本博文是博文 https://blog.csdn.net/wenhao_ir/article/details/145547974 的分支。

本博文用来记录由NXP提供的FSL Yocto Project Community BSP构建出的镜像文件imx-image-full-imx6ull14x14evk-20201209093926.rootfs.wic启动百问网的IMX6ULL_PRO 开发板时串口终端的输出信息。

u-boot阶段的日志输出

U-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 25C
Reset cause: POR
Model: i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment[*]-Video Link 0 (480 x 272)[0] lcdif@21c8000, video
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:   Could not get PHY for FEC1: addr 1
Could not get PHY for FEC1: addr 1
Get shared mii bus on ethernet@2188000
Could not get PHY for FEC1: addr 2
Get shared mii bus on ethernet@2188000
undefined instruction
pc : [<00000084>]          lr : [<9ef9a047>]
reloc pc : [<e888a084>]    lr : [<87824047>]
sp : 9df6b718  ip : 00000020     fp : 00000017
r10: 9df93400  r9 : 9df73ed0     r8 : 9df754b8
r7 : 9df75458  r6 : 00000006     r5 : 00000004  r4 : 9df76548
r3 : 00000048  r2 : 00000006     r1 : 00000004  r0 : 9df76548
Flags: nzCv  IRQs off  FIQs off  Mode SVC_32
Code: 00000000 00000000 00000000 00000011 (79706f43) 
Resetting CPU ...resetting ...U-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 26C
Reset cause: POR
Model: i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment[*]-Video Link 0 (480 x 272)[0] lcdif@21c8000, video
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:   
Error: ethernet@20b4000 address not set.Error: ethernet@20b4000 address not set.Error: ethernet@20b4000 address not set.
FEC: can't find phy-handleError: ethernet@20b4000 address not set.
Could not get PHY for FEC0: addr 2Error: ethernet@20b4000 address not set.
FEC: can't find phy-handleError: ethernet@20b4000 address not set.
Could not get PHY for FEC0: addr 2
No ethernet found.Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
9004056 bytes read in 432 ms (19.9 MiB/s)
Booting from mmc ...
35579 bytes read in 17 ms (2 MiB/s)
1056900 bytes read in 60 ms (16.8 MiB/s)
## Booting kernel from Legacy Image at 84000000 ...Image Name:   Image Type:   ARM Linux Kernel Image (uncompressed)Data Size:    1056836 Bytes = 1 MiBLoad Address: 84000000Entry Point:  84000000Verifying Checksum ... OK
## Flattened Device Tree blob at 83000000Booting using the fdt blob at 0x83000000Loading Kernel ImageUsing Device Tree in place at 83000000, end 8300bafa
Modify /soc/aips-bus@2200000/epdc@228c000:status disabled
ft_system_setup for mx6Starting kernel .........说明：Starting kernel之后是Kernel(内核心)的输出。

内核(kernel)启动阶段的日志输出

说明：Starting kernel之前为u-boot的输出Starting kernel ...E/TC:0 0 plat_rng_init:188 Warning: seeding RNG with zeroes
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.47-2.2.0+g5ec03d06f54e (oe-user@oe-host) (gcc version 9.2.0 (GCC)) #1 SMP PREEMPT Wed Dec 9 10:05:01 UTC 2020
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Freescale i.MX6 ULL 14x14 EVK Board
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Reserved memory: created CMA memory pool at 0x96000000, size 160 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 15 pages/cpu s32076 r8192 d21172 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 121728
[    0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 302988K/491520K available (12288K kernel code, 576K rwdata, 4272K rodata, 1024K init, 433K bss, 24692K reserved, 163840K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x2c8/0x488 with crng_init=0
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000017] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000055] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.002964] Console: colour dummy device 80x30
[    0.003036] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.003071] pid_max: default: 32768 minimum: 301
[    0.003456] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.003493] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.005236] CPU: Testing write buffer coherency: ok
[    0.005981] CPU0: update cpu_capacity 1024
[    0.006015] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.060586] Setting up static identity map for 0x80100000 - 0x80100060
[    0.080564] rcu: Hierarchical SRCU implementation.
[    0.120736] smp: Bringing up secondary CPUs ...
[    0.120771] smp: Brought up 1 node, 1 CPU
[    0.120794] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[    0.120810] CPU: All CPU(s) started in SVC mode.
[    0.121701] devtmpfs: initialized
[    0.141230] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.142225] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.142278] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[    0.155625] pinctrl core: initialized pinctrl subsystem
[    0.158149] NET: Registered protocol family 16
[    0.178310] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.181032] cpuidle: using governor menu
[    0.198965] vdd3p0: supplied by regulator-dummy
[    0.200334] cpu: supplied by regulator-dummy
[    0.201826] vddsoc: supplied by regulator-dummy
[    0.226512] No ATAGs?
[    0.226650] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.226687] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.231068] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[    0.231871] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/aips-bus@2200000/iomuxc-snvs@2290000
[    0.231912] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[    0.234701] imx mu driver is registered.
[    0.235754] imx rpmsg driver is registered.
[    0.318584] vgaarb: loaded
[    0.320521] SCSI subsystem initialized
[    0.323261] usbcore: registered new interface driver usbfs
[    0.323396] usbcore: registered new interface driver hub
[    0.323642] usbcore: registered new device driver usb
[    0.326953] i2c i2c-0: IMX I2C adapter registered
[    0.329053] i2c i2c-1: IMX I2C adapter registered
[    0.329965] mc: Linux media interface: v0.10
[    0.330085] videodev: Linux video capture interface: v2.00
[    0.330221] pps_core: LinuxPPS API ver. 1 registered
[    0.330243] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.330295] PTP clock support registered
[    0.333616] MIPI CSI2 driver module loaded
[    0.333761] Advanced Linux Sound Architecture Driver Initialized.
[    0.335624] Bluetooth: Core ver 2.22
[    0.335760] NET: Registered protocol family 31
[    0.335780] Bluetooth: HCI device and connection manager initialized
[    0.335816] Bluetooth: HCI socket layer initialized
[    0.335842] Bluetooth: L2CAP socket layer initialized
[    0.335902] Bluetooth: SCO socket layer initialized
[    0.337068] clocksource: Switched to clocksource mxc_timer1
[    0.337503] VFS: Disk quotas dquot_6.6.0
[    0.337718] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.361223] thermal_sys: Registered thermal governor 'step_wise'
[    0.361882] NET: Registered protocol family 2
[    0.363254] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.363341] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.363453] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.363611] TCP: Hash tables configured (established 4096 bind 4096)
[    0.363830] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.363898] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.364308] NET: Registered protocol family 1
[    0.395888] RPC: Registered named UNIX socket transport module.
[    0.395923] RPC: Registered udp transport module.
[    0.395941] RPC: Registered tcp transport module.
[    0.395956] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.407499] PCI: CLS 0 bytes, default 64
[    0.409054] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.412760] Bus freq driver module loaded
[    0.415255] Initialise system trusted keyrings
[    0.415825] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.443583] NFS: Registering the id_resolver key type
[    0.443659] Key type id_resolver registered
[    0.443679] Key type id_legacy registered
[    0.443782] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.445052] fuse: init (API version 7.31)
[    0.536397] Key type asymmetric registered
[    0.536432] Asymmetric key parser 'x509' registered
[    0.536499] io scheduler mq-deadline registered
[    0.536519] io scheduler kyber registered
[    0.557380] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator
[    0.565592] mxsfb 21c8000.lcdif: 21c8000.lcdif supply lcd not found, using dummy regulator
[    0.676713] sii902x bound to mxs-lcdif from 21c8000.lcdif
[    0.680895] Console: switching to colour frame buffer device 60x34
[    0.778920] mxsfb 21c8000.lcdif: initialized
[    0.789186] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[    0.789226] imx-sdma 20ec000.sdma: Falling back to sysfs fallback for: imx/sdma/sdma-imx6q.bin
[    0.793695] mxs-dma 1804000.dma-apbh: initialized
[    0.801726] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX
[    1.543057] printk: console [ttymxc0] enabled
[    1.549853] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 67, base_baud = 5000000) is a IMX
[    1.594112] imx_rngc 2284000.rng: Freescale RNGC registered.
[    1.600625] imx sema4 driver is registered.
[    1.643398] brd: module loaded
[    1.667305] loop: module loaded
[    1.673265] imx ahci driver is registered.
[    1.685699] spi-nor spi4.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff
[    1.694170] gpio@0 enforce active low on chipselect handle
[    1.704648] libphy: Fixed MDIO Bus: probed
[    1.710312] CAN device driver interface
[    1.719335] pps pps0: new PPS source ptp0
[    1.725696] fec 20b4000.ethernet: Invalid MAC address: 00:00:00:00:00:00
[    1.732600] fec 20b4000.ethernet: Using random MAC address: 4a:08:82:18:85:57
[    1.740684] libphy: fec_enet_mii_bus: probed
[    1.745291] mdio_bus 20b4000.ethernet-1: MDIO device at address 2 is missing.
[    1.765974] fec 20b4000.ethernet eth0: registered PHC device 0
[    1.774999] pps pps1: new PPS source ptp1
[    1.781706] fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
[    1.788731] fec 2188000.ethernet: Using random MAC address: 1a:20:70:cc:29:6f
[    1.798224] fec 2188000.ethernet eth1: registered PHC device 1
[    1.804856] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.810916] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.818331] usbcore: registered new interface driver r8152
[    1.823985] usbcore: registered new interface driver lan78xx
[    1.829910] usbcore: registered new interface driver asix
[    1.835434] usbcore: registered new interface driver ax88179_178a
[    1.841713] usbcore: registered new interface driver cdc_ether
[    1.847772] usbcore: registered new interface driver smsc95xx
[    1.853640] usbcore: registered new interface driver net1080
[    1.859476] usbcore: registered new interface driver cdc_subset
[    1.865503] usbcore: registered new interface driver zaurus
[    1.871245] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    1.878858] usbcore: registered new interface driver cdc_ncm
[    1.884548] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.891146] ehci-pci: EHCI PCI platform driver
[    1.895715] ehci-mxc: Freescale On-Chip EHCI Host driver
[    1.902142] usbcore: registered new interface driver usb-storage
[    1.912694] imx_usb 2184000.usb: No over current polarity defined
[    1.919091] imx_usb 2184000.usb: 2184000.usb supply vbus not found, using dummy regulator
[    2.219492] random: fast init done
[    2.555277] mxs_phy 20c9000.usbphy: Data pin can't make good contact.
[    2.574865] imx_usb 2184200.usb: 2184200.usb supply vbus not found, using dummy regulator
[    2.587874] ci_hdrc ci_hdrc.1: EHCI Host Controller
[    2.592899] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[    2.627199] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[    2.633122] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[    2.641514] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.648820] usb usb1: Product: EHCI Host Controller
[    2.653731] usb usb1: Manufacturer: Linux 5.4.47-2.2.0+g5ec03d06f54e ehci_hcd
[    2.660937] usb usb1: SerialNumber: ci_hdrc.1
[    2.666842] hub 1-0:1.0: USB hub found
[    2.670912] hub 1-0:1.0: 1 port detected
[    2.690985] input: 20cc000.snvs:snvs-powerkey as /devices/soc0/soc/2000000.aips-bus/20cc000.snvs/20cc000.snvs:snvs-powerkey/input/input0
[    2.707358] input: iMX6UL Touchscreen Controller as /devices/soc0/soc/2000000.aips-bus/2040000.tsc/input/input1
[    2.720968] read sensor who am i (0x0)error !
[    2.725415] fxls8471: probe of 0-001e failed with error -22
[    2.736629] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc0
[    2.743264] i2c /dev entries driver
[    2.750794] pxp-v4l2 pxp_v4l2: initialized
[    2.756064] syscon-poweroff 20cc000.snvs:snvs-poweroff: pm_power_off already claimed (ptrval) psci_sys_poweroff
[    2.766359] syscon-poweroff: probe of 20cc000.snvs:snvs-poweroff failed with error -16
[    2.776426] mag3110 0-000e: 0-000e supply vdd not found, using dummy regulator
[    2.784273] mag3110 0-000e: 0-000e supply vddio not found, using dummy regulator
[    2.791970] mag3110 0-000e: check mag3110 chip ID
[    2.797166] mag3110 0-000e: read chip ID 0xfffffffa is not equal to 0xc4!
[    2.804300] mag3110: probe of 0-000e failed with error -22
[    2.813252] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[    2.820995] Bluetooth: HCI UART driver ver 2.3
[    2.825495] Bluetooth: HCI UART protocol H4 registered
[    2.830951] Bluetooth: HCI UART protocol BCSP registered
[    2.836436] Bluetooth: HCI UART protocol LL registered
[    2.841836] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    2.848261] Bluetooth: HCI UART protocol Marvell registered
[    2.854009] usbcore: registered new interface driver btusb
[    2.861462] sdhci: Secure Digital Host Controller Interface driver
[    2.867784] sdhci: Copyright(c) Pierre Ossman
[    2.872168] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.881013] sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO
[    2.931007] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[    3.002357] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
[    3.014001] caam-snvs 20cc000.caam-snvs: violation handlers armed - init state
[    3.028289] usbcore: registered new interface driver usbhid
[    3.033910] usbhid: USB HID core driver
[    3.038083] usb 1-1: new high-speed USB device number 2 using ci_hdrc
[    3.052385] optee: probing for conduit method from DT.
[    3.058109] optee: revision 3.10 (b3914e54)
[    3.058953] optee: dynamic shared memory is enabled
[    3.070242] optee: initialized driver
[    3.078312] mmc0: error -110 whilst initialising SD card
[    3.105504] fsl-sai 202c000.sai: failed to get mclk0 clock: -2
[    3.124891] debugfs: Directory '202c000.sai' with parent 'wm8960-audio' already present!
[    3.135319] imx-wm8960 sound-wm8960: wm8960-hifi <-> 202c000.sai mapping ok
[    3.151155] imx-wm8960 sound-wm8960: snd-soc-dummy-dai <-> 2034000.asrc mapping ok
[    3.161909] imx-wm8960 sound-wm8960: wm8960-hifi <-> 202c000.sai mapping ok
[    3.169048] mmc1: new DDR MMC card at address 0001
[    3.186193] mmcblk1: mmc1:0001 S40004 3.64 GiB 
[    3.192070] mmcblk1boot0: mmc1:0001 S40004 partition 1 4.00 MiB
[    3.198935] mmcblk1boot1: mmc1:0001 S40004 partition 2 4.00 MiB
[    3.205428] mmcblk1rpmb: mmc1:0001 S40004 partition 3 4.00 MiB, chardev (244:0)
[    3.228998]  mmcblk1: p1 p2 p3
[    3.237913] usb 1-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[    3.247371] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    3.259926] hub 1-1:1.0: USB hub found
[    3.264189] hub 1-1:1.0: 4 ports detected
[    3.305647] NET: Registered protocol family 26
[    3.312235] NET: Registered protocol family 10
[    3.329817] Segment Routing with IPv6
[    3.334087] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.342153] NET: Registered protocol family 17
[    3.346923] can: controller area network core (rev 20170425 abi 9)
[    3.353676] NET: Registered protocol family 29
[    3.358467] can: raw protocol (rev 20170425)
[    3.362990] can: broadcast manager protocol (rev 20170425 t)
[    3.368965] can: netlink gateway (rev 20190810) max_hops=1
[    3.375322] Bluetooth: RFCOMM TTY layer initialized
[    3.380995] Bluetooth: RFCOMM socket layer initialized
[    3.386796] Bluetooth: RFCOMM ver 1.11
[    3.391271] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    3.396703] Bluetooth: BNEP filters: protocol multicast
[    3.402149] Bluetooth: BNEP socket layer initialized
[    3.407204] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.413183] Bluetooth: HIDP socket layer initialized
[    3.418351] lib80211: common routines for IEEE802.11 drivers
[    3.424138] Key type dns_resolver registered
[    3.460686] Registering SWP/SWPB emulation handler
[    3.466747] Loading compiled-in X.509 certificates
[    3.504315] regulator-can-3v3 GPIO handle specifies active low - ignored
[    3.517733] imx_thermal tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C
[    3.528683] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:00:00 UTC (0)
[    3.538178] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    3.549868] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    3.556658] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    3.565639] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
[    3.573888] ALSA device list:
[    3.576884]   #0: wm8960-audio
[    3.580677] Waiting for root device /dev/mmcblk0p2...
[   33.767201] VSD_3V3: disabling
[   33.770324] can-3v3: disabling
[   64.487623] cfg80211: failed to load regulatory.db
[   64.493459] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[   64.503308] imx-sdma 20ec000.sdma: Falling back to sysfs fallback for: imx/sdma/sdma-imx6q.bin
U-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 25C
Reset causU-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 28C
Reset cause: POR
Model: i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment[*]-Video Link 0 (480 x 272)[0] lcdif@21c8000, video
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:   Could not get PHY for FEC1: addr 1
Could not get PHY for FEC1: addr 1
Get shared mii bus on ethernet@2188000
Could not get PHY for FEC1: addr 2
Get shared mii bus on ethernet@2188000
undefined instruction
pc : [<00000084>]          lr : [<9ef9a047>]
reloc pc : [<e888a084>]    lr : [<87824047>]
sp : 9df6b718  ip : 00000020     fp : 00000017
r10: 9df93400  r9 : 9df73ed0     r8 : 9df754b8
r7 : 9df75458  r6 : 00000006     r5 : 00000004  r4 : 9df76548
r3 : 00000048  r2 : 00000006     r1 : 00000004  r0 : 9df76548
Flags: nzCv  IRQs off  FIQs off  Mode SVC_32
Code: 00000000 00000000 00000000 00000011 (79706f43) 
Resetting CPU ...resetting ...U-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 29C
Reset cause: POR
Model: i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment[*]-Video Link 0 (480 x 272)[0] lcdif@21c8000, video
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:   
Error: ethernet@20b4000 address not set.Error: ethernet@20b4000 address not set.Error: ethernet@20b4000 address not set.
FEC: can't find phy-handleError: ethernet@20b4000 address not set.
Could not get PHY for FEC0: addr 2Error: ethernet@20b4000 address not set.
FEC: can't find phy-handleError: ethernet@20b4000 address not set.
Could not get PHY for FEC0: addr 2
No ethernet found.Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0 
=> U-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 30C
Reset cause: POR
Model: i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment[*]-Video Link 0 (480 x 272)[0] lcdif@21c8000, video
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:   Could not get PHY for FEC1: addr 1
Could not get PHY for FEC1: addr 1
Get shared mii bus on ethernet@2188000
Could not get PHY for FEC1: addr 2
Get shared mii bus on ethernet@2188000
undefined instruction
pc : [<00000084>]          lr : [<9ef9a047>]
reloc pc : [<e888a084>]    lr : [<87824047>]
sp : 9df6b718  ip : 00000020     fp : 00000017
r10: 9df93400  r9 : 9df73ed0     r8 : 9df754b8
r7 : 9df75458  r6 : 00000006     r5 : 00000004  r4 : 9df76548
r3 : 00000048  r2 : 00000006     r1 : 00000004  r0 : 9df76548
Flags: nzCv  IRQs off  FIQs off  Mode SVC_32
Code: 00000000 00000000 00000000 00000011 (79706f43) 
Resetting CPU ...resetting ...U-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
Model: i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment[*]-Video Link 0 (480 x 272)[0] lcdif@21c8000, video
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:   
Error: ethernet@20b4000 address not set.Error: ethernet@20b4000 address not set.Error: ethernet@20b4000 address not set.
FEC: can't find phy-handleError: ethernet@20b4000 address not set.
Could not get PHY for FEC0: addr 2Error: ethernet@20b4000 address not set.
FEC: can't find phy-handleError: ethernet@20b4000 address not set.
Could not get PHY for FEC0: addr 2
No ethernet found.Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
9004056 bytes read in 426 ms (20.2 MiB/s)
Booting from mmc ...
35579 bytes read in 17 ms (2 MiB/s)
1056900 bytes read in 60 ms (16.8 MiB/s)
## Booting kernel from Legacy Image at 84000000 ...Image Name:   Image Type:   ARM Linux Kernel Image (uncompressed)Data Size:    1056836 Bytes = 1 MiBLoad Address: 84000000Entry Point:  84000000Verifying Checksum ... OK
## Flattened Device Tree blob at 83000000Booting using the fdt blob at 0x83000000Loading Kernel ImageUsing Device Tree in place at 83000000, end 8300bafa
Modify /soc/aips-bus@2200000/epdc@228c000:status disabled
ft_system_setup for mx6Starting kernel ...E/TC:0 0 plat_rng_init:188 Warning: seeding RNG with zeroes
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.47-2.2.0+g5ec03d06f54e (oe-user@oe-host) (gcc version 9.2.0 (GCC)) #1 SMP PREEMPT Wed Dec 9 10:05:01 UTC 2020
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Freescale i.MX6 ULL 14x14 EVK Board
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Reserved memory: created CMA memory pool at 0x96000000, size 160 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 15 pages/cpu s32076 r8192 d21172 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 121728
[    0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 302988K/491520K available (12288K kernel code, 576K rwdata, 4272K rodata, 1024K init, 433K bss, 24692K reserved, 163840K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x2c8/0x488 with crng_init=0
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000018] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000055] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.002973] Console: colour dummy device 80x30
[    0.003041] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.003077] pid_max: default: 32768 minimum: 301
[    0.003465] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.003502] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.005246] CPU: Testing write buffer coherency: ok
[    0.005979] CPU0: update cpu_capacity 1024
[    0.006012] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.060588] Setting up static identity map for 0x80100000 - 0x80100060
[    0.080565] rcu: Hierarchical SRCU implementation.
[    0.120735] smp: Bringing up secondary CPUs ...
[    0.120770] smp: Brought up 1 node, 1 CPU
[    0.120791] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[    0.120808] CPU: All CPU(s) started in SVC mode.
[    0.121701] devtmpfs: initialized
[    0.141231] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.142221] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.142273] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[    0.155572] pinctrl core: initialized pinctrl subsystem
[    0.158109] NET: Registered protocol family 16
[    0.178352] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.181084] cpuidle: using governor menu
[    0.199139] vdd3p0: supplied by regulator-dummy
[    0.200504] cpu: supplied by regulator-dummy
[    0.201992] vddsoc: supplied by regulator-dummy
[    0.226682] No ATAGs?
[    0.226822] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.226861] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.231229] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[    0.232031] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/aips-bus@2200000/iomuxc-snvs@2290000
[    0.232072] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[    0.234850] imx mu driver is registered.
[    0.235899] imx rpmsg driver is registered.
[    0.318494] vgaarb: loaded
[    0.320441] SCSI subsystem initialized
[    0.323271] usbcore: registered new interface driver usbfs
[    0.323407] usbcore: registered new interface driver hub
[    0.323650] usbcore: registered new device driver usb
[    0.326962] i2c i2c-0: IMX I2C adapter registered
[    0.329060] i2c i2c-1: IMX I2C adapter registered
[    0.329976] mc: Linux media interface: v0.10
[    0.330090] videodev: Linux video capture interface: v2.00
[    0.330224] pps_core: LinuxPPS API ver. 1 registered
[    0.330245] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.330298] PTP clock support registered
[    0.333641] MIPI CSI2 driver module loaded
[    0.333781] Advanced Linux Sound Architecture Driver Initialized.
[    0.335644] Bluetooth: Core ver 2.22
[    0.335781] NET: Registered protocol family 31
[    0.335803] Bluetooth: HCI device and connection manager initialized
[    0.335840] Bluetooth: HCI socket layer initialized
[    0.335867] Bluetooth: L2CAP socket layer initialized
[    0.335924] Bluetooth: SCO socket layer initialized
[    0.337093] clocksource: Switched to clocksource mxc_timer1
[    0.337528] VFS: Disk quotas dquot_6.6.0
[    0.337738] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.361128] thermal_sys: Registered thermal governor 'step_wise'
[    0.361779] NET: Registered protocol family 2
[    0.363169] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.363259] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.363375] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.363532] TCP: Hash tables configured (established 4096 bind 4096)
[    0.363751] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.363819] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.364232] NET: Registered protocol family 1
[    0.395794] RPC: Registered named UNIX socket transport module.
[    0.395829] RPC: Registered udp transport module.
[    0.395846] RPC: Registered tcp transport module.
[    0.395860] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.407376] PCI: CLS 0 bytes, default 64
[    0.408930] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.412641] Bus freq driver module loaded
[    0.415141] Initialise system trusted keyrings
[    0.415724] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.443510] NFS: Registering the id_resolver key type
[    0.443585] Key type id_resolver registered
[    0.443606] Key type id_legacy registered
[    0.443706] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.444971] fuse: init (API version 7.31)
[    0.535538] Key type asymmetric registered
[    0.535573] Asymmetric key parser 'x509' registered
[    0.535643] io scheduler mq-deadline registered
[    0.535663] io scheduler kyber registered
[    0.556266] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator
[    0.563816] mxsfb 21c8000.lcdif: 21c8000.lcdif supply lcd not found, using dummy regulator
[    0.674905] sii902x bound to mxs-lcdif from 21c8000.lcdif
[    0.679074] Console: switching to colour frame buffer device 60x34
[    0.776861] mxsfb 21c8000.lcdif: initialized
[    0.787034] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[    0.787227] imx-sdma 20ec000.sdma: Falling back to sysfs fallback for: imx/sdma/sdma-imx6q.bin
[    0.791732] mxs-dma 1804000.dma-apbh: initialized
[    0.799790] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX
[    1.541148] printk: console [ttymxc0] enabled
[    1.548009] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 67, base_baud = 5000000) is a IMX
[    1.592260] imx_rngc 2284000.rng: Freescale RNGC registered.
[    1.598763] imx sema4 driver is registered.
[    1.641523] brd: module loaded
[    1.665250] loop: module loaded
[    1.671449] imx ahci driver is registered.
[    1.683903] spi-nor spi4.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff
[    1.692374] gpio@0 enforce active low on chipselect handle
[    1.702858] libphy: Fixed MDIO Bus: probed
[    1.708522] CAN device driver interface
[    1.717499] pps pps0: new PPS source ptp0
[    1.723862] fec 20b4000.ethernet: Invalid MAC address: 00:00:00:00:00:00
[    1.730768] fec 20b4000.ethernet: Using random MAC address: e6:07:e1:c2:a3:3d
[    1.738858] libphy: fec_enet_mii_bus: probed
[    1.743468] mdio_bus 20b4000.ethernet-1: MDIO device at address 2 is missing.
[    1.764116] fec 20b4000.ethernet eth0: registered PHC device 0
[    1.773159] pps pps1: new PPS source ptp1
[    1.779888] fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
[    1.786676] fec 2188000.ethernet: Using random MAC address: 16:06:6e:4e:b9:e4
[    1.796139] fec 2188000.ethernet eth1: registered PHC device 1
[    1.803015] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.809055] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.816315] usbcore: registered new interface driver r8152
[    1.822178] usbcore: registered new interface driver lan78xx
[    1.828080] usbcore: registered new interface driver asix
[    1.833604] usbcore: registered new interface driver ax88179_178a
[    1.839881] usbcore: registered new interface driver cdc_ether
[    1.845889] usbcore: registered new interface driver smsc95xx
[    1.851817] usbcore: registered new interface driver net1080
[    1.857647] usbcore: registered new interface driver cdc_subset
[    1.863675] usbcore: registered new interface driver zaurus
[    1.869418] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    1.876979] usbcore: registered new interface driver cdc_ncm
[    1.882721] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.889426] ehci-pci: EHCI PCI platform driver
[    1.894018] ehci-mxc: Freescale On-Chip EHCI Host driver
[    1.900353] usbcore: registered new interface driver usb-storage
[    1.910937] imx_usb 2184000.usb: No over current polarity defined
[    1.917336] imx_usb 2184000.usb: 2184000.usb supply vbus not found, using dummy regulator
[    2.217523] random: fast init done
[    2.552577] mxs_phy 20c9000.usbphy: Data pin can't make good contact.
[    2.572144] imx_usb 2184200.usb: 2184200.usb supply vbus not found, using dummy regulator
[    2.585098] ci_hdrc ci_hdrc.1: EHCI Host Controller
[    2.590211] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[    2.627230] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[    2.633148] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[    2.641536] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.648837] usb usb1: Product: EHCI Host Controller
[    2.653752] usb usb1: Manufacturer: Linux 5.4.47-2.2.0+g5ec03d06f54e ehci_hcd
[    2.660959] usb usb1: SerialNumber: ci_hdrc.1
[    2.666866] hub 1-0:1.0: USB hub found
[    2.670935] hub 1-0:1.0: 1 port detected
[    2.690989] input: 20cc000.snvs:snvs-powerkey as /devices/soc0/soc/2000000.aips-bus/20cc000.snvs/20cc000.snvs:snvs-powerkey/input/input0
[    2.707388] input: iMX6UL Touchscreen Controller as /devices/soc0/soc/2000000.aips-bus/2040000.tsc/input/input1
[    2.721003] read sensor who am i (0x0)error !
[    2.725451] fxls8471: probe of 0-001e failed with error -22
[    2.736671] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc0
[    2.743298] i2c /dev entries driver
[    2.750824] pxp-v4l2 pxp_v4l2: initialized
[    2.756083] syscon-poweroff 20cc000.snvs:snvs-poweroff: pm_power_off already claimed (ptrval) psci_sys_poweroff
[    2.766377] syscon-poweroff: probe of 20cc000.snvs:snvs-poweroff failed with error -16
[    2.776443] mag3110 0-000e: 0-000e supply vdd not found, using dummy regulator
[    2.784288] mag3110 0-000e: 0-000e supply vddio not found, using dummy regulator
[    2.791981] mag3110 0-000e: check mag3110 chip ID
[    2.797175] mag3110 0-000e: read chip ID 0xfffffffa is not equal to 0xc4!
[    2.804298] mag3110: probe of 0-000e failed with error -22
[    2.813234] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[    2.820979] Bluetooth: HCI UART driver ver 2.3
[    2.825479] Bluetooth: HCI UART protocol H4 registered
[    2.830939] Bluetooth: HCI UART protocol BCSP registered
[    2.836424] Bluetooth: HCI UART protocol LL registered
[    2.841825] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    2.848248] Bluetooth: HCI UART protocol Marvell registered
[    2.853999] usbcore: registered new interface driver btusb
[    2.861459] sdhci: Secure Digital Host Controller Interface driver
[    2.867781] sdhci: Copyright(c) Pierre Ossman
[    2.872166] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.881026] sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO
[    2.931015] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[    3.002370] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
[    3.014034] caam-snvs 20cc000.caam-snvs: violation handlers armed - init state
[    3.028315] usbcore: registered new interface driver usbhid
[    3.033936] usbhid: USB HID core driver
[    3.038115] usb 1-1: new high-speed USB device number 2 using ci_hdrc
[    3.052418] optee: probing for conduit method from DT.
[    3.058136] optee: revision 3.10 (b3914e54)
[    3.058976] optee: dynamic shared memory is enabled
[    3.070301] optee: initialized driver
[    3.078408] mmc0: error -110 whilst initialising SD card
[    3.105637] fsl-sai 202c000.sai: failed to get mclk0 clock: -2
[    3.125022] debugfs: Directory '202c000.sai' with parent 'wm8960-audio' already present!
[    3.135465] imx-wm8960 sound-wm8960: wm8960-hifi <-> 202c000.sai mapping ok
[    3.151322] imx-wm8960 sound-wm8960: snd-soc-dummy-dai <-> 2034000.asrc mapping ok
[    3.161891] mmc1: new DDR MMC card at address 0001
[    3.167397] imx-wm8960 sound-wm8960: wm8960-hifi <-> 202c000.sai mapping ok
[    3.186096] mmcblk1: mmc1:0001 S40004 3.64 GiB 
[    3.192373] mmcblk1boot0: mmc1:0001 S40004 partition 1 4.00 MiB
[    3.199227] mmcblk1boot1: mmc1:0001 S40004 partition 2 4.00 MiB
[    3.205718] mmcblk1rpmb: mmc1:0001 S40004 partition 3 4.00 MiB, chardev (244:0)
[    3.229374]  mmcblk1: p1 p2 p3
[    3.237937] usb 1-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[    3.247776] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    3.260347] hub 1-1:1.0: USB hub found
[    3.264595] hub 1-1:1.0: 4 ports detected
[    3.305706] NET: Registered protocol family 26
[    3.311974] NET: Registered protocol family 10
[    3.329544] Segment Routing with IPv6
[    3.333468] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.341484] NET: Registered protocol family 17
[    3.346011] can: controller area network core (rev 20170425 abi 9)
[    3.352691] NET: Registered protocol family 29
[    3.357522] can: raw protocol (rev 20170425)
[    3.362227] can: broadcast manager protocol (rev 20170425 t)
[    3.368067] can: netlink gateway (rev 20190810) max_hops=1
[    3.374291] Bluetooth: RFCOMM TTY layer initialized
[    3.379926] Bluetooth: RFCOMM socket layer initialized
[    3.385373] Bluetooth: RFCOMM ver 1.11
[    3.389760] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    3.395410] Bluetooth: BNEP filters: protocol multicast
[    3.401015] Bluetooth: BNEP socket layer initialized
[    3.406227] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.412488] Bluetooth: HIDP socket layer initialized
[    3.417871] lib80211: common routines for IEEE802.11 drivers
[    3.423904] Key type dns_resolver registered
[    3.460597] Registering SWP/SWPB emulation handler
[    3.466661] Loading compiled-in X.509 certificates
[    3.504365] regulator-can-3v3 GPIO handle specifies active low - ignored
[    3.517882] imx_thermal tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C
[    3.528836] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:00:00 UTC (0)
[    3.538348] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    3.550030] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    3.556828] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    3.565912] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
[    3.574081] ALSA device list:
[    3.577198]   #0: wm8960-audio
[    3.580846] Waiting for root device /dev/mmcblk0p2...U-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 25C
Reset cause: POR
Model: i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment[*]-Video Link 0 (480 x 272)[0] lcdif@21c8000, video
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:   Could not get PHY for FEC1: addr 1
Could not get PHY for FEC1: addr 1
Get shared mii bus on ethernet@2188000
Could not get PHY for FEC1: addr 2
Get shared mii bus on ethernet@2188000
undefined instruction
pc : [<00000084>]          lr : [<9ef9a047>]
reloc pc : [<e888a084>]    lr : [<87824047>]
sp : 9df6b718  ip : 00000020     fp : 00000017
r10: 9df93400  r9 : 9df73ed0     r8 : 9df754b8
r7 : 9df75458  r6 : 00000006     r5 : 00000004  r4 : 9df76548
r3 : 00000048  r2 : 00000006     r1 : 00000004  r0 : 9df76548
Flags: nzCv  IRQs off  FIQs off  Mode SVC_32
Code: 00000000 00000000 00000000 00000011 (79706f43) 
Resetting CPU ...resetting ...U-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 26C
Reset cause: POR
Model: i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment[*]-Video Link 0 (480 x 272)[0] lcdif@21c8000, video
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:   
Error: ethernet@20b4000 address not set.Error: ethernet@20b4000 address not set.Error: ethernet@20b4000 address not set.
FEC: can't find phy-handleError: ethernet@20b4000 address not set.
Could not get PHY for FEC0: addr 2Error: ethernet@20b4000 address not set.
FEC: can't find phy-handleError: ethernet@20b4000 address not set.
Could not get PHY for FEC0: addr 2
No ethernet found.Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
9004056 bytes read in 432 ms (19.9 MiB/s)
Booting from mmc ...
35579 bytes read in 17 ms (2 MiB/s)
1056900 bytes read in 60 ms (16.8 MiB/s)
## Booting kernel from Legacy Image at 84000000 ...Image Name:   Image Type:   ARM Linux Kernel Image (uncompressed)Data Size:    1056836 Bytes = 1 MiBLoad Address: 84000000Entry Point:  84000000Verifying Checksum ... OK
## Flattened Device Tree blob at 83000000Booting using the fdt blob at 0x83000000Loading Kernel ImageUsing Device Tree in place at 83000000, end 8300bafa
Modify /soc/aips-bus@2200000/epdc@228c000:status disabled
ft_system_setup for mx6Starting kernel ...E/TC:0 0 plat_rng_init:188 Warning: seeding RNG with zeroes
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.47-2.2.0+g5ec03d06f54e (oe-user@oe-host) (gcc version 9.2.0 (GCC)) #1 SMP PREEMPT Wed Dec 9 10:05:01 UTC 2020
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Freescale i.MX6 ULL 14x14 EVK Board
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Reserved memory: created CMA memory pool at 0x96000000, size 160 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedd[   22.222739] random: crng init done
[   33.767231] VSD_3V3: disabling
[   33.770351] can-3v3: disablingU-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 29C
Reset cause: POR
Model: i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment[*]-Video Link 0 (480 x 272)[0] lcdif@21c8000, video
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:   Could not get PHY for FEC1: addr 1
Could not get PHY for FEC1: addr 1
Get shared mii bus on ethernet@2188000
Could not get PHY for FEC1: addr 2
Get shared mii bus on ethernet@2188000
undefined instruction
pc : [<00000084>]          lr : [<9ef9a047>]
reloc pc : [<e888a084>]    lr : [<87824047>]
sp : 9df6b718  ip : 00000020     fp : 00000017
r10: 9df93400  r9 : 9df73ed0     r8 : 9df754b8
r7 : 9df75458  r6 : 00000006     r5 : 00000004  r4 : 9df76548
r3 : 00000048  r2 : 00000006     r1 : 00000004  r0 : 9df76548
Flags: nzCv  IRQs off  FIQs off  Mode SVC_32
Code: 00000000 00000000 00000000 00000011 (79706f43) 
Resetting CPU ...resetting ...U-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
Model: i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment[*]-Video Link 0 (480 x 272)[0] lcdif@21c8000, video
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:   
Error: ethernet@20b4000 address not set.Error: ethernet@20b4000 address not set.Error: ethernet@20b4000 address not set.
FEC: can't find phy-handleError: ethernet@20b4000 address not set.
Could not get PHY for FEC0: addr 2Error: ethernet@20b4000 address not set.
FEC: can't find phy-handleError: ethernet@20b4000 address not set.
Could not get PHY for FEC0: addr 2
No ethernet found.Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0 
=> U-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
Model: i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment[*]-Video Link 0 (480 x 272)[0] lcdif@21c8000, video
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:   Could not get PHY for FEC1: addr 1
Could not get PHY for FEC1: addr 1
Get shared mii bus on ethernet@2188000
Could not get PHY for FEC1: addr 2
Get shared mii bus on ethernet@2188000
undefined instruction
pc : [<00000084>]          lr : [<9ef9a047>]
reloc pc : [<e888a084>]    lr : [<87824047>]
sp : 9df6b718  ip : 00000020     fp : 00000017
r10: 9df93400  r9 : 9df73ed0     r8 : 9df754b8
r7 : 9df75458  r6 : 00000006     r5 : 00000004  r4 : 9df76548
r3 : 00000048  r2 : 00000006     r1 : 00000004  r0 : 9df76548
Flags: nzCv  IRQs off  FIQs off  Mode SVC_32
Code: 00000000 00000000 00000000 00000011 (79706f43) 
Resetting CPU ...resetting ...U-Boot 2020.04-5.4.47-2.2.0+gffc3fbe7e5 (Dec 09 2020 - 10:22:59 +0000)CPU:   i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
Model: i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment[*]-Video Link 0 (480 x 272)[0] lcdif@21c8000, video
In:    serial
Out:   serial
Err:   serial
switch to partitions #0, OK
mmc0 is current device
flash target is MMC:0
Net:   
Error: ethernet@20b4000 address not set.Error: ethernet@20b4000 address not set.Error: ethernet@20b4000 address not set.
FEC: can't find phy-handleError: ethernet@20b4000 address not set.
Could not get PHY for FEC0: addr 2Error: ethernet@20b4000 address not set.
FEC: can't find phy-handleError: ethernet@20b4000 address not set.
Could not get PHY for FEC0: addr 2
No ethernet found.Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
9004056 bytes read in 428 ms (20.1 MiB/s)
Booting from mmc ...
35579 bytes read in 17 ms (2 MiB/s)
1056900 bytes read in 60 ms (16.8 MiB/s)
## Booting kernel from Legacy Image at 84000000 ...Image Name:   Image Type:   ARM Linux Kernel Image (uncompressed)Data Size:    1056836 Bytes = 1 MiBLoad Address: 84000000Entry Point:  84000000Verifying Checksum ... OK
## Flattened Device Tree blob at 83000000Booting using the fdt blob at 0x83000000Loading Kernel ImageUsing Device Tree in place at 83000000, end 8300bafa
Modify /soc/aips-bus@2200000/epdc@228c000:status disabled
ft_system_setup for mx6Starting kernel ...E/TC:0 0 plat_rng_init:188 Warning: seeding RNG with zeroes
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.47-2.2.0+g5ec03d06f54e (oe-user@oe-host) (gcc version 9.2.0 (GCC)) #1 SMP PREEMPT Wed Dec 9 10:05:01 UTC 2020
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Freescale i.MX6 ULL 14x14 EVK Board
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Reserved memory: created CMA memory pool at 0x96000000, size 160 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 15 pages/cpu s32076 r8192 d21172 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 121728
[    0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 302988K/491520K available (12288K kernel code, 576K rwdata, 4272K rodata, 1024K init, 433K bss, 24692K reserved, 163840K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x2c8/0x488 with crng_init=0
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000016] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000055] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.002962] Console: colour dummy device 80x30
[    0.003032] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.003067] pid_max: default: 32768 minimum: 301
[    0.003456] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.003493] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.005236] CPU: Testing write buffer coherency: ok
[    0.005976] CPU0: update cpu_capacity 1024
[    0.006011] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.060586] Setting up static identity map for 0x80100000 - 0x80100060
[    0.080571] rcu: Hierarchical SRCU implementation.
[    0.120741] smp: Bringing up secondary CPUs ...
[    0.120776] smp: Brought up 1 node, 1 CPU
[    0.120798] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[    0.120814] CPU: All CPU(s) started in SVC mode.
[    0.121714] devtmpfs: initialized
[    0.141236] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.142226] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.142280] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[    0.155562] pinctrl core: initialized pinctrl subsystem
[    0.158087] NET: Registered protocol family 16
[    0.178287] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.181006] cpuidle: using governor menu
[    0.198978] vdd3p0: supplied by regulator-dummy
[    0.200355] cpu: supplied by regulator-dummy
[    0.201847] vddsoc: supplied by regulator-dummy
[    0.226577] No ATAGs?
[    0.226720] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.226757] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.231138] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[    0.231945] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined in /soc/aips-bus@2200000/iomuxc-snvs@2290000
[    0.231983] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[    0.234771] imx mu driver is registered.
[    0.235826] imx rpmsg driver is registered.
[    0.318522] vgaarb: loaded
[    0.320475] SCSI subsystem initialized
[    0.323289] usbcore: registered new interface driver usbfs
[    0.323427] usbcore: registered new interface driver hub
[    0.323676] usbcore: registered new device driver usb
[    0.327020] i2c i2c-0: IMX I2C adapter registered
[    0.329127] i2c i2c-1: IMX I2C adapter registered
[    0.330043] mc: Linux media interface: v0.10
[    0.330153] videodev: Linux video capture interface: v2.00
[    0.330291] pps_core: LinuxPPS API ver. 1 registered
[    0.330312] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.330366] PTP clock support registered
[    0.333700] MIPI CSI2 driver module loaded
[    0.333836] Advanced Linux Sound Architecture Driver Initialized.
[    0.335689] Bluetooth: Core ver 2.22
[    0.335826] NET: Registered protocol family 31
[    0.335846] Bluetooth: HCI device and connection manager initialized
[    0.335884] Bluetooth: HCI socket layer initialized
[    0.335911] Bluetooth: L2CAP socket layer initialized
[    0.335968] Bluetooth: SCO socket layer initialized
[    0.337141] clocksource: Switched to clocksource mxc_timer1
[    0.337581] VFS: Disk quotas dquot_6.6.0
[    0.337791] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.361266] thermal_sys: Registered thermal governor 'step_wise'
[    0.361929] NET: Registered protocol family 2
[    0.363324] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.363412] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.363525] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.363682] TCP: Hash tables configured (established 4096 bind 4096)
[    0.363901] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.363970] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.364386] NET: Registered protocol family 1
[    0.395959] RPC: Registered named UNIX socket transport module.
[    0.395994] RPC: Registered udp transport module.
[    0.396011] RPC: Registered tcp transport module.
[    0.396027] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.407558] PCI: CLS 0 bytes, default 64
[    0.409114] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.412836] Bus freq driver module loaded
[    0.415330] Initialise system trusted keyrings
[    0.415905] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.443714] NFS: Registering the id_resolver key type
[    0.443805] Key type id_resolver registered
[    0.443827] Key type id_legacy registered
[    0.443930] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.445196] fuse: init (API version 7.31)
[    0.533511] Key type asymmetric registered
[    0.533545] Asymmetric key parser 'x509' registered
[    0.533613] io scheduler mq-deadline registered
[    0.533633] io scheduler kyber registered
[    0.554352] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator
[    0.562864] mxsfb 21c8000.lcdif: 21c8000.lcdif supply lcd not found, using dummy regulator
[    0.673949] sii902x bound to mxs-lcdif from 21c8000.lcdif
[    0.678124] Console: switching to colour frame buffer device 60x34
[    0.776047] mxsfb 21c8000.lcdif: initialized
[    0.786324] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[    0.786364] imx-sdma 20ec000.sdma: Falling back to sysfs fallback for: imx/sdma/sdma-imx6q.bin
[    0.791087] mxs-dma 1804000.dma-apbh: initialized
[    0.799103] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 21, base_baud = 5000000) is a IMX
[    1.540479] printk: console [ttymxc0] enabled
[    1.547353] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 67, base_baud = 5000000) is a IMX
[    1.591629] imx_rngc 2284000.rng: Freescale RNGC registered.
[    1.598136] imx sema4 driver is registered.
[    1.640945] brd: module loaded
[    1.664631] loop: module loaded
[    1.670830] imx ahci driver is registered.
[    1.683325] spi-nor spi4.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff
[    1.691817] gpio@0 enforce active low on chipselect handle
[    1.702302] libphy: Fixed MDIO Bus: probed
[    1.707983] CAN device driver interface
[    1.716772] pps pps0: new PPS source ptp0
[    1.723378] fec 20b4000.ethernet: Invalid MAC address: 00:00:00:00:00:00
[    1.730282] fec 20b4000.ethernet: Using random MAC address: 3a:fd:ed:5f:ac:ce
[    1.738367] libphy: fec_enet_mii_bus: probed
[    1.742979] mdio_bus 20b4000.ethernet-1: MDIO device at address 2 is missing.
[    1.763643] fec 20b4000.ethernet eth0: registered PHC device 0
[    1.772694] pps pps1: new PPS source ptp1
[    1.779401] fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
[    1.786191] fec 2188000.ethernet: Using random MAC address: c6:8c:7f:61:b9:5b
[    1.795663] fec 2188000.ethernet eth1: registered PHC device 1
[    1.802536] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.808573] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.815845] usbcore: registered new interface driver r8152
[    1.821711] usbcore: registered new interface driver lan78xx
[    1.827611] usbcore: registered new interface driver asix
[    1.833134] usbcore: registered new interface driver ax88179_178a
[    1.839412] usbcore: registered new interface driver cdc_ether
[    1.845419] usbcore: registered new interface driver smsc95xx
[    1.851346] usbcore: registered new interface driver net1080
[    1.857181] usbcore: registered new interface driver cdc_subset
[    1.863216] usbcore: registered new interface driver zaurus
[    1.868958] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    1.876523] usbcore: registered new interface driver cdc_ncm
[    1.882266] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.888967] ehci-pci: EHCI PCI platform driver
[    1.893561] ehci-mxc: Freescale On-Chip EHCI Host driver
[    1.899893] usbcore: registered new interface driver usb-storage
[    1.910481] imx_usb 2184000.usb: No over current polarity defined
[    1.916758] imx_usb 2184000.usb: 2184000.usb supply vbus not found, using dummy regulator
[    2.205075] random: fast init done
[    2.552651] mxs_phy 20c9000.usbphy: Data pin can't make good contact.
[    2.572237] imx_usb 2184200.usb: 2184200.usb supply vbus not found, using dummy regulator
[    2.585212] ci_hdrc ci_hdrc.1: EHCI Host Controller
[    2.590315] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[    2.627283] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[    2.633209] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[    2.641590] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.648897] usb usb1: Product: EHCI Host Controller
[    2.653810] usb usb1: Manufacturer: Linux 5.4.47-2.2.0+g5ec03d06f54e ehci_hcd
[    2.661017] usb usb1: SerialNumber: ci_hdrc.1
[    2.666936] hub 1-0:1.0: USB hub found
[    2.671009] hub 1-0:1.0: 1 port detected
[    2.691070] input: 20cc000.snvs:snvs-powerkey as /devices/soc0/soc/2000000.aips-bus/20cc000.snvs/20cc000.snvs:snvs-powerkey/input/input0
[    2.707500] input: iMX6UL Touchscreen Controller as /devices/soc0/soc/2000000.aips-bus/2040000.tsc/input/input1
[    2.721138] read sensor who am i (0x0)error !
[    2.725589] fxls8471: probe of 0-001e failed with error -22
[    2.736770] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc0
[    2.743398] i2c /dev entries driver
[    2.750942] pxp-v4l2 pxp_v4l2: initialized
[    2.756205] syscon-poweroff 20cc000.snvs:snvs-poweroff: pm_power_off already claimed (ptrval) psci_sys_poweroff
[    2.766500] syscon-poweroff: probe of 20cc000.snvs:snvs-poweroff failed with error -16
[    2.776581] mag3110 0-000e: 0-000e supply vdd not found, using dummy regulator
[    2.784435] mag3110 0-000e: 0-000e supply vddio not found, using dummy regulator
[    2.792137] mag3110 0-000e: check mag3110 chip ID
[    2.797347] mag3110 0-000e: read chip ID 0xfffffffa is not equal to 0xc4!
[    2.804473] mag3110: probe of 0-000e failed with error -22
[    2.813442] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[    2.821190] Bluetooth: HCI UART driver ver 2.3
[    2.825689] Bluetooth: HCI UART protocol H4 registered
[    2.831151] Bluetooth: HCI UART protocol BCSP registered
[    2.836639] Bluetooth: HCI UART protocol LL registered
[    2.842038] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    2.848465] Bluetooth: HCI UART protocol Marvell registered
[    2.854219] usbcore: registered new interface driver btusb
[    2.861694] sdhci: Secure Digital Host Controller Interface driver
[    2.868018] sdhci: Copyright(c) Pierre Ossman
[    2.872402] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.881234] sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO
[    2.941684] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[    3.002774] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
[    3.014460] caam-snvs 20cc000.caam-snvs: violation handlers armed - init state
[    3.028718] usbcore: registered new interface driver usbhid
[    3.034341] usbhid: USB HID core driver
[    3.038526] usb 1-1: new high-speed USB device number 2 using ci_hdrc
[    3.052794] optee: probing for conduit method from DT.
[    3.058507] optee: revision 3.10 (b3914e54)
[    3.059366] optee: dynamic shared memory is enabled
[    3.070696] optee: initialized driver
[    3.078573] mmc0: error -110 whilst initialising SD card
[    3.106052] fsl-sai 202c000.sai: failed to get mclk0 clock: -2
[    3.125465] debugfs: Directory '202c000.sai' with parent 'wm8960-audio' already present!
[    3.135897] imx-wm8960 sound-wm8960: wm8960-hifi <-> 202c000.sai mapping ok
[    3.150012] imx-wm8960 sound-wm8960: snd-soc-dummy-dai <-> 2034000.asrc mapping ok
[    3.158350] imx-wm8960 sound-wm8960: wm8960-hifi <-> 202c000.sai mapping ok
[    3.170223] mmc1: new DDR MMC card at address 0001
[    3.188139] mmcblk1: mmc1:0001 S40004 3.64 GiB 
[    3.193339] mmcblk1boot0: mmc1:0001 S40004 partition 1 4.00 MiB
[    3.200172] mmcblk1boot1: mmc1:0001 S40004 partition 2 4.00 MiB
[    3.206708] mmcblk1rpmb: mmc1:0001 S40004 partition 3 4.00 MiB, chardev (244:0)
[    3.230329]  mmcblk1: p1 p2 p3
[    3.238054] usb 1-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[    3.246336] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    3.261430] hub 1-1:1.0: USB hub found
[    3.265833] hub 1-1:1.0: 4 ports detected
[    3.305773] NET: Registered protocol family 26
[    3.312061] NET: Registered protocol family 10
[    3.329631] Segment Routing with IPv6
[    3.333552] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.341596] NET: Registered protocol family 17
[    3.346120] can: controller area network core (rev 20170425 abi 9)
[    3.352797] NET: Registered protocol family 29
[    3.357642] can: raw protocol (rev 20170425)
[    3.362329] can: broadcast manager protocol (rev 20170425 t)
[    3.368169] can: netlink gateway (rev 20190810) max_hops=1
[    3.374393] Bluetooth: RFCOMM TTY layer initialized
[    3.380032] Bluetooth: RFCOMM socket layer initialized
[    3.385663] Bluetooth: RFCOMM ver 1.11
[    3.389920] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    3.395501] Bluetooth: BNEP filters: protocol multicast
[    3.401137] Bluetooth: BNEP socket layer initialized
[    3.406342] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.412585] Bluetooth: HIDP socket layer initialized
[    3.417965] lib80211: common routines for IEEE802.11 drivers
[    3.423984] Key type dns_resolver registered
[    3.460676] Registering SWP/SWPB emulation handler
[    3.466738] Loading compiled-in X.509 certificates
[    3.504413] regulator-can-3v3 GPIO handle specifies active low - ignored
[    3.517904] imx_thermal tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C
[    3.528852] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:00:00 UTC (0)
[    3.538356] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    3.550058] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    3.556852] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    3.565932] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
[    3.574108] ALSA device list:
[    3.577228]   #0: wm8960-audio
[    3.580876] Waiting for root device /dev/mmcblk0p2...
[   33.767284] VSD_3V3: disabling
[   33.770410] can-3v3: disabling
[   64.487708] cfg80211: failed to load regulatory.db
[   64.493556] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[   64.503406] imx-sdma 20ec000.sdma: Falling back to sysfs fallback for: imx/sdma/sdma-imx6q.bin
[  125.927710] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[  203.287395] random: crng init done