive */
)
{/* USER CODE BEGIN INIT *//**************************SELF DEFINITION PART************/uint8_t res;res = MB85RS2M_Init();if(res) return RES_OK;else return  STA_NOINIT;/**********************************************************/
/*Stat = STA_NOINIT;return Stat;*//* USER CODE END INIT */
}/*** @brief  Gets Disk Status* @param  pdrv: Physical drive number (0..)* @retval DSTATUS: Operation status*/
DSTATUS USER_status (BYTE pdrv       /* Physical drive number to identify the drive */
)
{/* USER CODE BEGIN STATUS *//**************************SELF DEFINITION PART************/switch (pdrv){case 0 :return RES_OK;case 1 :return RES_OK;case 2 :return RES_OK;default:return STA_NOINIT;}/**********************************************************//*Stat = STA_NOINIT;return Stat;*//* USER CODE END STATUS */
}/*** @brief  Reads Sector(s)* @param  pdrv: Physical drive number (0..)* @param  *buff: Data buffer to store read data* @param  sector: Sector address (LBA)* @param  count: Number of sectors to read (1..128)* @retval DRESULT: Operation result*/
DRESULT USER_read (BYTE pdrv,      /* Physical drive nmuber to identify the drive */BYTE *buff,     /* Data buffer to store read data */DWORD sector,   /* Sector address in LBA */UINT count      /* Number of sectors to read */
)
{/* USER CODE BEGIN READ *//**************************SELF DEFINITION PART************/uint16_t len;if( !count ){return RES_PARERR;  /* count不能等于0，否则返回参数错误*/}switch (pdrv){case 0:sector <<= 9; //Convert sector number to byte addresslen = count*512;MB85RS2M_Read_Memory((uint8_t *)buff, sector, len);return RES_OK;default:return RES_ERROR;}/**********************************************************//*return RES_OK;*//* USER CODE END READ */
}/*** @brief  Writes Sector(s)* @param  pdrv: Physical drive number (0..)* @param  *buff: Data to be written* @param  sector: Sector address (LBA)* @param  count: Number of sectors to write (1..128)* @retval DRESULT: Operation result*/
#if _USE_WRITE == 1
DRESULT USER_write (BYTE pdrv,          /* Physical drive nmuber to identify the drive */const BYTE *buff,   /* Data to be written */DWORD sector,       /* Sector address in LBA */UINT count          /* Number of sectors to write */
)
{/* USER CODE BEGIN WRITE *//* USER CODE HERE *//**************************SELF DEFINITION PART************/uint16_t len;if( !count ){return RES_PARERR;  /* count不能等于0，否则返回参数错误*/}switch (pdrv){case 0:sector <<= 9; //Convert sector number to byte addresslen = count*512;MB85RS2M_Write_Memory((uint8_t *)buff, sector, len);return RES_OK;default:return RES_ERROR;}/**********************************************************//*return RES_OK;*//* USER CODE END WRITE */
}
#endif /* _USE_WRITE == 1 *//*** @brief  I/O control operation* @param  pdrv: Physical drive number (0..)* @param  cmd: Control code* @param  *buff: Buffer to send/receive control data* @retval DRESULT: Operation result*/
#if _USE_IOCTL == 1
DRESULT USER_ioctl (BYTE pdrv,      /* Physical drive nmuber (0..) */BYTE cmd,       /* Control code */void *buff      /* Buffer to send/receive control data */
)
{/* USER CODE BEGIN IOCTL *//**************************SELF DEFINITION PART************/#define user_sector_byte_size 512DRESULT res;switch(cmd){case CTRL_SYNC:res=RES_OK;break;case GET_SECTOR_SIZE:*(WORD*)buff = user_sector_byte_size;res = RES_OK;break;case GET_BLOCK_SIZE:*(WORD*)buff = 4096/user_sector_byte_size;res = RES_OK;break;case GET_SECTOR_COUNT:*(DWORD*)buff = (256*1024/512);res = RES_OK;break;default:res = RES_PARERR;break;}return res;/**********************************************************//*DRESULT res = RES_ERROR;return res;*//* USER CODE END IOCTL */
}
#endif /* _USE_IOCTL == 1 */

然后在main.c里根据串口输入命令（16进制单字节）实现如下功能：
0x01. 读取FRAM ID
0x02. 装载FATS文件系统
0x03: 创建/打开文件并从头位置写入数据
0x04: 打开文件并从头位置读入数据
0x05: 创建/打开文件并从特定位置写入数据
0x06: 打开文件并从特定位置读入数据
完整的代码实现如下：

/* USER CODE BEGIN Header */
/********************************************************************************* @file           : main.c* @brief          : Main program body******************************************************************************* @attention** Copyright (c) 2023 STMicroelectronics.* All rights reserved.** This software is licensed under terms that can be found in the LICENSE file* in the root directory of this software component.* If no LICENSE file comes with this software, it is provided AS-IS.********************************************************************************/
//Written by Pegasus Yu in 2023
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "fatfs.h"
#include "usb_device.h"/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
#include <string.h>
#include "MB85RS2M.h"
/* USER CODE END Includes *//* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */
uint8_t CDC_Transmit_FS(uint8_t* Buf, uint16_t Len);
/* USER CODE END PTD *//* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
__IO float usDelayBase;
void PY_usDelayTest(void)
{__IO uint32_t firstms, secondms;__IO uint32_t counter = 0;firstms = HAL_GetTick()+1;secondms = firstms+1;while(uwTick!=firstms) ;while(uwTick!=secondms) counter++;usDelayBase = ((float)counter)/1000;
}void PY_Delay_us_t(uint32_t Delay)
{__IO uint32_t delayReg;__IO uint32_t usNum = (uint32_t)(Delay*usDelayBase);delayReg = 0;while(delayReg!=usNum) delayReg++;
}void PY_usDelayOptimize(void)
{__IO uint32_t firstms, secondms;__IO float coe = 1.0;firstms = HAL_GetTick();PY_Delay_us_t(1000000) ;secondms = HAL_GetTick();coe = ((float)1000)/(secondms-firstms);usDelayBase = coe*usDelayBase;
}void PY_Delay_us(uint32_t Delay)
{__IO uint32_t delayReg;__IO uint32_t msNum = Delay/1000;__IO uint32_t usNum = (uint32_t)((Delay%1000)*usDelayBase);if(msNum>0) HAL_Delay(msNum);delayReg = 0;while(delayReg!=usNum) delayReg++;
}
/* USER CODE END PD *//* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM *//* USER CODE END PM *//* Private variables ---------------------------------------------------------*/
SPI_HandleTypeDef hspi1;/* USER CODE BEGIN PV *//* USER CODE END PV *//* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_SPI1_Init(void);
/* USER CODE BEGIN PFP *//* USER CODE END PFP *//* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */
uint8_t cmd=0;          //for status controluint8_t FRAM_mount_status = 0; //FRAM fats mount status indication (0: unmount; 1: mount)
uint8_t FATS_Buff[_MAX_SS]; //Buffer for f_mkfs() operationFRESULT retFRAM;
FIL file;
FATFS *fs;UINT bytesread;
UINT byteswritten;
uint8_t rBuffer[20];      //Buffer for read
uint8_t WBuffer[20] ={1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20}; //Buffer for write#define user_sector_byte_size 512
uint8_t FRAMbuffer[user_sector_byte_size];extern char USERPath[4];
char * console;
/* USER CODE END 0 *//*** @brief  The application entry point.* @retval int*/
int main(void)
{/* USER CODE BEGIN 1 */FRAM_mount_status = 0;uint32_t FRAM_Read_Size;extern char USERPath[4];char * dpath = "0:"; //Disk Pathfor(uint8_t i=0; i<4; i++){USERPath[i] = *(dpath+i);}const TCHAR* filepath = "0:test.txt";char cchar[256];console = cchar;/* USER CODE END 1 *//* MCU Configuration--------------------------------------------------------*//* Reset of all peripherals, Initializes the Flash interface and the Systick. */HAL_Init();/* USER CODE BEGIN Init *//* USER CODE END Init *//* Configure the system clock */SystemClock_Config();/* USER CODE BEGIN SysInit *//* USER CODE END SysInit *//* Initialize all configured peripherals */MX_GPIO_Init();MX_USB_DEVICE_Init();MX_SPI1_Init();MX_FATFS_Init();/* USER CODE BEGIN 2 */PY_usDelayTest();PY_usDelayOptimize();/* USER CODE END 2 *//* Infinite loop *//* USER CODE BEGIN WHILE */while (1){if(cmd==1) //Read ID{cmd = 0;sprintf(console, "FRAM ID=MB85RS2MT\r\n\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}else if(cmd==2) //FRAM File System Mount{cmd = 0;retFRAM=f_mount(&USERFatFS, (TCHAR const*)USERPath, 1);if (retFRAM != FR_OK){sprintf(console, "File system mount failure: %d\r\n", retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);if(retFRAM==FR_NO_FILESYSTEM){sprintf(console, "No file system. Now to format......\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);retFRAM = f_mkfs((TCHAR const*)USERPath, FM_FAT, 1024, FATS_Buff, sizeof(FATS_Buff)); //FRAM formattingif(retFRAM == FR_OK){sprintf(console, "FRAM formatting success!\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}else{sprintf(console, "FRAM formatting failure!\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}}}else{FRAM_mount_status = 1;sprintf(console, "File system mount success\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}}else if(cmd==3) //File creation and write{cmd = 0;if(FRAM_mount_status==0){sprintf(console, "\r\nFRAM File system not mounted: %d\r\n",retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}else{retFRAM = f_open( &file, filepath, FA_CREATE_ALWAYS | FA_WRITE );  //Open or create fileif(retFRAM == FR_OK){sprintf(console, "\r\nFile open or creation successful\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);retFRAM = f_write( &file, (const void *)WBuffer, sizeof(WBuffer), &byteswritten); //Write dataif(retFRAM == FR_OK){sprintf(console, "\r\nFile write successful\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}else{sprintf(console, "\r\nFile write error: %d\r\n",retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}f_close(&file);   //Close file}else{sprintf(console, "\r\nFile open or creation error %d\r\n",retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}}}else if(cmd==4) //File read{cmd = 0;if(FRAM_mount_status==0){sprintf(console, "\r\nFRAM File system not mounted: %d\r\n",retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}else{retFRAM = f_open( &file, filepath, FA_OPEN_EXISTING | FA_READ); //Open fileif(retFRAM == FR_OK){sprintf(console, "\r\nFile open successful\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);retFRAM = f_read( &file, (void *)rBuffer, sizeof(rBuffer), &bytesread); //Read dataif(retFRAM == FR_OK){sprintf(console, "\r\nFile read successful\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);PY_Delay_us_t(200000);FRAM_Read_Size = sizeof(rBuffer);for(uint16_t i = 0;i < FRAM_Read_Size;i++){sprintf(console, "%d ", rBuffer[i]);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}sprintf(console, "\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}else{sprintf(console, "\r\nFile read error: %d\r\n", retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}f_close(&file); //Close file}else{sprintf(console, "\r\nFile open error: %d\r\n", retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}}}else if(cmd==5) //File locating write{cmd = 0;if(FRAM_mount_status==0){sprintf(console, "\r\nFRAM File system not mounted: %d\r\n",retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}else{retFRAM = f_open( &file, filepath, FA_CREATE_ALWAYS | FA_WRITE);  //Open or create fileif(retFRAM == FR_OK){sprintf(console, "\r\nFile open or creation successful\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);retFRAM=f_lseek( &file, f_tell(&file) + sizeof(WBuffer) ); //move file operation pointer, f_tell(&file) gets file head locatingif(retFRAM == FR_OK){retFRAM = f_write( &file, (const void *)WBuffer, sizeof(WBuffer), &byteswritten);if(retFRAM == FR_OK){sprintf(console, "\r\nFile locating write successful\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}else{sprintf(console, "\r\nFile locating write error: %d\r\n", retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}}else{sprintf(console, "\r\nFile pointer error: %d\r\n",retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}f_close(&file);   //Close file}else{sprintf(console, "\r\nFile open or creation error %d\r\n",retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}}}else if(cmd==6) //File locating read{cmd = 0;if(FRAM_mount_status==0){sprintf(console, "\r\nFRAM File system not mounted: %d\r\n",retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}else{retFRAM = f_open(&file, filepath, FA_OPEN_EXISTING | FA_READ); //Open fileif(retFRAM == FR_OK){sprintf(console, "\r\nFile open successful\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);retFRAM =  f_lseek(&file,f_tell(&file)+ sizeof(WBuffer)/2); //move file operation pointer, f_tell(&file) gets file head locatingif(retFRAM == FR_OK){retFRAM = f_read( &file, (void *)rBuffer, sizeof(rBuffer), &bytesread);if(retFRAM == FR_OK){sprintf(console, "\r\nFile locating read successful\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);PY_Delay_us_t(200000);FRAM_Read_Size = sizeof(rBuffer);for(uint16_t i = 0;i < FRAM_Read_Size;i++){sprintf(console, "%d ",rBuffer[i]);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}sprintf(console, "\r\n");while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}else{sprintf(console, "\r\nFile locating read error: %d\r\n",retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}}else{sprintf(console, "\r\nFile pointer error: %d\r\n",retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}f_close(&file);}else{sprintf(console, "\r\nFile open error: %d\r\n",retFRAM);while( CDC_Transmit_FS((uint8_t*)console, strlen(console)) == USBD_BUSY ) PY_Delay_us_t(1);}}}PY_Delay_us_t(100);/* USER CODE END WHILE *//* USER CODE BEGIN 3 */}/* USER CODE END 3 */
}/*** @brief System Clock Configuration* @retval None*/
void SystemClock_Config(void)
{RCC_OscInitTypeDef RCC_OscInitStruct = {0};RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};/** Configure the main internal regulator output voltage*/__HAL_RCC_PWR_CLK_ENABLE();__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);/** Initializes the RCC Oscillators according to the specified parameters* in the RCC_OscInitTypeDef structure.*/RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;RCC_OscInitStruct.HSEState = RCC_HSE_ON;RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;RCC_OscInitStruct.PLL.PLLM = 25;RCC_OscInitStruct.PLL.PLLN = 336;RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4;RCC_OscInitStruct.PLL.PLLQ = 7;if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK){Error_Handler();}/** Initializes the CPU, AHB and APB buses clocks*/RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK){Error_Handler();}
}/*** @brief SPI1 Initialization Function* @param None* @retval None*/
static void MX_SPI1_Init(void)
{/* USER CODE BEGIN SPI1_Init 0 *//* USER CODE END SPI1_Init 0 *//* USER CODE BEGIN SPI1_Init 1 *//* USER CODE END SPI1_Init 1 *//* SPI1 parameter configuration*/hspi1.Instance = SPI1;hspi1.Init.Mode = SPI_MODE_MASTER;hspi1.Init.Direction = SPI_DIRECTION_2LINES;hspi1.Init.DataSize = SPI_DATASIZE_8BIT;hspi1.Init.CLKPolarity = SPI_POLARITY_LOW;hspi1.Init.CLKPhase = SPI_PHASE_1EDGE;hspi1.Init.NSS = SPI_NSS_SOFT;hspi1.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_8;hspi1.Init.FirstBit = SPI_FIRSTBIT_MSB;hspi1.Init.TIMode = SPI_TIMODE_DISABLE;hspi1.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;hspi1.Init.CRCPolynomial = 10;if (HAL_SPI_Init(&hspi1) != HAL_OK){Error_Handler();}/* USER CODE BEGIN SPI1_Init 2 *//* USER CODE END SPI1_Init 2 */}/*** @brief GPIO Initialization Function* @param None* @retval None*/
static void MX_GPIO_Init(void)
{GPIO_InitTypeDef GPIO_InitStruct = {0};
/* USER CODE BEGIN MX_GPIO_Init_1 */
/* USER CODE END MX_GPIO_Init_1 *//* GPIO Ports Clock Enable */__HAL_RCC_GPIOH_CLK_ENABLE();__HAL_RCC_GPIOA_CLK_ENABLE();/*Configure GPIO pin Output Level */HAL_GPIO_WritePin(GPIOA, GPIO_PIN_2|GPIO_PIN_3|GPIO_PIN_4, GPIO_PIN_SET);/*Configure GPIO pins : PA2 PA3 PA4 */GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3|GPIO_PIN_4;GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;GPIO_InitStruct.Pull = GPIO_NOPULL;GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);/* USER CODE BEGIN MX_GPIO_Init_2 */
/* USER CODE END MX_GPIO_Init_2 */
}/* USER CODE BEGIN 4 *//* USER CODE END 4 *//*** @brief  This function is executed in case of error occurrence.* @retval None*/
void Error_Handler(void)
{/* USER CODE BEGIN Error_Handler_Debug *//* User can add his own implementation to report the HAL error return state */__disable_irq();while (1){}/* USER CODE END Error_Handler_Debug */
}#ifdef  USE_FULL_ASSERT
/*** @brief  Reports the name of the source file and the source line number*         where the assert_param error has occurred.* @param  file: pointer to the source file name* @param  line: assert_param error line source number* @retval None*/
void assert_failed(uint8_t *file, uint32_t line)
{/* USER CODE BEGIN 6 *//* User can add his own implementation to report the file name and line number,ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) *//* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

STM32例程测试

串口指令0x01测试效果如下：
在这里插入图片描述
串口指令0x02测试效果如下：
在这里插入图片描述
串口指令0x03测试效果如下：
在这里插入图片描述
串口指令0x04测试效果如下：
在这里插入图片描述
串口指令0x05测试效果如下：
在这里插入图片描述
串口指令0x06测试效果如下：
在这里插入图片描述

STM32例程下载

STM32F401CCU6 SPI总线FATS读写FRAM MB85RS2M例程下载

–End–

本文来自互联网用户投稿，该文观点仅代表作者本人，不代表本站立场。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如若转载，请注明出处：http://www.rhkb.cn/news/240651.html

如若内容造成侵权/违法违规/事实不符，请联系长河编程网进行投诉反馈email:809451989@qq.com，一经查实，立即删除！

相关文章

在分类任务中准确率（accuracy）、精确率（precision）、召回率（recall）和 F1 分数是常用的性能指标，如何在python中使用呢？

在分类任务中准确率（accuracy）、精确率（precision）、召回率（recall）和 F1 分数是常用的性能指标，如何在python中使用呢？

在机器学习和数据科学中&#xff0c;准确率&#xff08;accuracy&#xff09;、精确率&#xff08;precision&#xff09;、召回率&#xff08;recall&#xff09;和 F1 分数是常用的性能指标&#xff0c;用于评估分类模型的性能。 1. 准确率&#xff08;Accuracy&#xff09;…
阅读更多...
LeetCode、2542. 最大子序列的分数【中等，排序+小顶堆】

LeetCode、2542. 最大子序列的分数【中等，排序+小顶堆】

文章目录 前言LeetCode、2542. 最大子序列的分数【中等&#xff0c;排序小顶堆】题目及类型思路及代码实现 资料获取 前言 博主介绍&#xff1a;✌目前全网粉丝2W&#xff0c;csdn博客专家、Java领域优质创作者&#xff0c;博客之星、阿里云平台优质作者、专注于Java后端技术领…
阅读更多...
FindMy技术与相机结合

FindMy技术与相机结合

FindMy是苹果公司提供的设备追踪服务&#xff0c;用来帮助用户定位丢失的设备。自苹果公司开放Findmy网络之后&#xff0c;FindMy技术便与各种生活设备相结合&#xff0c;比如与相机的结合。 想象一下&#xff0c;你正在外出办事或者旅行时&#xff0c;突然意识到相机丢了&…
阅读更多...
esxi-vSphere

esxi-vSphere

esxi安装 vCenterServer 安装 给予 esxi,一般一个esxi &#xff0c;就安装一个 vCenter 关于 vCenter Server 安装和设置 比较清晰教程&#xff1a; 【VCSA 8】安装vCenter Server Appliance(VCSA) 8.0-CSDN博客 vcsa 的安装 不是在 esxi 页面添加虚拟机方式&#xff0c;而是…
阅读更多...
前端（二）VUE功能集锦

前端（二）VUE功能集锦

一、引言 作者开发工具平台的时候&#xff0c;用到了vue和element-ui&#xff0c;这里写一下各种功能使用&#xff0c;有的是绕点弯路&#xff0c;有的是需要结合实现需要自己改写一下。 二、功能 先看看环境&#xff0c;作者后端是SpringBoot&#xff0c;前端是VUEElementUI&a…
阅读更多...
水质净化厂物联网远程监控系统解决方案

水质净化厂物联网远程监控系统解决方案

水质净化厂物联网远程监控系统解决方案 随着科技的不断发展&#xff0c;物联网技术逐渐走进我们的生活。在水质净化厂中&#xff0c;物联网技术可以应用于远程监控系统&#xff0c;实现对水质净化过程的实时监测和数据分析&#xff0c;从而提高净化效率和管理水平。 一、需求分…
阅读更多...
操作系统课程设计-内存管理

操作系统课程设计-内存管理

目录 前言 1 实验题目 2 实验目的 3 实验内容 3.1 步骤 3.2 关键代码 3.2.1 显示虚拟内存的基本信息 3.2.2 遍历当前进程的虚拟内存 4 实验结果与分析 5 代码 前言 本实验为课设内容&#xff0c;博客内容为部分报告内容&#xff0c;仅为大家提供参考&#xff0c;请勿直…
阅读更多...
首届PolarDB开发者大会在京举办，阿里云李飞飞：云数据库加速迈向智能化

首届PolarDB开发者大会在京举办，阿里云李飞飞：云数据库加速迈向智能化

1月17日&#xff0c;阿里云PolarDB开发者大会在京举办&#xff0c;中国首款自研云原生数据库PolarDB发布“三层分离”新版本&#xff0c;基于智能决策实现查询性能10倍提升、节省50%成本。此外&#xff0c;阿里云全新推出数据库场景体验馆、训练营等系列新举措&#xff0c;广大…
阅读更多...
QT第六天

QT第六天

要求&#xff1a;使用QT绘图&#xff0c;完成仪表盘绘制&#xff0c;如下图。 素材 运行效果&#xff1a; 代码&#xff1a; widget.h #ifndef WIDGET_H #define WIDGET_H#include <QWidget> #include <QPainter> #include <QPen>QT_BEGIN_NAMESPACE name…
阅读更多...
S/MIME电子邮件证书申请指南

S/MIME电子邮件证书申请指南

近年来&#xff0c;邮件安全问题日益突出&#xff0c;电子邮件成为诈骗、勒索软件攻击的重灾区。恶意邮件的占比屡创新高&#xff0c;邮件泄密事件更是比比皆是。在如此严峻的网络安全形势下&#xff0c;使用S/MIME电子邮件证书进行邮件收发是当今最佳的邮件安全解决方案之一。…
阅读更多...
申 论 一

申 论 一

阅读更多...
Apache Doris (六十四）： Flink Doris Connector - (1)-源码编译

Apache Doris (六十四）： Flink Doris Connector - (1)-源码编译

🏡 个人主页：IT贫道-CSDN博客 🚩 私聊博主：私聊博主加WX好友，获取更多资料哦~ 🔔 博主个人B栈地址：豹哥教你学编程的个人空间-豹哥教你学编程个人主页-哔哩哔哩视频 目录 1. Flink与Doris版本兼容
阅读更多...
结构体内存对齐的跨平台做法

结构体内存对齐的跨平台做法

作者&#xff1a;朱金灿 来源&#xff1a;clever101的专栏 为什么大多数人学不会人工智能编程&#xff1f;>>> 之前写了一篇文章&#xff1a;使用标准C库读文件时需要注意的一个问题&#xff0c;今天发现是错误的。正确的做法是使用#pragma pack预处理指令。示例程序…
阅读更多...
无需信用卡注册美区Apple ID指南

无需信用卡注册美区Apple ID指南

第一步 准备工作 1、一个没有注册过AppleID的邮箱&#xff0c;建议最好是Gmail邮箱 2、一个苹果手机&#xff0c;当然这个是必须的 3、需要科学上网 第二步 苹果网站注册 为了避免cookie的干扰&#xff0c;最好是在无痕模式下打开以上网页&#xff0c;创建你的AppleID&#…
阅读更多...
【云原生】springboot 整合 OpenTelemetry

【云原生】springboot 整合 OpenTelemetry

目录 一、前言 二、应用可观测性概述 2.1 什么是可观测性 2.2 可观测性三大指标 2.2.1 指标&#xff08;Metrics&#xff09; 2.2.2 日志&#xff08;log&#xff09; 2.2.3 追踪(Traces) 三、OpenTelemetry 介绍 3.1 什么是OpenTelemetry 3.2 OpenTelemetry架构和组件…
阅读更多...
LiveGBS流媒体平台GB/T28181功能-基础配置接入控制白名单黑名单配置控制设备安全接入设备单独配置接入密码

LiveGBS流媒体平台GB/T28181功能-基础配置接入控制白名单黑名单配置控制设备安全接入设备单独配置接入密码

LiveGBS基础配置接入控制白名单黑名单配置控制设备安全接入设备单独配置接入密码 1、白名单配置应用场景2、接入控制2.1、白名单2.2、黑名单 3、搭建GB28181视频直播平台 1、白名单配置应用场景 LiveGBS国标流媒体服务&#xff0c;支持白名单配置。 可在设备注册前&#xff0…
阅读更多...
最新版git2.43安装、记住用户名和密码以及tortoisegit2.15使用

最新版git2.43安装、记住用户名和密码以及tortoisegit2.15使用

一、下载git 打开git官网地址&#xff1a;https://git-scm.com/进行下载 下载完安装&#xff0c;一直next就好&#xff0c;如果愿意就可以改下安装路径&#xff0c;改在d盘。 具体可以参考&#xff1a;git安装教程 二、安装完下载小乌龟以及中文语言包 下载地址&#xff1a;…
阅读更多...
小程序中使用上传图片，显示、删除、预览

小程序中使用上传图片，显示、删除、预览

一、功能介绍 需要哦用户点击加号上传图片&#xff0c;并展示所上传图片和能够删除和预览 二、功能实现 采用的uniapp&#xff0c;创建了一个view容器包裹加号图标和展示的图片。 内部展示图片超过9张时候&#xff0c;加号图片隐藏 <view class"img-list">/…
阅读更多...
12AOP面向切面编程/GoF之代理模式

12AOP面向切面编程/GoF之代理模式

先看一个例子&#xff1a; 声明一个接口&#xff1a; // - * / 运算的标准接口! public interface Calculator {int add(int i, int j);int sub(int i, int j);int mul(int i, int j);int div(int i, int j); }实现该接口&#xff1a; package com.sunsplanter.prox…
阅读更多...
私有仓库工具Nexus Maven如何部署并实现远程访问管理界面

私有仓库工具Nexus Maven如何部署并实现远程访问管理界面

文章目录 1. Docker安装Nexus2. 本地访问Nexus3. Linux安装Cpolar4. 配置Nexus界面公网地址5. 远程访问 Nexus界面6. 固定Nexus公网地址7. 固定地址访问Nexus Nexus是一个仓库管理工具&#xff0c;用于管理和组织软件构建过程中的依赖项和构件。它与Maven密切相关&#xff0c;可…
阅读更多...
最新文章
推荐文章

Copyright @ 2022~2023