STM32存储左右互搏 模拟U盘桥接SPI总线FATS读写FLASH W25QXX

STM32存储左右互搏 模拟U盘桥接SPI总线FATS读写FLASH W25QXX

STM32的USB接口可以模拟成为U盘,通过FATS文件系统对连接的存储单元进行U盘方式的读写。
这里介绍STM32CUBEIDE开发平台HAL库模拟U盘桥接SPI总线FATS读写W25Q各型号FLASH的例程。
FLASH是常用的一种非易失存储单元,W25QXX系列Flash有不同容量的型号,如W25Q64的容量为64Mbit,也就是8MByte。

W25QXX介绍

W25QXX的SOIC封装如下所示,在采用SPI而不是QUAL SPI时,管脚定义为:
在这里插入图片描述
即由片选(/CS), 时钟(CLK), 数据输出(DO)和数据输入(DI)的组成4线SPI信号接口。VCC和GND提供电源和接地连接。

例程采用STM32H750VBT6芯片, FLASH可以选择为8/16/32/64/128/256/512/1024 Mbit的W25Q型号。例程实现可以通过U盘形式和串口控制双方式对FLASH内的文件进行操作,实现可交换操作的特性。

STM32工程配置

首先建立基本工程并设置时钟:
在这里插入图片描述
对于STM32H7,有专用的内部48MHz时钟用于USB接口, 其它应用采用内部高速时钟接口即可:
在这里插入图片描述
在这里插入图片描述
设置UART1作为通讯串口:
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
FLASH连接到了SPI2接口,对SPI2进行配置:
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
不用中断和DMA模式,SPI2的片选才用软件代码控制,配置一个GPIO作为片选输出:
在这里插入图片描述

配置USB接口
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
将USB接口例化为U盘模式:

在这里插入图片描述

在这里插入图片描述
对FATS文件系统进行配置
在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
STM32H7资源多,可以将堆栈开大些:
在这里插入图片描述

保存并生成初始工程代码:
在这里插入图片描述

STM32工程代码

UART串口printf打印输出实现参考:STM32 UART串口printf函数应用及浮点打印代码空间节省 (HAL)

建立W25Q访问的库头文件W25QXX.h:

#ifndef INC_W25QXX_H_
#define INC_W25QXX_H_#include "main.h"uint8_t SPI2_ReadWriteByte(uint8_t TxData);//W25QXX serial chip list:
#define W25Q80_ID 	0XEF13
#define W25Q16_ID 	0XEF14
#define W25Q32_ID 	0XEF15
#define W25Q64_ID 	0XEF16
#define W25Q128_ID	0XEF17
#define W25Q256_ID  0XEF18
#define W25Q512_ID  0XEF19
#define W25Q1024_ID 0XEF20extern uint16_t W25QXX_TYPE; //To indicate W25QXX type used in this procedure//W25QXX chip select control function
#define W25QXX_CS(n)  ( n ? HAL_GPIO_WritePin(GPIOB, GPIO_PIN_12, GPIO_PIN_SET) : HAL_GPIO_WritePin(GPIOB, GPIO_PIN_12, GPIO_PIN_RESET) )//command table for W25QXX access
#define W25X_WriteEnable		0x06
#define W25X_WriteDisable		0x04
#define W25X_ReadStatusReg1		0x05
#define W25X_ReadStatusReg2		0x35
#define W25X_ReadStatusReg3		0x15
#define W25X_WriteStatusReg1    0x01
#define W25X_WriteStatusReg2    0x31
#define W25X_WriteStatusReg3    0x11
#define W25X_ReadData			0x03
#define W25X_FastReadData		0x0B
#define W25X_FastReadDual		0x3B
#define W25X_PageProgram		0x02
#define W25X_BlockErase			0xD8
#define W25X_SectorErase		0x20
#define W25X_ChipErase			0xC7
#define W25X_PowerDown			0xB9
#define W25X_ReleasePowerDown	0xAB
#define W25X_DeviceID			0xAB
#define W25X_ManufactDeviceID	0x90
#define W25X_JedecDeviceID		0x9F
#define W25X_Enable4ByteAddr    0xB7
#define W25X_Exit4ByteAddr      0xE9uint8_t W25QXX_Init(void);
uint16_t  W25QXX_ReadID(void);  	    		  //Read W25QXX ID
uint8_t W25QXX_ReadSR(uint8_t reg_num);           //Read from status register
void W25QXX_4ByteAddr_Enable(void);               //Enable 4-byte address mode
void W25QXX_Write_SR(uint8_t reg_num,uint8_t d);  //Write to status register
void W25QXX_Write_Enable(void);  		          //Write enable
void W25QXX_Write_Disable(void);		          //Write disable
void W25QXX_Write_NoCheck(uint8_t* pBuffer,uint32_t WriteAddr,uint16_t NumByteToWrite); //Write operation w/o check
void W25QXX_Read(uint8_t* pBuffer,uint32_t ReadAddr,uint16_t NumByteToRead);            //Read operation
void W25QXX_Write(uint8_t* pBuffer,uint32_t WriteAddr,uint16_t NumByteToWrite);         //Write operation
void W25QXX_Erase_Chip(void);    	  	                                                //Erase whole chip
void W25QXX_Erase_Sector(uint32_t Sector_Num);	                                        //Erase sector in specific sector number
void W25QXX_Wait_Busy(void);           	       //Wait idle status before next operation
void W25QXX_PowerDown(void);        	       //Enter power-down mode
void W25QXX_WAKEUP(void);				       //Wake-up#endif /* INC_W25QXX_H_ */

建立W25Q访问的库源文件W25QXX.c:

#include "W25QXX.h"extern SPI_HandleTypeDef hspi2;
extern void PY_Delay_us_t(uint32_t Delay);
//Write and read one byte in SPI2
uint8_t SPI2_ReadWriteByte(uint8_t TxData)
{uint8_t Rxdata;HAL_SPI_TransmitReceive(&hspi2,&TxData,&Rxdata,1, 1000);return Rxdata;
}uint16_t W25QXX_TYPE=W25Q64_ID;//W25QXX initialization
uint8_t W25QXX_Init(void)
{uint8_t temp;W25QXX_CS(1);W25QXX_TYPE=W25QXX_ReadID();if((W25QXX_TYPE==W25Q256_ID)||(W25QXX_TYPE==W25Q512_ID)||(W25QXX_TYPE==W25Q1024_ID)){temp=W25QXX_ReadSR(3);              //read status register 3if((temp&0X01)==0)			        //judge address mode and configure to 4-byte address mode{W25QXX_CS(0);SPI2_ReadWriteByte(W25X_Enable4ByteAddr);W25QXX_CS(1);}}if((W25QXX_TYPE==0x0000)||(W25QXX_TYPE==0xFFFF)) return 0;else return 1;
}//Read status registers of W25QXX
//reg_num: register number from 1 to 3
//return: value of selected register//SR1 (default 0x00):
//BIT7  6   5   4   3   2   1   0
//SPR   RV  TB BP2 BP1 BP0 WEL BUSY
//SPR: default 0, status register protection bit used with WP
//TB,BP2,BP1,BP0: FLASH region write protection configuration
//WEL: write enable lock
//BUSY: busy flag (1: busy; 0: idle)//SR2:
//BIT7  6   5   4   3   2   1   0
//SUS   CMP LB3 LB2 LB1 (R) QE  SRP1//SR3:
//BIT7      6    5    4   3   2   1   0
//HOLD/RST  DRV1 DRV0 (R) (R) WPS ADP ADS
uint8_t W25QXX_ReadSR(uint8_t reg_num)
{uint8_t byte=0,command=0;switch(reg_num){case 1:command=W25X_ReadStatusReg1;    //To read status register 1break;case 2:command=W25X_ReadStatusReg2;    //To read status register 2break;case 3:command=W25X_ReadStatusReg3;    //To read status register 3break;default:command=W25X_ReadStatusReg1;break;}W25QXX_CS(0);SPI2_ReadWriteByte(command);    //send commandbyte=SPI2_ReadWriteByte(0Xff);  //read dataW25QXX_CS(1);return byte;
}//Write status registers of W25QXX
//reg_num: register number from 1 to 3
//d: data for updating status register
void W25QXX_Write_SR(uint8_t reg_num,uint8_t d)
{uint8_t command=0;switch(reg_num){case 1:command=W25X_WriteStatusReg1;    //To write status register 1break;case 2:command=W25X_WriteStatusReg2;    //To write status register 2break;case 3:command=W25X_WriteStatusReg3;    //To write status register 3break;default:command=W25X_WriteStatusReg1;break;}W25QXX_CS(0);SPI2_ReadWriteByte(command);            //send commandSPI2_ReadWriteByte(d);                  //write dataW25QXX_CS(1);
}
//W25QXX write enable
void W25QXX_Write_Enable(void)
{W25QXX_CS(0);SPI2_ReadWriteByte(W25X_WriteEnable);W25QXX_CS(1);
}
//W25QXX write disable
void W25QXX_Write_Disable(void)
{W25QXX_CS(0);SPI2_ReadWriteByte(W25X_WriteDisable);W25QXX_CS(1);
}//Read chip ID
//return:
//0XEF13 for W25Q80
//0XEF14 for W25Q16
//0XEF15 for W25Q32
//0XEF16 for W25Q64
//0XEF17 for W25Q128
//0XEF18 for W25Q256
uint16_t W25QXX_ReadID(void)
{uint16_t Temp = 0;W25QXX_CS(0);SPI2_ReadWriteByte(0x90);          //send commandSPI2_ReadWriteByte(0x00);SPI2_ReadWriteByte(0x00);SPI2_ReadWriteByte(0x00);Temp|=SPI2_ReadWriteByte(0xFF)<<8; //read high byte dataTemp|=SPI2_ReadWriteByte(0xFF);    //read low byte dataW25QXX_CS(1);return Temp;
}
//Read W25QXX from specific address for specific byte length
//pBuffer: data buffer
//ReadAddr: specific address
//NumByteToRead: specific byte length (max 65535)
void W25QXX_Read(uint8_t* pBuffer,uint32_t ReadAddr,uint16_t NumByteToRead)
{uint16_t i;W25QXX_CS(0);SPI2_ReadWriteByte(W25X_ReadData);                   //send read commandif((W25QXX_TYPE==W25Q256_ID)||(W25QXX_TYPE==W25Q512_ID)||(W25QXX_TYPE==W25Q1024_ID))  //send highest 8-bit address{SPI2_ReadWriteByte((uint8_t)((ReadAddr)>>24));}SPI2_ReadWriteByte((uint8_t)((ReadAddr)>>16));       //send 24-bit addressSPI2_ReadWriteByte((uint8_t)((ReadAddr)>>8));SPI2_ReadWriteByte((uint8_t)ReadAddr);for(i=0;i<NumByteToRead;i++){pBuffer[i]=SPI2_ReadWriteByte(0XFF);             //read data}W25QXX_CS(1);
}//Write W25QXX not more than 1 page (256 bytes)
//pBuffer: data buffer
//WriteAddr: specific address
//NumByteToWrite: specific byte length (max 256)
void W25QXX_Write_Page(uint8_t* pBuffer,uint32_t WriteAddr,uint16_t NumByteToWrite)
{uint16_t i;W25QXX_Write_Enable();                                       //write enableW25QXX_CS(0);SPI2_ReadWriteByte(W25X_PageProgram);                        //send write commandif((W25QXX_TYPE==W25Q256_ID)||(W25QXX_TYPE==W25Q512_ID)||(W25QXX_TYPE==W25Q1024_ID)) //send highest 8-bit address{SPI2_ReadWriteByte((uint8_t)((WriteAddr)>>24));}SPI2_ReadWriteByte((uint8_t)((WriteAddr)>>16));               //send 24-bit addressSPI2_ReadWriteByte((uint8_t)((WriteAddr)>>8));SPI2_ReadWriteByte((uint8_t)WriteAddr);for(i=0;i<NumByteToWrite;i++)SPI2_ReadWriteByte(pBuffer[i]);  //write dataW25QXX_CS(1);W25QXX_Wait_Busy();
}//Write W25QXX w/o erase check and w/o byte number restriction
//pBuffer: data buffer
//WriteAddr: specific address
//NumByteToWrite: specific byte length (max 65535)
void W25QXX_Write_NoCheck(uint8_t* pBuffer,uint32_t WriteAddr,uint16_t NumByteToWrite)
{uint16_t remained_byte_num_in_page;remained_byte_num_in_page=256-WriteAddr%256;                                                       //remained byte number in pageif( NumByteToWrite <= remained_byte_num_in_page ) remained_byte_num_in_page = NumByteToWrite;      //data can be written in single pagewhile(1){W25QXX_Write_Page(pBuffer,WriteAddr,remained_byte_num_in_page);if(NumByteToWrite==remained_byte_num_in_page)break;                                            //end write operationelse                                                                                           //NumByteToWrite>remained_byte_num_in_page{pBuffer+=remained_byte_num_in_page;WriteAddr+=remained_byte_num_in_page;NumByteToWrite-=remained_byte_num_in_page;if(NumByteToWrite>256)remained_byte_num_in_page=256;                                       //for whole page writeelse remained_byte_num_in_page=NumByteToWrite; 	                                           //for non-whole page write}};
}//Write W25QXX w/ erase after check and w/o byte number restriction
//pBuffer: data buffer
//WriteAddr: specific address
//NumByteToWrite: specific byte length (max 65535)
uint8_t W25QXX_BUFFER[4096];
void W25QXX_Write(uint8_t* pBuffer,uint32_t WriteAddr,uint16_t NumByteToWrite)
{uint32_t secpos;uint16_t secoff;uint16_t secremain;uint16_t i;uint8_t * W25QXX_BUF;W25QXX_BUF=W25QXX_BUFFER;secpos=WriteAddr/4096;                                        //sector number (16 pages for 1 sector) for destination addresssecoff=WriteAddr%4096;                                        //offset address in sector for destination addresssecremain=4096-secoff;                                        //remained space for sectorif(NumByteToWrite<=secremain)secremain=NumByteToWrite;        //data can be written in single sectorwhile(1){W25QXX_Read(W25QXX_BUF,secpos*4096,4096);                 //read sector data for ease necessity judgmentfor(i=0;i<secremain;i++)                                  //check sector data status{if(W25QXX_BUF[secoff+i]!=0XFF) break;                 //ease necessary}if(i<secremain)                                           //for ease{W25QXX_Erase_Sector(secpos);                          //ease sectorfor(i=0;i<secremain;i++)	                          //data copy{W25QXX_BUF[i+secoff]=pBuffer[i];}W25QXX_Write_NoCheck(W25QXX_BUF,secpos*4096,4096);     //write sector}else W25QXX_Write_NoCheck(pBuffer,WriteAddr,secremain);   //write data for sector unnecessary to eraseif(NumByteToWrite==secremain)break;                        //for operation endelse                                                       //for operation continuing{secpos++;                                              //sector number + 1secoff=0;                                              //offset address from 0pBuffer+=secremain;                                    //pointer adjustmentWriteAddr+=secremain;                                  //write address adjustmentNumByteToWrite-=secremain;				               //write number adjustmentif(NumByteToWrite>4096) secremain=4096;	               //not last sectorelse secremain=NumByteToWrite;			               //last sector}};
}//Erase whole chip, long waiting...
void W25QXX_Erase_Chip(void)
{W25QXX_Write_Enable();                  //write enableW25QXX_Wait_Busy();W25QXX_CS(0);SPI2_ReadWriteByte(W25X_ChipErase);     //send erase commandW25QXX_CS(1);W25QXX_Wait_Busy();   				    //wait for erase complete
}//Erase one sector
//Sector_Num: sector number
void W25QXX_Erase_Sector(uint32_t Sector_Num)
{Sector_Num*=4096;W25QXX_Write_Enable();                                     //write enableW25QXX_Wait_Busy();W25QXX_CS(0);SPI2_ReadWriteByte(W25X_SectorErase);                      //send erase commandif((W25QXX_TYPE==W25Q256_ID)||(W25QXX_TYPE==W25Q512_ID)||(W25QXX_TYPE==W25Q1024_ID)) //send highest 8-bit address{SPI2_ReadWriteByte((uint8_t)((Sector_Num)>>24));}SPI2_ReadWriteByte((uint8_t)((Sector_Num)>>16));           //send 24-bit addressSPI2_ReadWriteByte((uint8_t)((Sector_Num)>>8));SPI2_ReadWriteByte((uint8_t)Sector_Num);W25QXX_CS(1);W25QXX_Wait_Busy();   				                       //wait for erase complete
}//Wait idle status before next operation
void W25QXX_Wait_Busy(void)
{while((W25QXX_ReadSR(1)&0x01)==0x01);    //wait for busy flag cleared
}//Enter power-down mode
#define tDP_us 3
void W25QXX_PowerDown(void)
{W25QXX_CS(0);SPI2_ReadWriteByte(W25X_PowerDown);      //send power-down commandW25QXX_CS(1);PY_Delay_us_t(tDP_us);                   //tDP
}
//Wake-up
#define tRES1_us 3
void W25QXX_WAKEUP(void)
{W25QXX_CS(0);SPI2_ReadWriteByte(W25X_ReleasePowerDown);//send release power-down commandW25QXX_CS(1);PY_Delay_us_t(tRES1_us);                  //tRES1
}

对ffconf.h添加包含信息:
在这里插入图片描述

#include "main.h"
#include "stm32h7xx_hal.h"

修改user_diskio.c,对文件操作函数与底层FLASH读写提供连接:

/* USER CODE BEGIN Header */
/********************************************************************************* @file    user_diskio.c* @brief   This file includes a diskio driver skeleton to be completed by the user.******************************************************************************* @attention** Copyright (c) 2023 STMicroelectronics.* All rights reserved.** This software is licensed under terms that can be found in the LICENSE file* in the root directory of this software component.* If no LICENSE file comes with this software, it is provided AS-IS.********************************************************************************//* USER CODE END Header */#ifdef USE_OBSOLETE_USER_CODE_SECTION_0
/** Warning: the user section 0 is no more in use (starting from CubeMx version 4.16.0)* To be suppressed in the future.* Kept to ensure backward compatibility with previous CubeMx versions when* migrating projects.* User code previously added there should be copied in the new user sections before* the section contents can be deleted.*/
/* USER CODE BEGIN 0 */
/* USER CODE END 0 */
#endif/* USER CODE BEGIN DECL */
/**************************SELF DEFINITION PART************/
#include "diskio.h"		/* Declarations of disk functions */
#include "W25QXX.h"
/**********************************************************/
/* Includes ------------------------------------------------------------------*/
#include <string.h>
#include "ff_gen_drv.h"/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*//* Private variables ---------------------------------------------------------*/
/* Disk status */
static volatile DSTATUS Stat = STA_NOINIT;/* USER CODE END DECL *//* Private function prototypes -----------------------------------------------*/
DSTATUS USER_initialize (BYTE pdrv);
DSTATUS USER_status (BYTE pdrv);
DRESULT USER_read (BYTE pdrv, BYTE *buff, DWORD sector, UINT count);
#if _USE_WRITE == 1DRESULT USER_write (BYTE pdrv, const BYTE *buff, DWORD sector, UINT count);
#endif /* _USE_WRITE == 1 */
#if _USE_IOCTL == 1DRESULT USER_ioctl (BYTE pdrv, BYTE cmd, void *buff);
#endif /* _USE_IOCTL == 1 */Diskio_drvTypeDef  USER_Driver =
{USER_initialize,USER_status,USER_read,
#if  _USE_WRITEUSER_write,
#endif  /* _USE_WRITE == 1 */
#if  _USE_IOCTL == 1USER_ioctl,
#endif /* _USE_IOCTL == 1 */
};/* Private functions ---------------------------------------------------------*//*** @brief  Initializes a Drive* @param  pdrv: Physical drive number (0..)* @retval DSTATUS: Operation status*/
DSTATUS USER_initialize (BYTE pdrv           /* Physical drive nmuber to identify the drive */
)
{/* USER CODE BEGIN INIT *//**************************SELF DEFINITION PART************/uint8_t res;res = W25QXX_Init();if(res) return RES_OK;else return  STA_NOINIT;/**********************************************************//*Stat = STA_NOINIT;return Stat;*//* USER CODE END INIT */
}/*** @brief  Gets Disk Status* @param  pdrv: Physical drive number (0..)* @retval DSTATUS: Operation status*/
DSTATUS USER_status (BYTE pdrv       /* Physical drive number to identify the drive */
)
{/* USER CODE BEGIN STATUS *//**************************SELF DEFINITION PART************/switch (pdrv){case 0 :return RES_OK;case 1 :return RES_OK;case 2 :return RES_OK;default:return STA_NOINIT;}/**********************************************************//*Stat = STA_NOINIT;return Stat;*//* USER CODE END STATUS */
}/*** @brief  Reads Sector(s)* @param  pdrv: Physical drive number (0..)* @param  *buff: Data buffer to store read data* @param  sector: Sector address (LBA)* @param  count: Number of sectors to read (1..128)* @retval DRESULT: Operation result*/
DRESULT USER_read (BYTE pdrv,      /* Physical drive nmuber to identify the drive */BYTE *buff,     /* Data buffer to store read data */DWORD sector,   /* Sector address in LBA */UINT count      /* Number of sectors to read */
)
{/* USER CODE BEGIN READ *//**************************SELF DEFINITION PART************/uint16_t len;if( !count ){return RES_PARERR;  /* count不能等于0,否则返回参数错误 */}switch (pdrv){case 0:sector <<= 9; //Convert sector number to byte addresslen = count*512;W25QXX_Read(buff, sector, len);return RES_OK;default:return RES_ERROR;}/**********************************************************//*return RES_OK;*//* USER CODE END READ */
}/*** @brief  Writes Sector(s)* @param  pdrv: Physical drive number (0..)* @param  *buff: Data to be written* @param  sector: Sector address (LBA)* @param  count: Number of sectors to write (1..128)* @retval DRESULT: Operation result*/
#if _USE_WRITE == 1
DRESULT USER_write (BYTE pdrv,          /* Physical drive nmuber to identify the drive */const BYTE *buff,   /* Data to be written */DWORD sector,       /* Sector address in LBA */UINT count          /* Number of sectors to write */
)
{/* USER CODE BEGIN WRITE *//* USER CODE HERE *//**************************SELF DEFINITION PART************/uint16_t len;if( !count ){return RES_PARERR;  /* count不能等于0,否则返回参数错误 */}switch (pdrv){case 0:sector <<= 9; //Convert sector number to byte addresslen = count*512;W25QXX_Write((uint8_t *)buff, sector, len);return RES_OK;default:return RES_ERROR;}/*********************************************************//*return RES_OK;*//* USER CODE END WRITE */
}
#endif /* _USE_WRITE == 1 *//*** @brief  I/O control operation* @param  pdrv: Physical drive number (0..)* @param  cmd: Control code* @param  *buff: Buffer to send/receive control data* @retval DRESULT: Operation result*/
#if _USE_IOCTL == 1
DRESULT USER_ioctl (BYTE pdrv,      /* Physical drive nmuber (0..) */BYTE cmd,       /* Control code */void *buff      /* Buffer to send/receive control data */
)
{/* USER CODE BEGIN IOCTL *//**************************SELF DEFINITION PART************/#define user_sector_byte_size 512DRESULT res;switch(cmd){case CTRL_SYNC:W25QXX_Wait_Busy();res=RES_OK;break;case GET_SECTOR_SIZE:*(WORD*)buff = user_sector_byte_size;res = RES_OK;break;case GET_BLOCK_SIZE:*(WORD*)buff = 4096/user_sector_byte_size;res = RES_OK;break;case GET_SECTOR_COUNT:W25QXX_TYPE=W25QXX_ReadID();if(W25QXX_TYPE==W25Q80_ID) *(DWORD*)buff = (8*1024*1024/512);else if(W25QXX_TYPE==W25Q16_ID) *(DWORD*)buff = (16*1024*1024/512);else if(W25QXX_TYPE==W25Q32_ID) *(DWORD*)buff = (32*1024*1024/512);else if(W25QXX_TYPE==W25Q64_ID) *(DWORD*)buff = (64*1024*1024/512);else if(W25QXX_TYPE==W25Q128_ID) *(DWORD*)buff = (128*1024*1024/512);else if(W25QXX_TYPE==W25Q256_ID) *(DWORD*)buff = (256*1024*1024/512);else if(W25QXX_TYPE==W25Q512_ID) *(DWORD*)buff = (512*1024*1024/512);else if(W25QXX_TYPE==W25Q1024_ID) *(DWORD*)buff = (1024*1024*1024/512);else *(DWORD*)buff = (8*1024*1024/512);res = RES_OK;break;default:res = RES_PARERR;break;}return res;/**********************************************************//*DRESULT res = RES_ERROR;return res;*//* USER CODE END IOCTL */
}
#endif /* _USE_IOCTL == 1 */

上面配置的FATS协议是用户可操作的显式协议,譬如本例程通过串口发送指令后控制对FLASH的FATS操作。STM32的U盘接口相当于包含对PC端的握手协议和对内部的隐式FATS协议,还需要配置底层对针对的存储单元读写操作函数。
配置U盘接口包含如下部分:
引入头文件申明
在这里插入图片描述
设置U盘识别的大小参数:
在这里插入图片描述
这里0x4000对应16K,0x200对应512(字节), 16K*512=8M, 所以U盘会识别为8MB的U盘。

然后是U盘初始化的设置
在这里插入图片描述
U盘识别时获取U盘容量的函数
在这里插入图片描述
然后再配置读操作和写操作函数
在这里插入图片描述
完整的代码如下:

/* USER CODE BEGIN Header */
/********************************************************************************* @file           : usbd_storage_if.c* @version        : v1.0_Cube* @brief          : Memory management layer.******************************************************************************* @attention** Copyright (c) 2023 STMicroelectronics.* All rights reserved.** This software is licensed under terms that can be found in the LICENSE file* in the root directory of this software component.* If no LICENSE file comes with this software, it is provided AS-IS.********************************************************************************/
/* USER CODE END Header *//* Includes ------------------------------------------------------------------*/
#include "usbd_storage_if.h"/* USER CODE BEGIN INCLUDE */
#include "W25QXX.h"
/* USER CODE END INCLUDE *//* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*//* USER CODE BEGIN PV */
/* Private variables ---------------------------------------------------------*//* USER CODE END PV *//** @addtogroup STM32_USB_OTG_DEVICE_LIBRARY* @brief Usb device.* @{*//** @defgroup USBD_STORAGE* @brief Usb mass storage device module* @{*//** @defgroup USBD_STORAGE_Private_TypesDefinitions* @brief Private types.* @{*//* USER CODE BEGIN PRIVATE_TYPES */
#if 0
/* USER CODE END PRIVATE_TYPES *//*** @}*//** @defgroup USBD_STORAGE_Private_Defines* @brief Private defines.* @{*/#define STORAGE_LUN_NBR                  1
#define STORAGE_BLK_NBR                  0x10000
#define STORAGE_BLK_SIZ                  0x200/* USER CODE BEGIN PRIVATE_DEFINES */
#endif#define STORAGE_LUN_NBR                  1         //STORAGE_LUN_NBR : disk number
#define STORAGE_BLK_NBR                  0x4000    //STORAGE_BLK_NBR : block number
#define STORAGE_BLK_SIZ                  0x200     //STORAGE_BLK_SIZ : block size
/* USER CODE END PRIVATE_DEFINES *//*** @}*//** @defgroup USBD_STORAGE_Private_Macros* @brief Private macros.* @{*//* USER CODE BEGIN PRIVATE_MACRO *//* USER CODE END PRIVATE_MACRO *//*** @}*//** @defgroup USBD_STORAGE_Private_Variables* @brief Private variables.* @{*//* USER CODE BEGIN INQUIRY_DATA_FS */
/** USB Mass storage Standard Inquiry Data. */
const int8_t STORAGE_Inquirydata_FS[] = {/* 36 *//* LUN 0 */0x00,0x80,0x02,0x02,(STANDARD_INQUIRY_DATA_LEN - 5),0x00,0x00,0x00,'S', 'T', 'M', ' ', ' ', ' ', ' ', ' ', /* Manufacturer : 8 bytes */'P', 'r', 'o', 'd', 'u', 'c', 't', ' ', /* Product      : 16 Bytes */' ', ' ', ' ', ' ', ' ', ' ', ' ', ' ','0', '.', '0' ,'1'                      /* Version      : 4 Bytes */
};
/* USER CODE END INQUIRY_DATA_FS *//* USER CODE BEGIN PRIVATE_VARIABLES *//* USER CODE END PRIVATE_VARIABLES *//*** @}*//** @defgroup USBD_STORAGE_Exported_Variables* @brief Public variables.* @{*/extern USBD_HandleTypeDef hUsbDeviceFS;/* USER CODE BEGIN EXPORTED_VARIABLES *//* USER CODE END EXPORTED_VARIABLES *//*** @}*//** @defgroup USBD_STORAGE_Private_FunctionPrototypes* @brief Private functions declaration.* @{*/static int8_t STORAGE_Init_FS(uint8_t lun);
static int8_t STORAGE_GetCapacity_FS(uint8_t lun, uint32_t *block_num, uint16_t *block_size);
static int8_t STORAGE_IsReady_FS(uint8_t lun);
static int8_t STORAGE_IsWriteProtected_FS(uint8_t lun);
static int8_t STORAGE_Read_FS(uint8_t lun, uint8_t *buf, uint32_t blk_addr, uint16_t blk_len);
static int8_t STORAGE_Write_FS(uint8_t lun, uint8_t *buf, uint32_t blk_addr, uint16_t blk_len);
static int8_t STORAGE_GetMaxLun_FS(void);/* USER CODE BEGIN PRIVATE_FUNCTIONS_DECLARATION *//* USER CODE END PRIVATE_FUNCTIONS_DECLARATION *//*** @}*/USBD_StorageTypeDef USBD_Storage_Interface_fops_FS =
{STORAGE_Init_FS,STORAGE_GetCapacity_FS,STORAGE_IsReady_FS,STORAGE_IsWriteProtected_FS,STORAGE_Read_FS,STORAGE_Write_FS,STORAGE_GetMaxLun_FS,(int8_t *)STORAGE_Inquirydata_FS
};/* Private functions ---------------------------------------------------------*/
/*** @brief  Initializes the storage unit (medium) over USB FS IP* @param  lun: Logical unit number.* @retval USBD_OK if all operations are OK else USBD_FAIL*/
int8_t STORAGE_Init_FS(uint8_t lun)
{/* USER CODE BEGIN 2 *///UNUSED(lun);W25QXX_Init();return (USBD_OK);/* USER CODE END 2 */
}/*** @brief  Returns the medium capacity.* @param  lun: Logical unit number.* @param  block_num: Number of total block number.* @param  block_size: Block size.* @retval USBD_OK if all operations are OK else USBD_FAIL*/
int8_t STORAGE_GetCapacity_FS(uint8_t lun, uint32_t *block_num, uint16_t *block_size)
{/* USER CODE BEGIN 3 *///UNUSED(lun);*block_num  = STORAGE_BLK_NBR;*block_size = STORAGE_BLK_SIZ;return (USBD_OK);/* USER CODE END 3 */
}/*** @brief   Checks whether the medium is ready.* @param  lun:  Logical unit number.* @retval USBD_OK if all operations are OK else USBD_FAIL*/
int8_t STORAGE_IsReady_FS(uint8_t lun)
{/* USER CODE BEGIN 4 *///UNUSED(lun);return (USBD_OK);/* USER CODE END 4 */
}/*** @brief  Checks whether the medium is write protected.* @param  lun: Logical unit number.* @retval USBD_OK if all operations are OK else USBD_FAIL*/
int8_t STORAGE_IsWriteProtected_FS(uint8_t lun)
{/* USER CODE BEGIN 5 *///UNUSED(lun);return (USBD_OK);/* USER CODE END 5 */
}/*** @brief  Reads data from the medium.* @param  lun: Logical unit number.* @param  buf: data buffer.* @param  blk_addr: Logical block address.* @param  blk_len: Blocks number.* @retval USBD_OK if all operations are OK else USBD_FAIL*/
int8_t STORAGE_Read_FS(uint8_t lun, uint8_t *buf, uint32_t blk_addr, uint16_t blk_len)
{/* USER CODE BEGIN 6 *///UNUSED(lun);//UNUSED(buf);//UNUSED(blk_addr);//UNUSED(blk_len);W25QXX_Read(buf, blk_addr*STORAGE_BLK_SIZ, blk_len*STORAGE_BLK_SIZ);return (USBD_OK);/* USER CODE END 6 */
}/*** @brief  Writes data into the medium.* @param  lun: Logical unit number.* @param  buf: data buffer.* @param  blk_addr: Logical block address.* @param  blk_len: Blocks number.* @retval USBD_OK if all operations are OK else USBD_FAIL*/
int8_t STORAGE_Write_FS(uint8_t lun, uint8_t *buf, uint32_t blk_addr, uint16_t blk_len)
{/* USER CODE BEGIN 7 *///UNUSED(lun);//UNUSED(buf);//UNUSED(blk_addr);//UNUSED(blk_len);W25QXX_Write(buf, blk_addr*STORAGE_BLK_SIZ, blk_len*STORAGE_BLK_SIZ);return (USBD_OK);/* USER CODE END 7 */
}/*** @brief  Returns the Max Supported LUNs.* @param  None* @retval Lun(s) number.*/
int8_t STORAGE_GetMaxLun_FS(void)
{/* USER CODE BEGIN 8 */return (STORAGE_LUN_NBR - 1);/* USER CODE END 8 */
}/* USER CODE BEGIN PRIVATE_FUNCTIONS_IMPLEMENTATION *//* USER CODE END PRIVATE_FUNCTIONS_IMPLEMENTATION *//*** @}*//*** @}*/

(番外)由上面的设置可以看出设计扩容盘的方式,如把8M的盘扩容成64M,则进行两步操作即可:

  1. 将STORAGE_BLK_NBR放大8倍从而盘容量识别扩大为64M
  2. 在读写函数里,对操作地址进行处理,即把操作地址对8M空间取余,这样刚过8M尾部空间的操作就会跳到头部空间进行,当然如果是写操作就会产生覆盖
    扩容盘是一种循环访问非常规方式,一般在行车记录仪等监控领域出现较多,用户想存储更长时间的数据,但实际上要查数据时都是近期数据,扩容盘能够保持对近期数据的记录,因此不良商家卖出扩容盘非法牟利。扩容盘的缺点是实际容量小于标称容量,要查远期数据是被覆盖丢失的,另一个缺点是如果一个文件正好存储时跨过了实际容量尾部,那么这个文件对PC端时损坏文件不能读取,如果正好这个近期文件是重要取证文件,则是不良事件。

然后在main.c里根据串口输入命令(16进制单字节)实现如下功能:
0x01. 读取FLASH ID
0x02. 装载FATS文件系统
0x03: 创建/打开文件并从头位置写入数据
0x04: 打开文件并从头位置读入数据
0x05: 创建/打开文件并从特定位置写入数据
0x06: 打开文件并从特定位置读入数据
完整的代码实现如下:

/* USER CODE BEGIN Header */
/********************************************************************************* @file           : main.c* @brief          : Main program body******************************************************************************* @attention** Copyright (c) 2023 STMicroelectronics.* All rights reserved.** This software is licensed under terms that can be found in the LICENSE file* in the root directory of this software component.* If no LICENSE file comes with this software, it is provided AS-IS.********************************************************************************/
//Written by Pegasus Yu in 2023
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "fatfs.h"
#include "usb_device.h"/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
#include "usart.h"
#include "W25QXX.h"
#include <string.h>
/* USER CODE END Includes *//* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */
__IO float usDelayBase;
void PY_usDelayTest(void)
{__IO uint32_t firstms, secondms;__IO uint32_t counter = 0;firstms = HAL_GetTick()+1;secondms = firstms+1;while(uwTick!=firstms) ;while(uwTick!=secondms) counter++;usDelayBase = ((float)counter)/1000;
}void PY_Delay_us_t(uint32_t Delay)
{__IO uint32_t delayReg;__IO uint32_t usNum = (uint32_t)(Delay*usDelayBase);delayReg = 0;while(delayReg!=usNum) delayReg++;
}void PY_usDelayOptimize(void)
{__IO uint32_t firstms, secondms;__IO float coe = 1.0;firstms = HAL_GetTick();PY_Delay_us_t(1000000) ;secondms = HAL_GetTick();coe = ((float)1000)/(secondms-firstms);usDelayBase = coe*usDelayBase;
}void PY_Delay_us(uint32_t Delay)
{__IO uint32_t delayReg;__IO uint32_t msNum = Delay/1000;__IO uint32_t usNum = (uint32_t)((Delay%1000)*usDelayBase);if(msNum>0) HAL_Delay(msNum);delayReg = 0;while(delayReg!=usNum) delayReg++;
}
/* USER CODE END PTD *//* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD *//* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM *//* USER CODE END PM *//* Private variables ---------------------------------------------------------*/SPI_HandleTypeDef hspi2;UART_HandleTypeDef huart1;/* USER CODE BEGIN PV */
uint8_t uart1_rx[16];
uint8_t cmd;uint8_t Flash_mount_status = 0; //FLASH fats mount status indication (0: unmount; 1: mount)
uint8_t FATS_Buff[_MAX_SS]; //Buffer for f_mkfs() operationFRESULT retFLASH;
FIL file;
FATFS *fs;UINT bytesread;
UINT byteswritten;
uint8_t rBuffer[20];      //Buffer for read
uint8_t WBuffer[20] ={1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20}; //Buffer for write#define user_sector_byte_size 512
uint8_t flashbuffer[user_sector_byte_size];extern char USERPath[4];
/* USER CODE END PV *//* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
void PeriphCommonClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_USART1_UART_Init(void);
static void MX_SPI2_Init(void);
/* USER CODE BEGIN PFP *//* USER CODE END PFP *//* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 *//* USER CODE END 0 *//*** @brief  The application entry point.* @retval int*/
int main(void)
{/* USER CODE BEGIN 1 */Flash_mount_status = 0;uint32_t FLASH_Read_Size;char * dpath = "0:"; //Disk Pathfor(uint8_t i=0; i<4; i++){USERPath[i] = *(dpath+i);}const TCHAR* filepath = "0:test.txt";/* USER CODE END 1 *//* MCU Configuration--------------------------------------------------------*//* Reset of all peripherals, Initializes the Flash interface and the Systick. */HAL_Init();/* USER CODE BEGIN Init *//* USER CODE END Init *//* Configure the system clock */SystemClock_Config();/* Configure the peripherals common clocks */PeriphCommonClock_Config();/* USER CODE BEGIN SysInit *//* USER CODE END SysInit *//* Initialize all configured peripherals */MX_GPIO_Init();MX_USART1_UART_Init();MX_SPI2_Init();MX_FATFS_Init();MX_USB_DEVICE_Init();/* USER CODE BEGIN 2 */PY_usDelayTest();PY_usDelayOptimize();HAL_UART_Receive_IT(&huart1, uart1_rx, 1);W25QXX_Init();/* USER CODE END 2 *//* Infinite loop *//* USER CODE BEGIN WHILE */while (1){if(cmd==1) //Read ID{cmd = 0;printf("FLASH ID=0x%x\r\n\r\n", W25QXX_ReadID());printf("W25Q80_ID: 0XEF13\r\n");printf("W25Q16_ID: 0XEF14\r\n");printf("W25Q32_ID: 0XEF15\r\n");printf("W25Q64_ID: 0XEF16\r\n");printf("W25Q128_ID: 0XEF17\r\n");printf("W25Q256_ID: 0XEF18\r\n");printf("W25Q512_ID: 0XEF18\r\n");printf("W25Q1024_ID: 0XEF20\r\n");}else if(cmd==2) //Flash File System Mount{cmd = 0;retFLASH=f_mount(&USERFatFS, (TCHAR const*)USERPath, 1);if (retFLASH != FR_OK){printf("File system mount failure: %d\r\n", retFLASH);if(retFLASH==FR_NO_FILESYSTEM){printf("No file system. Now to format......\r\n");retFLASH = f_mkfs((TCHAR const*)USERPath, FM_FAT, 1024, FATS_Buff, sizeof(FATS_Buff)); //FLASH formattingif(retFLASH == FR_OK){printf("FLASH formatting success!\r\n");}else{printf("FLASH formatting failure!\r\n");}}}else{Flash_mount_status = 1;printf("File system mount success\r\n");}}else if(cmd==3) //File creation and write{cmd = 0;if(Flash_mount_status==0) printf("\r\nFLASH File system not mounted: %d\r\n",retFLASH);else{retFLASH = f_open( &file, filepath, FA_CREATE_ALWAYS | FA_WRITE );  //Open or create fileif(retFLASH == FR_OK){printf("\r\nFile open or creation successful\r\n");retFLASH = f_write( &file, (const void *)WBuffer, sizeof(WBuffer), &byteswritten); //Write dataif(retFLASH == FR_OK){printf("\r\nFile write successful\r\n");}else{printf("\r\nFile write error: %d\r\n",retFLASH);}f_close(&file);   //Close file}else{printf("\r\nFile open or creation error %d\r\n",retFLASH);}}}else if(cmd==4) //File read{cmd = 0;if(Flash_mount_status==0) printf("\r\nFLASH File system not mounted: %d\r\n",retFLASH);else{retFLASH = f_open( &file, filepath, FA_OPEN_EXISTING | FA_READ); //Open fileif(retFLASH == FR_OK){printf("\r\nFile open successful\r\n");retFLASH = f_read( &file, (void *)rBuffer, sizeof(rBuffer), &bytesread); //Read dataif(retFLASH == FR_OK){printf("\r\nFile read successful\r\n");PY_Delay_us_t(200000);FLASH_Read_Size = sizeof(rBuffer);for(uint16_t i = 0;i < FLASH_Read_Size;i++){printf("%d ", rBuffer[i]);}printf("\r\n");}else{printf("\r\nFile read error: %d\r\n", retFLASH);}f_close(&file); //Close file}else{printf("\r\nFile open error: %d\r\n", retFLASH);}}}else if(cmd==5) //File locating write{cmd = 0;if(Flash_mount_status==0) printf("\r\nFLASH File system not mounted: %d\r\n",retFLASH);else{retFLASH = f_open( &file, filepath, FA_CREATE_ALWAYS | FA_WRITE);  //Open or create fileif(retFLASH == FR_OK){printf("\r\nFile open or creation successful\r\n");retFLASH=f_lseek( &file, f_tell(&file) + sizeof(WBuffer) ); //move file operation pointer, f_tell(&file) gets file head locatingif(retFLASH == FR_OK){retFLASH = f_write( &file, (const void *)WBuffer, sizeof(WBuffer), &byteswritten);if(retFLASH == FR_OK){printf("\r\nFile locating write successful\r\n");}else{printf("\r\nFile locating write error: %d\r\n", retFLASH);}}else{printf("\r\nFile pointer error: %d\r\n",retFLASH);}f_close(&file);   //Close file}else{printf("\r\nFile open or creation error %d\r\n",retFLASH);}}}else if(cmd==6) //File locating read{cmd = 0;if(Flash_mount_status==0) printf("\r\nFLASH File system not mounted: %d\r\n",retFLASH);else{retFLASH = f_open(&file, filepath, FA_OPEN_EXISTING | FA_READ); //Open fileif(retFLASH == FR_OK){printf("\r\nFile open successful\r\n");retFLASH =  f_lseek(&file,f_tell(&file)+ sizeof(WBuffer)/2); //move file operation pointer, f_tell(&file) gets file head locatingif(retFLASH == FR_OK){retFLASH = f_read( &file, (void *)rBuffer, sizeof(rBuffer), &bytesread);if(retFLASH == FR_OK){printf("\r\nFile locating read successful\r\n");PY_Delay_us_t(200000);FLASH_Read_Size = sizeof(rBuffer);for(uint16_t i = 0;i < FLASH_Read_Size;i++){printf("%d ",rBuffer[i]);}printf("\r\n");}else{printf("\r\nFile locating read error: %d\r\n",retFLASH);}}else{printf("\r\nFile pointer error: %d\r\n",retFLASH);}f_close(&file);}else{printf("\r\nFile open error: %d\r\n",retFLASH);}}}/* USER CODE END WHILE *//* USER CODE BEGIN 3 */}/* USER CODE END 3 */
}/*** @brief System Clock Configuration* @retval None*/
void SystemClock_Config(void)
{RCC_OscInitTypeDef RCC_OscInitStruct = {0};RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};/** Supply configuration update enable*/HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY);/** Configure the main internal regulator output voltage*/__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);while(!__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY)) {}__HAL_RCC_SYSCFG_CLK_ENABLE();__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE0);while(!__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY)) {}/** Initializes the RCC Oscillators according to the specified parameters* in the RCC_OscInitTypeDef structure.*/RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48|RCC_OSCILLATORTYPE_HSI;RCC_OscInitStruct.HSIState = RCC_HSI_DIV1;RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;RCC_OscInitStruct.PLL.PLLM = 4;RCC_OscInitStruct.PLL.PLLN = 60;RCC_OscInitStruct.PLL.PLLP = 2;RCC_OscInitStruct.PLL.PLLQ = 2;RCC_OscInitStruct.PLL.PLLR = 2;RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_3;RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOWIDE;RCC_OscInitStruct.PLL.PLLFRACN = 0;if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK){Error_Handler();}/** Initializes the CPU, AHB and APB buses clocks*/RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2|RCC_CLOCKTYPE_D3PCLK1|RCC_CLOCKTYPE_D1PCLK1;RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV2;RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV2;RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2;RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2;RCC_ClkInitStruct.APB4CLKDivider = RCC_APB4_DIV2;if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4) != HAL_OK){Error_Handler();}
}/*** @brief Peripherals Common Clock Configuration* @retval None*/
void PeriphCommonClock_Config(void)
{RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0};/** Initializes the peripherals clock*/PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CKPER;PeriphClkInitStruct.CkperClockSelection = RCC_CLKPSOURCE_HSI;if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct) != HAL_OK){Error_Handler();}
}/*** @brief SPI2 Initialization Function* @param None* @retval None*/
static void MX_SPI2_Init(void)
{/* USER CODE BEGIN SPI2_Init 0 *//* USER CODE END SPI2_Init 0 *//* USER CODE BEGIN SPI2_Init 1 *//* USER CODE END SPI2_Init 1 *//* SPI2 parameter configuration*/hspi2.Instance = SPI2;hspi2.Init.Mode = SPI_MODE_MASTER;hspi2.Init.Direction = SPI_DIRECTION_2LINES;hspi2.Init.DataSize = SPI_DATASIZE_8BIT;hspi2.Init.CLKPolarity = SPI_POLARITY_LOW;hspi2.Init.CLKPhase = SPI_PHASE_1EDGE;hspi2.Init.NSS = SPI_NSS_SOFT;hspi2.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2;hspi2.Init.FirstBit = SPI_FIRSTBIT_MSB;hspi2.Init.TIMode = SPI_TIMODE_DISABLE;hspi2.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;hspi2.Init.CRCPolynomial = 0x0;hspi2.Init.NSSPMode = SPI_NSS_PULSE_ENABLE;hspi2.Init.NSSPolarity = SPI_NSS_POLARITY_LOW;hspi2.Init.FifoThreshold = SPI_FIFO_THRESHOLD_01DATA;hspi2.Init.TxCRCInitializationPattern = SPI_CRC_INITIALIZATION_ALL_ZERO_PATTERN;hspi2.Init.RxCRCInitializationPattern = SPI_CRC_INITIALIZATION_ALL_ZERO_PATTERN;hspi2.Init.MasterSSIdleness = SPI_MASTER_SS_IDLENESS_00CYCLE;hspi2.Init.MasterInterDataIdleness = SPI_MASTER_INTERDATA_IDLENESS_00CYCLE;hspi2.Init.MasterReceiverAutoSusp = SPI_MASTER_RX_AUTOSUSP_DISABLE;hspi2.Init.MasterKeepIOState = SPI_MASTER_KEEP_IO_STATE_DISABLE;hspi2.Init.IOSwap = SPI_IO_SWAP_DISABLE;if (HAL_SPI_Init(&hspi2) != HAL_OK){Error_Handler();}/* USER CODE BEGIN SPI2_Init 2 *//* USER CODE END SPI2_Init 2 */}/*** @brief USART1 Initialization Function* @param None* @retval None*/
static void MX_USART1_UART_Init(void)
{/* USER CODE BEGIN USART1_Init 0 *//* USER CODE END USART1_Init 0 *//* USER CODE BEGIN USART1_Init 1 *//* USER CODE END USART1_Init 1 */huart1.Instance = USART1;huart1.Init.BaudRate = 115200;huart1.Init.WordLength = UART_WORDLENGTH_8B;huart1.Init.StopBits = UART_STOPBITS_1;huart1.Init.Parity = UART_PARITY_NONE;huart1.Init.Mode = UART_MODE_TX_RX;huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;huart1.Init.OverSampling = UART_OVERSAMPLING_16;huart1.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;huart1.Init.ClockPrescaler = UART_PRESCALER_DIV1;huart1.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;if (HAL_UART_Init(&huart1) != HAL_OK){Error_Handler();}if (HAL_UARTEx_SetTxFifoThreshold(&huart1, UART_TXFIFO_THRESHOLD_1_8) != HAL_OK){Error_Handler();}if (HAL_UARTEx_SetRxFifoThreshold(&huart1, UART_RXFIFO_THRESHOLD_1_8) != HAL_OK){Error_Handler();}if (HAL_UARTEx_DisableFifoMode(&huart1) != HAL_OK){Error_Handler();}/* USER CODE BEGIN USART1_Init 2 *//* USER CODE END USART1_Init 2 */}/*** @brief GPIO Initialization Function* @param None* @retval None*/
static void MX_GPIO_Init(void)
{GPIO_InitTypeDef GPIO_InitStruct = {0};/* GPIO Ports Clock Enable */__HAL_RCC_GPIOB_CLK_ENABLE();__HAL_RCC_GPIOA_CLK_ENABLE();/*Configure GPIO pin Output Level */HAL_GPIO_WritePin(GPIOB, GPIO_PIN_12, GPIO_PIN_SET);/*Configure GPIO pin : PB12 */GPIO_InitStruct.Pin = GPIO_PIN_12;GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;GPIO_InitStruct.Pull = GPIO_NOPULL;GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);}/* USER CODE BEGIN 4 */
void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart)
{if(huart==&huart1){cmd = uart1_rx[0];HAL_UART_Receive_IT(&huart1, uart1_rx, 1);}}
/* USER CODE END 4 *//*** @brief  This function is executed in case of error occurrence.* @retval None*/
void Error_Handler(void)
{/* USER CODE BEGIN Error_Handler_Debug *//* User can add his own implementation to report the HAL error return state */__disable_irq();while (1){}/* USER CODE END Error_Handler_Debug */
}#ifdef  USE_FULL_ASSERT
/*** @brief  Reports the name of the source file and the source line number*         where the assert_param error has occurred.* @param  file: pointer to the source file name* @param  line: assert_param error line source number* @retval None*/
void assert_failed(uint8_t *file, uint32_t line)
{/* USER CODE BEGIN 6 *//* User can add his own implementation to report the file name and line number,ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) *//* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

STM32例程测试

串口指令0x01测试效果如下:
在这里插入图片描述

串口指令0x02测试效果如下:
在这里插入图片描述

串口指令0x03测试效果如下:
在这里插入图片描述

串口指令0x04测试效果如下:
在这里插入图片描述

串口指令0x05测试效果如下:
在这里插入图片描述

串口指令0x06测试效果如下:
在这里插入图片描述
通过串口对FLASH对操作后,可以将STM32 USB接口连接到PC, 从PC端可以看到U盘接入,打开后可以看到通过串口建立和操作的文件:
在这里插入图片描述
在这里插入图片描述
串口写入文件里的是1~20范围的16进制数据,这里显示为非常规字符,如果串口写入文件里的是英文字母对应的ASCII码16进制数据,文件里也就会显示为英文字母。
当通过U盘形式对文件进行操作后,同样也可以再通过串口对U盘形式操作过的文件访问操作。

STM32例程下载

STM32H750VBT6 模拟U盘桥接SPI总线FATS读写FLASH W25QXX例程下载

U盘模式升级方式

一种STM32升级方式为通过模拟U盘,从PC端将升级文件(.bin文件)存储进到外部FLASH里,STM32重新上电时识别标识从外部FLASH里将版本拷贝进到内部FLASH跳转空间,然后跳转执行。这是IAP升级的U盘接口常见方式,可以参考串口IAP升级过程,主要区别是版本数据获得方式不同。
一个不复杂的问题是为什么不从PC端直接写入.bin文件进到内部FLASH里,因为文件管理系统会占用额外的空间,也会导致文件放置首地址(跳转地址)易变,因此对MCU有限的内部FLASH空间而言不利资源使用。

–End–

本文来自互联网用户投稿,该文观点仅代表作者本人,不代表本站立场。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如若转载,请注明出处:http://www.rhkb.cn/news/349020.html

如若内容造成侵权/违法违规/事实不符,请联系长河编程网进行投诉反馈email:809451989@qq.com,一经查实,立即删除!

相关文章

vs2019 c++20规范 STL 库中头文件 <atomic> 源码注释及探讨几个知识点

&#xff08;1 探讨一&#xff09; 模板类 atomic 的继承关系与数据结构如下&#xff1a; (2 探讨二 ) 可见 atomic 的 fetch_xx 函数&#xff0c;返回的都是 atomic 中存储的旧值。测试如下&#xff1a; 谢谢

无公网IP与服务器完成企业微信网页应用开发远程调试详细流程

文章目录 前言1. Windows安装Cpolar2. 创建Cpolar域名3. 创建企业微信应用4. 定义回调本地接口5. 回调和可信域名接口校验6. 设置固定Cpolar域名7. 使用固定域名校验 前言 本文主要介绍如何在企业微信开发者中心通过使用内网穿透工具提供的公网域名成功验证回调本地接口服务! …

互联网应用主流框架整合之SpringMVC初始化及各组件工作原理

Spring MVC的初始化和流程 MVC理念的发展 SpringMVC是Spring提供给Web应用领域的框架设计&#xff0c;MVC分别是Model-View-Controller的缩写&#xff0c;它是一个设计理念&#xff0c;不仅仅存在于Java中&#xff0c;各类语言及开发均可用&#xff0c;其运转流程和各组件的应…

PFC旁路二极管、继电器驱动电路以及PFC主功率

R001和R002以及R003三个电阻作用是限放X电容上的电 整流桥串联两个BJ1和BJ2 电容C3:给整流桥储能&#xff0c;给后续llc供电 PFC工作是正弦波上叠加高频电流 PFC功率部分 2个PFC电感&#xff08;选择两个磁芯骨架小&#xff0c;有利于散热&#xff09;、2个续流二极管&…

【Hudi】核心概念-基本概念

目录 基本概念时间轴(TimeLine)Instant action:在表上执行的操作类型Instant timeState两个时间概念 文件布局(File Layout)索引(Index)原理索引选项全局索引与非全局索引索引的选择策略 表类型(Table Types)查询类型Snapshot QueriesIncremental QueriesRead Optimized Querie…

出现“由于找不到msvcr120.dll,无法继继续执行代码”提示的问题处理方法

本文章针对出现“由于找不到msvcr120.dll,无法继续执行代码”的问题进行深入剖析&#xff0c;并提供了两种有效的解决方案&#xff0c;方便大家能快速恢复正常工作状态。 一.关于msvcr120.dll文件部分介绍 “由于找不到msvcr120.dll,无法继续执行代码”常发生在我们打开一个软…

web端使用高德地图

web端使用高德地图 一、申请高德key和秘钥二、在项目中引入所需功能js、css文件三、实现地图选点、回显选点四、自定义地图 一、申请高德key和秘钥 申请高德key 申请成功后可以得到key 二、在项目中引入所需功能js、css文件 <script src"https://webapi.amap.com/m…

流程设计的基本步骤

背景 公司为什么要流程&#xff0c;已经有专门章节进行阐述&#xff1b; 什么是流程&#xff0c;已经有专门章节进行专门阐述&#xff1b; 那么接下来这个章节讨论&#xff0c;流程设计的基本步骤&#xff0c;那么谁来设计流程呢&#xff0c;让一个部门的员工来设计一份流程…

【RabbitMQ】RabbitMQ配置与交换机学习

文章目录 简介安装和部署1. 安装RabbitMQ2.创建virtual-host3. 添加依赖4.修改配置文件 WorkQueues模型1.编写消息发送测试类2.编写消息接收&#xff08;监听&#xff09;类3. 实现能者多劳 交换机Fanout交换机1.消息发送2.消息监听 Direct交换机1.消息发送2.消息接收 Topic交换…

vue3 vant4 仿京东分类功能实现

Ⅰ- 壹 - 功能展示和使用需求 需求描述 基于vant 实现,仿京东分类功能实现样式交互等基本实现,细节可能需要优化 地址 https://gitee.com/wswhq/vue3-vant-temp/tree/master/src/view/ClassIfication 功能展示 Ⅱ - 贰 - 封装思路 不表述了自己看代码吧 Ⅲ - 叁 - 使用 …

梯度下降法、牛顿法、条件熵

梯度下降法、牛顿法&#xff08;可见南瓜书&#xff09; 梯度下降法 深度学习&#xff1a;梯度下降法数学表示式的详细推导 牛顿法 条件熵 在李航老师的书中&#xff0c;第六章最大熵模型这里有个条件熵的定义&#xff1a; 推导如下&#xff1a; 其他一些事实&#xff1a;…

Vue22-v-model收集表单数据

一、效果图 二、代码 2-1、HTML代码 2-2、vue代码 1、v-model单选框的收集信息 v-model&#xff1a;默认收集的就是元素中的value值。 单选框添加默认值&#xff1a; 2、v-model多选框的收集信息 ①、多个选择的多选 注意&#xff1a; 此处的hobby要是数组&#xff01;&…

springboot 整合redis问题,缓存击穿,穿透,雪崩,分布式锁

boot整合redis 压力测试出现失败 解决方案 排除lettuce 使用jedis <!-- 引入redis --><dependency><groupId>org.springframework.boot</groupId><artifactId>spring-boot-starter-data-redis</artifactId><exclusions><exclus…

【电子信息工程专业课】学习记录

数字信号处理 离散时间信号与系统 周期延拓 一个连续时间信号经过理想采样后&#xff0c;其频谱将沿着频率轴以采样频率Ωs 2π / T 为间隔而重复。 混频 各周期的延拓分量产生频谱交替的现象 奈奎斯特采样定理 fs > 2fh Z变换 收敛域&#xff1a;使任意给定序列x(n)的Z变…

Sqoop学习详细介绍!!

一、Sqoop介绍 Sqoop是一款开源的工具&#xff0c;主要用于在Hadoop(HDFS/Hive/HBase)与传统的数据库(mysql、postgresql...)间进行数据的传递&#xff0c;可以将一个关系型数据库&#xff08;例如 &#xff1a; MySQL ,Oracle ,Postgres等&#xff09;中的数据导进到Hadoop的H…

2024年金融、贸易与创意产业国际会议(ICFTCI 2024)

2024 International Conference on Financial Trade and Creative Industries 【1】大会信息 会议简称&#xff1a;ICFTCI 2024 大会地点&#xff1a;中国西安 投稿邮箱&#xff1a;icftcisub-paper.com 【2】会议简介 2024年金融贸易与创意产业国际会议即将召开&#xff…

【Python】已完美解决:executemany() takes exactly 2 positional arguments (3 given)

文章目录 一、问题背景二、可能出错的原因三、错误代码示例四、正确代码示例&#xff08;结合实战场景&#xff09;五、注意事项 已解决&#xff1a;Python中executemany()方法参数数量错误的问题 一、问题背景 在Python的数据库编程中&#xff0c;executemany()方法是一个常…

loading组件封装原理

以vue3为例&#xff0c;采用ts 的语言 首先可对所需数据定义在接口中 interface Prop{ //核心所需的就是 lading:boolean ,type: lading | skeleton} 进行调用 封装的话采用的是插槽 <div v-if"loading" ><slot name"template"><…

随手记:uniapp图片展示,剩余的堆叠

UI效果图&#xff1a; 实现思路&#xff1a; 循环图片数组&#xff0c;只展示几张宽度就为几张图片边距的宽度&#xff0c;剩下的图片直接堆叠展示 点击预览的时候传入当前的下标&#xff0c;如果是点击堆叠的话&#xff0c;下标从堆叠数量开始计算 <template><…

私有云和多云管理平台 | Cloudpods v3.11.4 正式发布

本次 3.11.4 更新亮点为&#xff1a;系统镜像引入社区镜像&#xff0c;用户可以一键导入各主流开源操作系统镜像&#xff0c;方便用户上手使用。持续迭代共享 LVM&#xff0c;支持快照&#xff0c;主备机等特性&#xff0c;修复迁移删除镜像缓存等 BUG。 功能优化 【费用】费…