【STM32CubeIDE】软件硬件SPI+六针OLED使用

前言

本文将介绍STM32 + 6针OLED的使用，分别使用软件和硬件两种SPI驱动方式，最终实现OLED显示TEST-ok字符和数字累加刷新显示

软件平台：STM32CubeIDE+HAL库

硬件：STM32F103ZET6(正点原子战舰V3)+六针OLED

题外话：

最近在学习STM32CubeIDE+HAL库，想做几个小模块练练手，结果遇到各种奇怪的异常，反复排查自己代码都不觉得问题，最后发现接触不良的原因，害。所以大家在写软件之前一定要确保自己硬件是ok的，遇到问题不要光埋头在软件里找原因，血泪的教训T.T

目录

    • 前言
    • 六针OLED简介
    • 软件SPI配置
      • 1.创建新工程
      • 2.设置引脚
      • 3.添加驱动文件
      • 4.初始化驱动
      • 5.编译烧录
    • 软件SPI接线
    • 硬件SPI配置
    • 硬件SPI启动DMA
    • 硬件SPI接线
    • 工程源码
    • 参考链接

六针OLED简介

OLED工作机制和原理网上有很多资料，这里不过多赘述了

市面上常见的OLED0.96寸显示屏有4针、6针，7针三种。其中，7针屏幕CS端接地就是6针屏幕。

4针通常是使用IIC驱动，VCC、GND、SCL、SDA四脚即可；而6针、7针通常是用于SPI驱动（有些通过修改硬件也可以换成IIC驱动）

以下是6针/7针OLED引脚定义

引脚定义
GND接地端口
VCC电源端口，接3.3V电源端口
D0CLK时钟信号端口（SCL）
D1数据端口（SDA）
RES复位端口（RST）
D/C数据/命令选择引脚
CS片选引脚(低电平有效，悬空也可使用)，6针默认已经接地，没有引出

软件SPI配置

1.创建新工程

image-20240522221917502

在此处搜索对应的芯片型号

image-20240505221008688

在右边选择要使用的芯片型号，按next下一步

常用的芯片型号可以加星，下次可以在搜索上边的星星里直接找到

image-20240505221119292

设置新建项目的名称，直接按Finish即可新建项目

next里边有一些设置，根据需要去更改，一般保持默认即可
image-20240505221322266

2.设置引脚

确定除电源和GND外，SPI协议要用的4个引脚，SCL、SDA、RES、DC,这里使用PC0/PC1/PC2/PC3

将4个引脚的GPIO mode都设置成Output Push Pull（推挽输出）

并设置对应的User Label（主要是为了生成宏兼容驱动，不改后边代码里自己定义宏也行）

image-20240522222358501

#define OLED_RS_Pin GPIO_PIN_0
#define OLED_RS_GPIO_Port GPIOC
#define OLED_SCLK_Pin GPIO_PIN_1
#define OLED_SCLK_GPIO_Port GPIOC
#define OLED_SDIN_Pin GPIO_PIN_2
#define OLED_SDIN_GPIO_Port GPIOC
#define OLED_RST_Pin GPIO_PIN_3
#define OLED_RST_GPIO_Port GPIOC

3.添加驱动文件

驱动文件一般厂家都会提供，网上购买的可以联系客服要。以下驱动文件可用于0.96寸6针OLED

在对应文件夹下添加oled.h、oled.c和oledfont.h文件，可以新建文件然后复制进来。用其他方法添加到工程也行，这里不过多赘述。
image-20240522223333027

oled.h

#ifndef OLED_H_
#define OLED_H_#include "main.h"#define u8 uint8_t
#define u16 uint16_t
#define u32 uint32_t
//-----------------OLED端口定义----------------
#define OLED_RST_Clr() HAL_GPIO_WritePin(OLED_RST_GPIO_Port, OLED_RST_Pin, GPIO_PIN_RESET)   //RST
#define OLED_RST_Set() HAL_GPIO_WritePin(OLED_RST_GPIO_Port, OLED_RST_Pin, GPIO_PIN_SET)   //RST#define OLED_RS_Clr() HAL_GPIO_WritePin(OLED_RS_GPIO_Port, OLED_RS_Pin, GPIO_PIN_RESET)    //DC
#define OLED_RS_Set() HAL_GPIO_WritePin(OLED_RS_GPIO_Port, OLED_RS_Pin, GPIO_PIN_SET)    //DC#define OLED_SCLK_Clr()  HAL_GPIO_WritePin(OLED_SCLK_GPIO_Port, OLED_SCLK_Pin, GPIO_PIN_RESET)  //SCL
#define OLED_SCLK_Set()  HAL_GPIO_WritePin(OLED_SCLK_GPIO_Port, OLED_SCLK_Pin, GPIO_PIN_SET)  //SCL#define OLED_SDIN_Clr()  HAL_GPIO_WritePin(OLED_SDIN_GPIO_Port, OLED_SDIN_Pin, GPIO_PIN_RESET)   //SDA
#define OLED_SDIN_Set()  HAL_GPIO_WritePin(OLED_SDIN_GPIO_Port, OLED_SDIN_Pin, GPIO_PIN_SET)   //SDA#define OLED_CMD  0	//写命令
#define OLED_DATA 1	//写数据
//OLED控制用函数
void OLED_WR_Byte(u8 dat,u8 cmd);
void OLED_Display_On(void);
void OLED_Display_Off(void);
void OLED_Refresh_Gram(void);
void OLED_Init(void);
void OLED_Clear(void);
void OLED_DrawPoint(u8 x,u8 y,u8 t);
void OLED_ShowChar(u8 x,u8 y,u8 chr,u8 size,u8 mode);
void OLED_ShowNumber(u8 x,u8 y,u32 num,u8 len,u8 size);
void OLED_ShowString(u8 x,u8 y,const u8 *p);
void OLED_ShowFloatNum(u8 x,u8 y,float num,u8 size1);
void OLED_ShowFloat(float value, uint8_t decimalPlaces, uint8_t x, uint8_t y);
void OLED_ShowFNum(u8 x,u8 y,float num,u8 len,u8 size,u8 mode);#endif /* OLED_H_ */

oled.c

#include <oled.h>
#include "stdlib.h"
#include "oledfont.h"u8 OLED_GRAM[128][8];void OLED_Refresh_Gram(void)
{u8 i,n;for(i=0;i<8;i++){OLED_WR_Byte (0xb0+i,OLED_CMD);    //设置页地址（0~7）OLED_WR_Byte (0x00,OLED_CMD);      //设置显示位置—列低地址OLED_WR_Byte (0x10,OLED_CMD);      //设置显示位置—列高地址for(n=0;n<128;n++)OLED_WR_Byte(OLED_GRAM[n][i],OLED_DATA);}
}//向OLED写入一个字节。
//dat:要写入的数据/命令
//cmd:数据/命令标志 0,表示命令;1,表示数据;
void OLED_WR_Byte(u8 dat,u8 cmd)
{u8 i;if(cmd)OLED_RS_Set();elseOLED_RS_Clr();for(i=0;i<8;i++){OLED_SCLK_Clr();if(dat&0x80)OLED_SDIN_Set();elseOLED_SDIN_Clr();OLED_SCLK_Set();dat<<=1;}OLED_RS_Set();
}//开启OLED显示
void OLED_Display_On(void)
{OLED_WR_Byte(0X8D,OLED_CMD);  //SET DCDC命令OLED_WR_Byte(0X14,OLED_CMD);  //DCDC ONOLED_WR_Byte(0XAF,OLED_CMD);  //DISPLAY ON
}
//关闭OLED显示
void OLED_Display_Off(void)
{OLED_WR_Byte(0X8D,OLED_CMD);  //SET DCDC命令OLED_WR_Byte(0X10,OLED_CMD);  //DCDC OFFOLED_WR_Byte(0XAE,OLED_CMD);  //DISPLAY OFF
}
//清屏函数,清完屏,整个屏幕是黑色的!和没点亮一样!!!
void OLED_Clear(void)
{u8 i,n;for(i=0;i<8;i++)for(n=0;n<128;n++)OLED_GRAM[n][i]=0X00;OLED_Refresh_Gram();//更新显示
}
//画点
//x:0~127
//y:0~63
//t:1 填充 0,清空
void OLED_DrawPoint(u8 x,u8 y,u8 t)
{u8 pos,bx,temp=0;if(x>127||y>63)return;//超出范围了.pos=7-y/8;bx=y%8;temp=1<<(7-bx);if(t)OLED_GRAM[x][pos]|=temp;else OLED_GRAM[x][pos]&=~temp;
}//在指定位置显示一个字符,包括部分字符
//x:0~127
//y:0~63
//mode:0,反白显示;1,正常显示
//size:选择字体 16/12
void OLED_ShowChar(u8 x,u8 y,u8 chr,u8 size,u8 mode)
{u8 temp,t,t1;u8 y0=y;chr=chr-' ';//得到偏移后的值for(t=0;t<size;t++){if(size==12)temp=oled_asc2_1206[chr][t];  //调用1206字体else temp=oled_asc2_1608[chr][t];		 //调用1608字体for(t1=0;t1<8;t1++){if(temp&0x80)OLED_DrawPoint(x,y,mode);else OLED_DrawPoint(x,y,!mode);temp<<=1;y++;if((y-y0)==size){y=y0;x++;break;}}}
}//m^n函数
u32 oled_pow(u8 m,u8 n)
{u32 result=1;while(n--)result*=m;return result;
}//显示2个数字
//x,y :起点坐标
//len :数字的位数
//size:字体大小
//mode:模式	0,填充模式;1,叠加模式
//num:数值(0~4294967295);
void OLED_ShowNumber(u8 x,u8 y,u32 num,u8 len,u8 size)
{u8 t,temp;u8 enshow=0;for(t=0;t<len;t++){temp=(num/oled_pow(10,len-t-1))%10;if(enshow==0&&t<(len-1)){if(temp==0){OLED_ShowChar(x+(size/2)*t,y,' ',size,1);continue;}else enshow=1;}OLED_ShowChar(x+(size/2)*t,y,temp+'0',size,1);}
}//显示字符串
//x,y:起点坐标
//*p:字符串起始地址
//用16字体
void OLED_ShowString(u8 x,u8 y,const u8 *p)
{
#define MAX_CHAR_POSX 122
#define MAX_CHAR_POSY 58while(*p!='\0'){if(x>MAX_CHAR_POSX){x=0;y+=16;}if(y>MAX_CHAR_POSY){y=x=0;OLED_Clear();}OLED_ShowChar(x,y,*p,12,1);x+=8;p++;}
}//显示浮点数字
//x,y :起点坐标
//value :要显示的值
//decimalPlaces，小数点后位数，
// 显示浮点数函数
void OLED_ShowFloat(float value, uint8_t decimalPlaces, uint8_t x, uint8_t y)
{char buffer[16];// 将浮点数转换为字符串格式，并指定小数位数snprintf(buffer, sizeof(buffer), "%.*f", decimalPlaces, value);// 在指定位置显示字符串for (uint8_t i = 0; i < strlen(buffer); i++){OLED_ShowChar(x + i * 8, y, buffer[i], 16, 1);}
}//初始化OLED
void OLED_Init(void)
{OLED_RST_Clr();HAL_Delay(100);OLED_RST_Set();OLED_WR_Byte(0xAE,OLED_CMD); //关闭显示OLED_WR_Byte(0xD5,OLED_CMD); //设置时钟分频因子,震荡频率OLED_WR_Byte(80,OLED_CMD);   //[3:0],分频因子;[7:4],震荡频率OLED_WR_Byte(0xA8,OLED_CMD); //设置驱动路数OLED_WR_Byte(0X3F,OLED_CMD); //默认0X3F(1/64)OLED_WR_Byte(0xD3,OLED_CMD); //设置显示偏移OLED_WR_Byte(0X00,OLED_CMD); //默认为0OLED_WR_Byte(0x40,OLED_CMD); //设置显示开始行 [5:0],行数.OLED_WR_Byte(0x8D,OLED_CMD); //电荷泵设置OLED_WR_Byte(0x14,OLED_CMD); //bit2，开启/关闭OLED_WR_Byte(0x20,OLED_CMD); //设置内存地址模式OLED_WR_Byte(0x02,OLED_CMD); //[1:0],00，列地址模式;01，行地址模式;10,页地址模式;默认10;OLED_WR_Byte(0xA1,OLED_CMD); //段重定义设置,bit0:0,0->0;1,0->127;OLED_WR_Byte(0xC0,OLED_CMD); //设置COM扫描方向;bit3:0,普通模式;1,重定义模式 COM[N-1]->COM0;N:驱动路数OLED_WR_Byte(0xDA,OLED_CMD); //设置COM硬件引脚配置OLED_WR_Byte(0x12,OLED_CMD); //[5:4]配置OLED_WR_Byte(0x81,OLED_CMD); //对比度设置OLED_WR_Byte(0xEF,OLED_CMD); //1~255;默认0X7F (亮度设置,越大越亮)OLED_WR_Byte(0xD9,OLED_CMD); //设置预充电周期OLED_WR_Byte(0xf1,OLED_CMD); //[3:0],PHASE 1;[7:4],PHASE 2;OLED_WR_Byte(0xDB,OLED_CMD); //设置VCOMH 电压倍率OLED_WR_Byte(0x30,OLED_CMD); //[6:4] 000,0.65*vcc;001,0.77*vcc;011,0.83*vcc;OLED_WR_Byte(0xA4,OLED_CMD); //全局显示开启;bit0:1,开启;0,关闭;(白屏/黑屏)OLED_WR_Byte(0xA6,OLED_CMD); //设置显示方式;bit0:1,反相显示;0,正常显示OLED_WR_Byte(0xAF,OLED_CMD); //开启显示OLED_Clear();
}
/** OLED.c**  Created on: May 22, 2024*      Author: 30985*/

oledfont.h

#ifndef OLEDFONT_H_
#define OLEDFONT_H_//常用ASCII表
//偏移量32
//ASCII字符集
//偏移量32
//大小:12*6
const unsigned char oled_asc2_1206[95][12]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x3F,0x40,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x30,0x00,0x40,0x00,0x30,0x00,0x40,0x00,0x00,0x00},/*""",2*/
{0x09,0x00,0x0B,0xC0,0x3D,0x00,0x0B,0xC0,0x3D,0x00,0x09,0x00},/*"#",3*/
{0x18,0xC0,0x24,0x40,0x7F,0xE0,0x22,0x40,0x31,0x80,0x00,0x00},/*"$",4*/
{0x18,0x00,0x24,0xC0,0x1B,0x00,0x0D,0x80,0x32,0x40,0x01,0x80},/*"%",5*/
{0x03,0x80,0x1C,0x40,0x27,0x40,0x1C,0x80,0x07,0x40,0x00,0x40},/*"&",6*/
{0x10,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x80,0x20,0x40,0x40,0x20},/*"(",8*/
{0x00,0x00,0x40,0x20,0x20,0x40,0x1F,0x80,0x00,0x00,0x00,0x00},/*")",9*/
{0x09,0x00,0x06,0x00,0x1F,0x80,0x06,0x00,0x09,0x00,0x00,0x00},/*"*",10*/
{0x04,0x00,0x04,0x00,0x3F,0x80,0x04,0x00,0x04,0x00,0x00,0x00},/*"+",11*/
{0x00,0x10,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x20,0x01,0xC0,0x06,0x00,0x38,0x00,0x40,0x00,0x00,0x00},/*"/",15*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"0",16*/
{0x00,0x00,0x10,0x40,0x3F,0xC0,0x00,0x40,0x00,0x00,0x00,0x00},/*"1",17*/
{0x18,0xC0,0x21,0x40,0x22,0x40,0x24,0x40,0x18,0x40,0x00,0x00},/*"2",18*/
{0x10,0x80,0x20,0x40,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"3",19*/
{0x02,0x00,0x0D,0x00,0x11,0x00,0x3F,0xC0,0x01,0x40,0x00,0x00},/*"4",20*/
{0x3C,0x80,0x24,0x40,0x24,0x40,0x24,0x40,0x23,0x80,0x00,0x00},/*"5",21*/
{0x1F,0x80,0x24,0x40,0x24,0x40,0x34,0x40,0x03,0x80,0x00,0x00},/*"6",22*/
{0x30,0x00,0x20,0x00,0x27,0xC0,0x38,0x00,0x20,0x00,0x00,0x00},/*"7",23*/
{0x1B,0x80,0x24,0x40,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"8",24*/
{0x1C,0x00,0x22,0xC0,0x22,0x40,0x22,0x40,0x1F,0x80,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x08,0x40,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x04,0x60,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x04,0x00,0x0A,0x00,0x11,0x00,0x20,0x80,0x40,0x40},/*"<",28*/
{0x09,0x00,0x09,0x00,0x09,0x00,0x09,0x00,0x09,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x40,0x40,0x20,0x80,0x11,0x00,0x0A,0x00,0x04,0x00},/*">",30*/
{0x18,0x00,0x20,0x00,0x23,0x40,0x24,0x00,0x18,0x00,0x00,0x00},/*"?",31*/
{0x1F,0x80,0x20,0x40,0x27,0x40,0x29,0x40,0x1F,0x40,0x00,0x00},/*"@",32*/
{0x00,0x40,0x07,0xC0,0x39,0x00,0x0F,0x00,0x01,0xC0,0x00,0x40},/*"A",33*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"B",34*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x30,0x80,0x00,0x00},/*"C",35*/
{0x20,0x40,0x3F,0xC0,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"D",36*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x2E,0x40,0x30,0xC0,0x00,0x00},/*"E",37*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x2E,0x00,0x30,0x00,0x00,0x00},/*"F",38*/
{0x0F,0x00,0x10,0x80,0x20,0x40,0x22,0x40,0x33,0x80,0x02,0x00},/*"G",39*/
{0x20,0x40,0x3F,0xC0,0x04,0x00,0x04,0x00,0x3F,0xC0,0x20,0x40},/*"H",40*/
{0x20,0x40,0x20,0x40,0x3F,0xC0,0x20,0x40,0x20,0x40,0x00,0x00},/*"I",41*/
{0x00,0x60,0x20,0x20,0x20,0x20,0x3F,0xC0,0x20,0x00,0x20,0x00},/*"J",42*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x0B,0x00,0x30,0xC0,0x20,0x40},/*"K",43*/
{0x20,0x40,0x3F,0xC0,0x20,0x40,0x00,0x40,0x00,0x40,0x00,0xC0},/*"L",44*/
{0x3F,0xC0,0x3C,0x00,0x03,0xC0,0x3C,0x00,0x3F,0xC0,0x00,0x00},/*"M",45*/
{0x20,0x40,0x3F,0xC0,0x0C,0x40,0x23,0x00,0x3F,0xC0,0x20,0x00},/*"N",46*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"O",47*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x24,0x00,0x18,0x00,0x00,0x00},/*"P",48*/
{0x1F,0x80,0x21,0x40,0x21,0x40,0x20,0xE0,0x1F,0xA0,0x00,0x00},/*"Q",49*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x26,0x00,0x19,0xC0,0x00,0x40},/*"R",50*/
{0x18,0xC0,0x24,0x40,0x24,0x40,0x22,0x40,0x31,0x80,0x00,0x00},/*"S",51*/
{0x30,0x00,0x20,0x40,0x3F,0xC0,0x20,0x40,0x30,0x00,0x00,0x00},/*"T",52*/
{0x20,0x00,0x3F,0x80,0x00,0x40,0x00,0x40,0x3F,0x80,0x20,0x00},/*"U",53*/
{0x20,0x00,0x3E,0x00,0x01,0xC0,0x07,0x00,0x38,0x00,0x20,0x00},/*"V",54*/
{0x38,0x00,0x07,0xC0,0x3C,0x00,0x07,0xC0,0x38,0x00,0x00,0x00},/*"W",55*/
{0x20,0x40,0x39,0xC0,0x06,0x00,0x39,0xC0,0x20,0x40,0x00,0x00},/*"X",56*/
{0x20,0x00,0x38,0x40,0x07,0xC0,0x38,0x40,0x20,0x00,0x00,0x00},/*"Y",57*/
{0x30,0x40,0x21,0xC0,0x26,0x40,0x38,0x40,0x20,0xC0,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x7F,0xE0,0x40,0x20,0x40,0x20,0x00,0x00},/*"[",59*/
{0x00,0x00,0x70,0x00,0x0C,0x00,0x03,0x80,0x00,0x40,0x00,0x00},/*"\",60*/
{0x00,0x00,0x40,0x20,0x40,0x20,0x7F,0xE0,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x20,0x00,0x40,0x00,0x20,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10},/*"_",63*/
{0x00,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x02,0x80,0x05,0x40,0x05,0x40,0x03,0xC0,0x00,0x40},/*"a",65*/
{0x20,0x00,0x3F,0xC0,0x04,0x40,0x04,0x40,0x03,0x80,0x00,0x00},/*"b",66*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x40,0x06,0x40,0x00,0x00},/*"c",67*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x24,0x40,0x3F,0xC0,0x00,0x40},/*"d",68*/
{0x00,0x00,0x03,0x80,0x05,0x40,0x05,0x40,0x03,0x40,0x00,0x00},/*"e",69*/
{0x00,0x00,0x04,0x40,0x1F,0xC0,0x24,0x40,0x24,0x40,0x20,0x00},/*"f",70*/
{0x00,0x00,0x02,0xE0,0x05,0x50,0x05,0x50,0x06,0x50,0x04,0x20},/*"g",71*/
{0x20,0x40,0x3F,0xC0,0x04,0x40,0x04,0x00,0x03,0xC0,0x00,0x40},/*"h",72*/
{0x00,0x00,0x04,0x40,0x27,0xC0,0x00,0x40,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x10,0x00,0x10,0x04,0x10,0x27,0xE0,0x00,0x00,0x00,0x00},/*"j",74*/
{0x20,0x40,0x3F,0xC0,0x01,0x40,0x07,0x00,0x04,0xC0,0x04,0x40},/*"k",75*/
{0x20,0x40,0x20,0x40,0x3F,0xC0,0x00,0x40,0x00,0x40,0x00,0x00},/*"l",76*/
{0x07,0xC0,0x04,0x00,0x07,0xC0,0x04,0x00,0x03,0xC0,0x00,0x00},/*"m",77*/
{0x04,0x40,0x07,0xC0,0x04,0x40,0x04,0x00,0x03,0xC0,0x00,0x40},/*"n",78*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x40,0x03,0x80,0x00,0x00},/*"o",79*/
{0x04,0x10,0x07,0xF0,0x04,0x50,0x04,0x40,0x03,0x80,0x00,0x00},/*"p",80*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x50,0x07,0xF0,0x00,0x10},/*"q",81*/
{0x04,0x40,0x07,0xC0,0x02,0x40,0x04,0x00,0x04,0x00,0x00,0x00},/*"r",82*/
{0x00,0x00,0x06,0x40,0x05,0x40,0x05,0x40,0x04,0xC0,0x00,0x00},/*"s",83*/
{0x00,0x00,0x04,0x00,0x1F,0x80,0x04,0x40,0x00,0x40,0x00,0x00},/*"t",84*/
{0x04,0x00,0x07,0x80,0x00,0x40,0x04,0x40,0x07,0xC0,0x00,0x40},/*"u",85*/
{0x04,0x00,0x07,0x00,0x04,0xC0,0x01,0x80,0x06,0x00,0x04,0x00},/*"v",86*/
{0x06,0x00,0x01,0xC0,0x07,0x00,0x01,0xC0,0x06,0x00,0x00,0x00},/*"w",87*/
{0x04,0x40,0x06,0xC0,0x01,0x00,0x06,0xC0,0x04,0x40,0x00,0x00},/*"x",88*/
{0x04,0x10,0x07,0x10,0x04,0xE0,0x01,0x80,0x06,0x00,0x04,0x00},/*"y",89*/
{0x00,0x00,0x04,0x40,0x05,0xC0,0x06,0x40,0x04,0x40,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x04,0x00,0x7B,0xE0,0x40,0x20,0x00,0x00},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xF0,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x40,0x20,0x7B,0xE0,0x04,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x40,0x00,0x80,0x00,0x40,0x00,0x20,0x00,0x20,0x00,0x40,0x00},/*"~",94*/
};
const unsigned char oled_asc2_1608[95][16]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xCC,0x00,0x0C,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x08,0x00,0x30,0x00,0x60,0x00,0x08,0x00,0x30,0x00,0x60,0x00,0x00,0x00},/*""",2*/
{0x02,0x20,0x03,0xFC,0x1E,0x20,0x02,0x20,0x03,0xFC,0x1E,0x20,0x02,0x20,0x00,0x00},/*"#",3*/
{0x00,0x00,0x0E,0x18,0x11,0x04,0x3F,0xFF,0x10,0x84,0x0C,0x78,0x00,0x00,0x00,0x00},/*"$",4*/
{0x0F,0x00,0x10,0x84,0x0F,0x38,0x00,0xC0,0x07,0x78,0x18,0x84,0x00,0x78,0x00,0x00},/*"%",5*/
{0x00,0x78,0x0F,0x84,0x10,0xC4,0x11,0x24,0x0E,0x98,0x00,0xE4,0x00,0x84,0x00,0x08},/*"&",6*/
{0x08,0x00,0x68,0x00,0x70,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xE0,0x18,0x18,0x20,0x04,0x40,0x02,0x00,0x00},/*"(",8*/
{0x00,0x00,0x40,0x02,0x20,0x04,0x18,0x18,0x07,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*")",9*/
{0x02,0x40,0x02,0x40,0x01,0x80,0x0F,0xF0,0x01,0x80,0x02,0x40,0x02,0x40,0x00,0x00},/*"*",10*/
{0x00,0x80,0x00,0x80,0x00,0x80,0x0F,0xF8,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x00},/*"+",11*/
{0x00,0x01,0x00,0x0D,0x00,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80},/*"-",13*/
{0x00,0x00,0x00,0x0C,0x00,0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x06,0x00,0x18,0x00,0x60,0x01,0x80,0x06,0x00,0x18,0x00,0x20,0x00},/*"/",15*/
{0x00,0x00,0x07,0xF0,0x08,0x08,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"0",16*/
{0x00,0x00,0x08,0x04,0x08,0x04,0x1F,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"1",17*/
{0x00,0x00,0x0E,0x0C,0x10,0x14,0x10,0x24,0x10,0x44,0x11,0x84,0x0E,0x0C,0x00,0x00},/*"2",18*/
{0x00,0x00,0x0C,0x18,0x10,0x04,0x11,0x04,0x11,0x04,0x12,0x88,0x0C,0x70,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0xE0,0x03,0x20,0x04,0x24,0x08,0x24,0x1F,0xFC,0x00,0x24,0x00,0x00},/*"4",20*/
{0x00,0x00,0x1F,0x98,0x10,0x84,0x11,0x04,0x11,0x04,0x10,0x88,0x10,0x70,0x00,0x00},/*"5",21*/
{0x00,0x00,0x07,0xF0,0x08,0x88,0x11,0x04,0x11,0x04,0x18,0x88,0x00,0x70,0x00,0x00},/*"6",22*/
{0x00,0x00,0x1C,0x00,0x10,0x00,0x10,0xFC,0x13,0x00,0x1C,0x00,0x10,0x00,0x00,0x00},/*"7",23*/
{0x00,0x00,0x0E,0x38,0x11,0x44,0x10,0x84,0x10,0x84,0x11,0x44,0x0E,0x38,0x00,0x00},/*"8",24*/
{0x00,0x00,0x07,0x00,0x08,0x8C,0x10,0x44,0x10,0x44,0x08,0x88,0x07,0xF0,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x0C,0x03,0x0C,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x00,0x80,0x01,0x40,0x02,0x20,0x04,0x10,0x08,0x08,0x10,0x04,0x00,0x00},/*"<",28*/
{0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x00,0x00},/*"=",29*/
{0x00,0x00,0x10,0x04,0x08,0x08,0x04,0x10,0x02,0x20,0x01,0x40,0x00,0x80,0x00,0x00},/*">",30*/
{0x00,0x00,0x0E,0x00,0x12,0x00,0x10,0x0C,0x10,0x6C,0x10,0x80,0x0F,0x00,0x00,0x00},/*"?",31*/
{0x03,0xE0,0x0C,0x18,0x13,0xE4,0x14,0x24,0x17,0xC4,0x08,0x28,0x07,0xD0,0x00,0x00},/*"@",32*/
{0x00,0x04,0x00,0x3C,0x03,0xC4,0x1C,0x40,0x07,0x40,0x00,0xE4,0x00,0x1C,0x00,0x04},/*"A",33*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x04,0x11,0x04,0x0E,0x88,0x00,0x70,0x00,0x00},/*"B",34*/
{0x03,0xE0,0x0C,0x18,0x10,0x04,0x10,0x04,0x10,0x04,0x10,0x08,0x1C,0x10,0x00,0x00},/*"C",35*/
{0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"D",36*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x04,0x17,0xC4,0x10,0x04,0x08,0x18,0x00,0x00},/*"E",37*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x00,0x17,0xC0,0x10,0x00,0x08,0x00,0x00,0x00},/*"F",38*/
{0x03,0xE0,0x0C,0x18,0x10,0x04,0x10,0x04,0x10,0x44,0x1C,0x78,0x00,0x40,0x00,0x00},/*"G",39*/
{0x10,0x04,0x1F,0xFC,0x10,0x84,0x00,0x80,0x00,0x80,0x10,0x84,0x1F,0xFC,0x10,0x04},/*"H",40*/
{0x00,0x00,0x10,0x04,0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x04,0x00,0x00,0x00,0x00},/*"I",41*/
{0x00,0x03,0x00,0x01,0x10,0x01,0x10,0x01,0x1F,0xFE,0x10,0x00,0x10,0x00,0x00,0x00},/*"J",42*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x03,0x80,0x14,0x64,0x18,0x1C,0x10,0x04,0x00,0x00},/*"K",43*/
{0x10,0x04,0x1F,0xFC,0x10,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x0C,0x00,0x00},/*"L",44*/
{0x10,0x04,0x1F,0xFC,0x1F,0x00,0x00,0xFC,0x1F,0x00,0x1F,0xFC,0x10,0x04,0x00,0x00},/*"M",45*/
{0x10,0x04,0x1F,0xFC,0x0C,0x04,0x03,0x00,0x00,0xE0,0x10,0x18,0x1F,0xFC,0x10,0x00},/*"N",46*/
{0x07,0xF0,0x08,0x08,0x10,0x04,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"O",47*/
{0x10,0x04,0x1F,0xFC,0x10,0x84,0x10,0x80,0x10,0x80,0x10,0x80,0x0F,0x00,0x00,0x00},/*"P",48*/
{0x07,0xF0,0x08,0x18,0x10,0x24,0x10,0x24,0x10,0x1C,0x08,0x0A,0x07,0xF2,0x00,0x00},/*"Q",49*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x00,0x11,0xC0,0x11,0x30,0x0E,0x0C,0x00,0x04},/*"R",50*/
{0x00,0x00,0x0E,0x1C,0x11,0x04,0x10,0x84,0x10,0x84,0x10,0x44,0x1C,0x38,0x00,0x00},/*"S",51*/
{0x18,0x00,0x10,0x00,0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x00,0x18,0x00,0x00,0x00},/*"T",52*/
{0x10,0x00,0x1F,0xF8,0x10,0x04,0x00,0x04,0x00,0x04,0x10,0x04,0x1F,0xF8,0x10,0x00},/*"U",53*/
{0x10,0x00,0x1E,0x00,0x11,0xE0,0x00,0x1C,0x00,0x70,0x13,0x80,0x1C,0x00,0x10,0x00},/*"V",54*/
{0x1F,0xC0,0x10,0x3C,0x00,0xE0,0x1F,0x00,0x00,0xE0,0x10,0x3C,0x1F,0xC0,0x00,0x00},/*"W",55*/
{0x10,0x04,0x18,0x0C,0x16,0x34,0x01,0xC0,0x01,0xC0,0x16,0x34,0x18,0x0C,0x10,0x04},/*"X",56*/
{0x10,0x00,0x1C,0x00,0x13,0x04,0x00,0xFC,0x13,0x04,0x1C,0x00,0x10,0x00,0x00,0x00},/*"Y",57*/
{0x08,0x04,0x10,0x1C,0x10,0x64,0x10,0x84,0x13,0x04,0x1C,0x04,0x10,0x18,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFE,0x40,0x02,0x40,0x02,0x40,0x02,0x00,0x00},/*"[",59*/
{0x00,0x00,0x30,0x00,0x0C,0x00,0x03,0x80,0x00,0x60,0x00,0x1C,0x00,0x03,0x00,0x00},/*"\",60*/
{0x00,0x00,0x40,0x02,0x40,0x02,0x40,0x02,0x7F,0xFE,0x00,0x00,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x00,0x00},/*"^",62*/
{0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01},/*"_",63*/
{0x00,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x98,0x01,0x24,0x01,0x44,0x01,0x44,0x01,0x44,0x00,0xFC,0x00,0x04},/*"a",65*/
{0x10,0x00,0x1F,0xFC,0x00,0x88,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x70,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x11,0x08,0x1F,0xFC,0x00,0x04},/*"d",68*/
{0x00,0x00,0x00,0xF8,0x01,0x44,0x01,0x44,0x01,0x44,0x01,0x44,0x00,0xC8,0x00,0x00},/*"e",69*/
{0x00,0x00,0x01,0x04,0x01,0x04,0x0F,0xFC,0x11,0x04,0x11,0x04,0x11,0x00,0x18,0x00},/*"f",70*/
{0x00,0x00,0x00,0xD6,0x01,0x29,0x01,0x29,0x01,0x29,0x01,0xC9,0x01,0x06,0x00,0x00},/*"g",71*/
{0x10,0x04,0x1F,0xFC,0x00,0x84,0x01,0x00,0x01,0x00,0x01,0x04,0x00,0xFC,0x00,0x04},/*"h",72*/
{0x00,0x00,0x01,0x04,0x19,0x04,0x19,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x03,0x00,0x01,0x01,0x01,0x19,0x01,0x19,0xFE,0x00,0x00,0x00,0x00},/*"j",74*/
{0x10,0x04,0x1F,0xFC,0x00,0x24,0x00,0x40,0x01,0xB4,0x01,0x0C,0x01,0x04,0x00,0x00},/*"k",75*/
{0x00,0x00,0x10,0x04,0x10,0x04,0x1F,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"l",76*/
{0x01,0x04,0x01,0xFC,0x01,0x04,0x01,0x00,0x01,0xFC,0x01,0x04,0x01,0x00,0x00,0xFC},/*"m",77*/
{0x01,0x04,0x01,0xFC,0x00,0x84,0x01,0x00,0x01,0x00,0x01,0x04,0x00,0xFC,0x00,0x04},/*"n",78*/
{0x00,0x00,0x00,0xF8,0x01,0x04,0x01,0x04,0x01,0x04,0x01,0x04,0x00,0xF8,0x00,0x00},/*"o",79*/
{0x01,0x01,0x01,0xFF,0x00,0x85,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x70,0x00,0x00},/*"p",80*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x01,0x05,0x01,0xFF,0x00,0x01},/*"q",81*/
{0x01,0x04,0x01,0x04,0x01,0xFC,0x00,0x84,0x01,0x04,0x01,0x00,0x01,0x80,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0xCC,0x01,0x24,0x01,0x24,0x01,0x24,0x01,0x24,0x01,0x98,0x00,0x00},/*"s",83*/
{0x00,0x00,0x01,0x00,0x01,0x00,0x07,0xF8,0x01,0x04,0x01,0x04,0x00,0x00,0x00,0x00},/*"t",84*/
{0x01,0x00,0x01,0xF8,0x00,0x04,0x00,0x04,0x00,0x04,0x01,0x08,0x01,0xFC,0x00,0x04},/*"u",85*/
{0x01,0x00,0x01,0x80,0x01,0x70,0x00,0x0C,0x00,0x10,0x01,0x60,0x01,0x80,0x01,0x00},/*"v",86*/
{0x01,0xF0,0x01,0x0C,0x00,0x30,0x01,0xC0,0x00,0x30,0x01,0x0C,0x01,0xF0,0x01,0x00},/*"w",87*/
{0x00,0x00,0x01,0x04,0x01,0x8C,0x00,0x74,0x01,0x70,0x01,0x8C,0x01,0x04,0x00,0x00},/*"x",88*/
{0x01,0x01,0x01,0x81,0x01,0x71,0x00,0x0E,0x00,0x18,0x01,0x60,0x01,0x80,0x01,0x00},/*"y",89*/
{0x00,0x00,0x01,0x84,0x01,0x0C,0x01,0x34,0x01,0x44,0x01,0x84,0x01,0x0C,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x3E,0xFC,0x40,0x02,0x40,0x02},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x40,0x02,0x40,0x02,0x3E,0xFC,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x00,0x60,0x00,0x80,0x00,0x80,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x20,0x00},/*"~",94*/
};#endif /* OLEDFONT_H_ */

4.初始化驱动

在main函数下while前添加初始化驱动

  OLED_Init();OLED_Clear();OLED_Display_On();int cnt=0;

在main函数下while循环里添加测试代码

	  	  cnt = cnt + 1;if(cnt > 99){cnt=0;}OLED_ShowString(0,5,"TEST-ok");//显示字符OLED_ShowNumber(30,30,cnt,2,16);//显示数字HAL_Delay(100);OLED_Refresh_Gram();

image-20240522224554122

5.编译烧录

image-20240522225718292

如果有snprintf有报错，Properties里勾选上这两个设置支持浮点型

image-20240522225514915

image-20240522225325148

软件SPI接线

OLEDSTM32
GNDGND
VCC3.3V
SCLPC1
SDAPC2
RESPC3
DCPC0

上电开机，屏幕点亮，显示TEST-ok，计数累加，功能正常

image-20240522231333525

硬件SPI配置

硬件SPI的配置和软件SPI配置一样，最大区别在于引脚设置的时候，SCL和SDA由硬件SPI来配置；

因此硬件SPI的配置可以直接在上边的软件SPI基础上修改；

硬件SPI和软件SPI的区别在于，前者是通过硬件寄存器操纵数据的收发，后者是通过GPIO控制引脚电平高低模拟信号的收发；因此OLED驱动逻辑上基本是一样的，只需要修改数据收发部分即可；

首先，在CubeIDE上配置硬件SPI通道

然后软件修改发数据信号部分，将原来的软件for循环模拟发送数据改成硬件SPI的HAL库发送数据接口

HAL_SPI_Transmit(&hspi1, &dat, 1, 10);

配置到这里就已经可以使用了，如果还需要启动DMA按下边配置

硬件SPI启动DMA

添加一个SPI_TX的DMA通道，其他设置保持默认即可

image-20240524185212733

软件需要修改为使用HAL_SPI_Transmit_DMA

image-20240524190008784

硬件SPI接线

从CubeIDE可视化视图可以看出，创建硬件SPI后，生成了新的SCL（SPI1_SCK）和SDA（SPI1_MOSI）引脚，因此，硬件SPI的接线只需要在原软件SPI接线的基础上，修改SCL和SDA接线即可

OLEDSTM32
GNDGND
VCC3.3V
SCLPA5(改)
SDAPA7(改)
RESPC3
DCPC0

最后是烧录程序，上电开机，屏幕点亮，显示TEST-ok，计数累加，功能正常，硬件SPI也OK了

工程源码

HAL库软件SPI驱动6针OLED例程链接：

https://pan.baidu.com/s/1QDPelPzFy8Cj5GW-YMKyXQ
提取码：1023

HAL库硬件SPI驱动6针OLED例程链接：

https://pan.baidu.com/s/1EempEbAAIQPSpyTfPNZh5Q
提取码：1023

参考链接

软件SPI参考链接：http://t.csdnimg.cn/4K2yB

硬件SPI参考链接：http://t.csdnimg.cn/pmD43

本文来自互联网用户投稿，该文观点仅代表作者本人，不代表本站立场。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如若转载，请注明出处：http://www.rhkb.cn/news/331927.html

如若内容造成侵权/违法违规/事实不符，请联系长河编程网进行投诉反馈email:809451989@qq.com，一经查实，立即删除！

相关文章

Docker 模块在宝塔中怎么使用

Docker 模块在宝塔中怎么使用

么是 Docker&#xff1f; Docker 是一个用于开发、发布和运行应用程序的开放平台。Docker 使您能够将应用程序与基础架构分离&#xff0c;以便您可以快速交付软件。使用 Docker&#xff0c;您可以像管理应用程序一样管理基础设施。通过利用 Docker 快速交付、测试和部署代码的方…
阅读更多...
LabVIEW步开发进电机的串口控制程序

LabVIEW步开发进电机的串口控制程序

LabVIEW步开发进电机的串口控制程序 为了提高电机控制的精确度和自动化程度&#xff0c;开发一种基于LabVIEW的实时、自动化电机串口控制程序。利用LabVIEW软件的图形化编程特性&#xff0c;通过串口实时控制电机的运行参数&#xff0c;实现电机性能的精准控制与评估。 系统组…
阅读更多...
[C语言]自定义类型详解：结构体、联合体、枚举

[C语言]自定义类型详解：结构体、联合体、枚举

目录 &#x1f680;结构体 &#x1f525;结构体类型的声明 &#x1f525;结构的自引用 &#x1f525;结构体变量的定义和初始化 &#x1f525;结构体内存对齐 &#x1f525;结构体传参 &#x1f525;结构体实现位段&#xff08;位段的填充&可移植性&#xff09; &a…
阅读更多...
FFmpeg操作命令 - 精简版

FFmpeg操作命令 - 精简版

PS&#xff1a;&#xff08;因为我只需要简单的操作&#xff0c;所以我整理出了这份笔记&#xff09; 原网址&#xff1a;30分钟带你入门&#xff0c;20个 FFmpeg操作命令&#xff0c;包你学会 - 知乎 大佬零声Github整理库整理的笔记非常的全面&#xff0c;想看完整版去上面…
阅读更多...
LeetCode 第131场双周赛个人题解

LeetCode 第131场双周赛个人题解

100309. 求出出现两次数字的 XOR 值 原题链接 求出出现两次数字的 XOR 值 - 力扣 (LeetCode) 竞赛 思路分析 签到题&#xff0c;一次遍历 AC代码 class Solution:def duplicateNumbersXOR(self, nums: List[int]) -> int:cnt Counter(nums)res 0st set(nums)for x …
阅读更多...
Leetcode42题：接雨水

Leetcode42题：接雨水

1.题目描述 给定 n 个非负整数表示每个宽度为 1 的柱子的高度图&#xff0c;计算按此排列的柱子&#xff0c;下雨之后能接多少雨水。 示例1&#xff1a; 输入&#xff1a;height [0,1,0,2,1,0,1,3,2,1,2,1] 输出&#xff1a;6 解释&#xff1a;上面是由数组 [0,1,0,2,1,0,1,…
阅读更多...
【Redis】 关于 Redis 哈希类型

【Redis】 关于 Redis 哈希类型

文章目录 &#x1f343;前言&#x1f38b;命令介绍&#x1f6a9;hset&#x1f6a9;hget&#x1f6a9;hexists&#x1f6a9;hdel&#x1f6a9;hkeys&#x1f6a9;hvals&#x1f6a9;hgetall&#x1f6a9;hmget&#x1f6a9;hlen&#x1f6a9;hsetnx&#x1f6a9;hincrby&#x1…
阅读更多...
SAP-CO成本控制概念之标准成本

SAP-CO成本控制概念之标准成本

“ 本篇介绍&#xff1a;标准成本的会计概念&#xff0c;标准成本的制定标准&#xff1b;通过结合会计标准成本的概念与SAP CO标准成本估算功能&#xff0c;更具象化的了解SAP如何实现标准成本管理&#xff0c;为后续学习SAP实际成本核算打下基础。” 01 — 背景需求 SAP实施…
阅读更多...
最重要的时间表示，柯桥外贸俄语小班课

最重要的时间表示，柯桥外贸俄语小班课

в第四格 1、与表示“钟点”的数词词组连用 例&#xff1a; в шесть часов утра 在早上六点 в пять тридцать 在五点半 2、与表示“星期”的名词连用 例&#xff1a; в пятницу 在周五 в следующий понедельник …
阅读更多...
【FPGA】Verilog：奇校验位检查器的实现（Odd Parity Bit Checker）

【FPGA】Verilog：奇校验位检查器的实现（Odd Parity Bit Checker）

真值表和卡洛图 Odd Parity Bit Checker A B C
阅读更多...
LeetCode 第399场周赛个人题解

LeetCode 第399场周赛个人题解

100323. 优质数对的总数 I 原题链接 100323. 优质数对的总数 I 思路分析 签到题 AC代码 class Solution:def numberOfPairs(self, nums1: List[int], nums2: List[int], k: int) -> int:n, m len(nums1), len(nums2)ret 0for i in range(n):for j in range(m):if nu…
阅读更多...
千亿级开源大模型Qwen110B部署实测

千亿级开源大模型Qwen110B部署实测

近日&#xff0c;通义千问团队震撼开源 Qwen1.5 系列首个千亿参数模型 Qwen1.5-110B-Chat。 千亿级大模型普通显卡是跑不了推理的&#xff0c;普通人一般也没办法本地运行千亿级大模型。 为了探索千亿级大模型到底需要计算资源&#xff0c;我用云计算资源部署了Qwen1.5-110B-…
阅读更多...
Leetcode 剑指 Offer II 079.子集

Leetcode 剑指 Offer II 079.子集

题目难度: 中等 原题链接 今天继续更新 Leetcode 的剑指 Offer&#xff08;专项突击版&#xff09;系列, 大家在公众号 算法精选 里回复 剑指offer2 就能看到该系列当前连载的所有文章了, 记得关注哦~ 题目描述 给定一个整数数组 nums &#xff0c;数组中的元素 互不相同 。返…
阅读更多...
20232801 2023-2024-2 《网络攻防实践》实践十一报告

20232801 2023-2024-2 《网络攻防实践》实践十一报告

#20232801 2023-2024-2 《网络攻防实践》实践十一报告 1.实践内容 &#xff08;1&#xff09;web浏览器渗透攻击 使用攻击机和Windows靶机进行浏览器渗透攻击实验&#xff0c;体验网页木马构造及实施浏览器攻击的实际过程。 &#xff08;2&#xff09;取证分析实践—网页木马…
阅读更多...
北核论文完美复现：自适应t分布与动态边界策略改进的算术优化算法

北核论文完美复现：自适应t分布与动态边界策略改进的算术优化算法

声明&#xff1a;文章是从本人公众号中复制而来&#xff0c;因此&#xff0c;想最新最快了解各类智能优化算法及其改进的朋友&#xff0c;可关注我的公众号&#xff1a;强盛机器学习&#xff0c;不定期会有很多免费代码分享~ 目录 原始算术优化算法 改进点1&#xff1a;引入…
阅读更多...
那智不二越机器人维修案例分享

那智不二越机器人维修案例分享

那智不二越工业机器人在工业范围内广泛应用于各种生产领域。其示教器作为人机交互的重要设备&#xff0c;常常需要定期维护和Nachi不二越机械手示教盒修理。 【Nachi不二越机器人示教器维修步骤】 1. 关闭电源 在进行任何那智不二越机器人维修操作之前&#xff0c;务必确保机器…
阅读更多...
IDEA打开项目报错

IDEA打开项目报错

IDEA打开项目报错&#xff1a; Cannot read scheme C:\Users\xxxxxx\AppData\Roaming\JetBrains\IntelliJIdea2023.2\qaplug_profiles\Default.xmljava.lang.AbstractMethodError: Receiver class com.soldevelo.qaplug.scanner.AnalysisProfileManager$2 does not define or i…
阅读更多...
单条16g和双条8g哪个好

单条16g和双条8g哪个好

单条16g和双条8g各有优劣，具体选择要根据个人需求和电脑配置来决定。 以下是一些参考信息： •单条16g内存的价格比双条8g内存的价格低，而且16g的内存容量大，一条内存十分的方便。 •两条8g内存可以组成双通道，电脑运行速度要快一些。 •对于普通使用电脑的人群与热衷于…
阅读更多...
项目管理-人力资源管理

项目管理-人力资源管理

目录 一、概述 二、人力资源计划编制 2.1 概述 2.2 层次结构图 2.3 分配任务矩阵 三、组建项目团队 3.1 概述 3.2 内部谈判 3.3 事先分派 3.4 外部招聘 3.5 虚拟团队 3.6 总结 四、项目团队建设 4.1 概述 4.2 团队发展过程 4.2.1 概述 4.2.2 形成期 4.2.3 震…
阅读更多...
vue3 ts问题 找不到模块“@/views/home/index.vue”或其相应的类型声明。

vue3 ts问题 找不到模块“@/views/home/index.vue”或其相应的类型声明。

1. 找不到模块“/views/HomeView.vue”或其相应的类型声明 今天帮同事看了一个问题&#xff0c;他尝试用vitevue3tspinia创建项目&#xff0c;结果刚上来就遇到这么一个问题 2. 解决办法 出现这个问题的原因就是&#xff1a;ts只支持导出导入模块&#xff0c;但是vue不是模块…
阅读更多...
最新文章
推荐文章

Copyright @ 2022~2023